You took off a bunch of stuff but didn’t show the cross/over
@su-mu4 ай бұрын
4:13
@christopherwright32495 ай бұрын
The last few seconds of this video.. was that the camshaft sensor? 1:01 3:40
@markusstorm24207 ай бұрын
dumb question but if the covers are cracked or missing bolts will that cause a significant oil leak? Sister has this car and some shade tree mechanic changed her timing belts and now there is a slight leak by the AC compressor. I can't tell if it's coming from around the timing belt covers or maybe it's time for the oil pan gasket to be changed
@ziggiesaquaticexotics82708 ай бұрын
My slider pin bolts were so shot and wore out the bottom was totally gone from the truck n the top one was fully out un screwed 😂 shit was flopping all over it ate my rotor up it was basically gone 😂 and ate up the inside of my fuckin nice rim 🤦♂️
@shlomoameleh786210 ай бұрын
Thenk you
@veroniquebuiting768510 ай бұрын
Hi, sorry but I need to know what is that round white thing under the filter?
@PimpDaddyDisco Жыл бұрын
T-45 or 7mm allen?
@billwesley2213 Жыл бұрын
Thank you for this!! Very helpful
@3000XJz2 жыл бұрын
Heads up to anyone that sees this needing to find timing, left cam has 2 dimples in the cam about 80-90⁰ to the right of the yellow mark, line them up to the 2 notches above the cam.
@3000XJz2 жыл бұрын
Not entirely sure how long this post will be available but here is a link that'll show it facebook.com/groups/234197520082381/permalink/2143959369106177/
@marcelkielliger63882 жыл бұрын
How the hell do you remove the left timingbelt cover without braking it.. and the idler pulley and bracket withou swearing.! Puting it back was even worse. Had to remove the alternator and AC compressor to get any access.
@asifahsan51042 жыл бұрын
To open the caliper bracket which way the bolts turns (21mm bolts)? Clockwise or counterclockwise?
@ansonandson3 жыл бұрын
Aww the infamous 2000 camry the car that can make a mechanic out of any man
@tomservo53473 жыл бұрын
Can you carefully screw the caliper piston back in with channel locks? I wouldn't think there would be much resistance screwing them back in if everything is in working order.
@gabrieledwards14773 жыл бұрын
Does anyone know where to check power steering fluid on a 2007 aura XR
@stopthephilosophicalzombie90173 жыл бұрын
Great video. Btw, what's the direction of rotation of the engine? I've got a rattle/rumble that happens at low rpms and goes away above 1000. I'm pretty sure it's the timing belt tensioner so I figured I'd do the timing belt, water pump and tensioner all in one go.
@boatdude128 ай бұрын
What did it end up being? I have the same from 800-1800RPM.
@stopthephilosophicalzombie90178 ай бұрын
@@boatdude12 It was a bad tensioner and idler pully bearing. Also the bracket that holds the idler bearing is warped on a lot of these 626 cars, so even if you replace the bearing it will fail again the same way. My harmonic balancer failed also in the same period.
@prettybubbles89543 жыл бұрын
How many quartz of oil
@jasonl31854 жыл бұрын
Do you have to put it in service mode I know on new ones you do but I have a 07
@kwilli954 жыл бұрын
Jason L you do not need to put this model in service mode
@jasonl31854 жыл бұрын
@@kwilli95 thanks I started yesterday and found out it has a Manuel e-brake that helps to know no need to put in mode unless you have a electric e-brake
@zaow824 жыл бұрын
More "how to" videos should be like this. Quick and straight to the point.
@herman4524 жыл бұрын
Thanks. Had a piece of paper in my fan making noise. What an easy fix (once I knew only three screws held it in).
@mrslcom5 жыл бұрын
Is there an updated fix to this defect? Having to replace this gasket repeatedly every 2-3 years.
@gantmj4 жыл бұрын
Go here and read Rich's comments: www.autoserviceprofessional.com/5350/coolant-crossover-leak
@andys72525 жыл бұрын
Make sure #1 piston is at top.NOT at BDC. remove plug and check with a hose.if wrong turn crank bolt one more revolution \look at 2:48 o0n video you will see two marks in housing and gear 1 tooth apart.they knew you would not see same mark as right gear
@ericjohnston71895 жыл бұрын
Such a big help ! Better than most other I have seen thank you
@jeffkeryk35505 жыл бұрын
No lube on the pad ears? No anti-squeal goop on the pad backs? You did check the sliders; I always pull 'em, clean 'em and regrease 'em. All good...
