Had same problem