@isomjenkins17585 жыл бұрын
What's the firing order
@awoljones49085 жыл бұрын
Thank you I could not get that caliper piston back in lol
@dq71434 жыл бұрын
Notice the caliper piston is twisted back in - not pushed back in.
@golemcoreable5 жыл бұрын
What is that component call before the belt tensioner
@Mar5_215 жыл бұрын
Dude, best “how to” video ever
@themoneyboys7025 жыл бұрын
what's firing order
@clintschadek94015 жыл бұрын
TIP- Spray the piston boot with WD-40 or a spray lubricant before you twist your piston in, or it may start to twist and possibly rip. aswell as your twisting the piston in your boot may have an air bubble you can burp it by carfully sticking a small screw driver against the piston and the boot and the pressure will release
@Alex-uj6sq5 жыл бұрын
Bad idea as WD-40 eats rubber.(Unless buying specialized WD-40 specifically safe for rubber) Best to use fluid film or something akin to that.
@clintschadek94015 жыл бұрын
@@Alex-uj6sq Certain types of rubber will swell upon prolonged immersion. There are applications involving rubber and some plastics, which should be approached with caution or avoided when using WD-40®. Always test surface first. Right off there website, worked fine for me. had no problems with swelling rubber or anything. I've used wd 40 on many different types of rubbers without any issues.
@dq71434 жыл бұрын
The ideal product to use on rubber boots is silicone grease. It is non petroleum based and prolongs the life of rubber parts greatly.
@tomservo53473 жыл бұрын
@@dq7143 I spray all of my rubber components with silicone spray.
@christopherg77335 жыл бұрын
What kind of oil?
@prettybubbles89543 жыл бұрын
Synthetic 5w30
@NHSSHINOBI5 жыл бұрын
Thanks, this helped
@silverfalconhopkins5 жыл бұрын
What are the coolant crossover pipe bolt torque specs
@anthonyp45305 жыл бұрын
I lost the 17 mm bolt what are the specs on that one?
@ansonandson3 жыл бұрын
Sounds like me
@timdawg7475 жыл бұрын
I just changed my 2008 Saturn 3.5L Spark Plugs, Spark Plug Wires and Ignition Coil.. The info online makes this repair seem very difficult.. Some instructing you to take off the Intake Manifold.. FALSE. I didn't to do any of that.. It was a piece of cake to do.. My car runs Excellent.. I should have done a video on the repair.
@SrColon3095 жыл бұрын
Thank you very much. Very good video. 😊😊😊😊
@Oats6656 жыл бұрын
Thanks✌️
@YadielMiranda6 жыл бұрын
✌🤙
@ProfessionalDad6 жыл бұрын
how bout timing marks?
@felixamlastofmybreed46846 жыл бұрын
How many liters of oil does it take in.
@nightcoder5k6 жыл бұрын
You didn't show much. lol
@sneakerbay18366 жыл бұрын
Is there any way you could make a video on how to change the serpentine belt
@ryanlester69225 жыл бұрын
If you pay attention he does it in this
@marcfizer51015 жыл бұрын
Old comment, but you loosen the nut (17mm) on the idler pulley associated with the tensioner then use a 10mm socket to back off the idler pulley from the belt to loosen it enough to remove the belt. To get to the power steering belt, you have to remove the AC/alternator belt
@sneakerbay18366 жыл бұрын
Did you put a serpentine belt in or a timing belt or are they the same
@skip741x35 жыл бұрын
totally different things! serpentine belts, there are 2, are easy as pie to do and take abt 15 mins to replace.. timing belt is a tough job and 6 to 10 hrs depending on ur experience
@sneakerbay18366 жыл бұрын
Will this also work for 2002 milenia
@Icebreake36 жыл бұрын
I thought you push the piston back, you have to open master cylinder brake cap so that way you don’t damage the cylinder?
@bradhoff50356 жыл бұрын
Is that the cam position sensor on the lower right of the crank pulley? Looks like it. I need to replace in my 2.5 626.
@skip741x35 жыл бұрын
that is the Crank position sensor bro...its triggered by the little points on the back of the harmonic balancer pulley
@latrycewashington48126 жыл бұрын
My mechanic needs help timing my timing belt. He just put a new one on. How will he know where to line it up?
@johnnymorganjr10045 жыл бұрын
LaTryce Washington if he's a "mechanic" he should have no trouble finding out.
@skip741x35 жыл бұрын
@@johnnymorganjr1004 agreed! WTF!
@glenngarner95156 жыл бұрын
Why you have to use pliers just to take the hose thing off just to take the cover off?
@kevinvillegas22876 жыл бұрын
Quick question. I’m about to do this same repair on my malibu, why is necessary to remove the temperature sensor if you going to remove the whole bracket anyway?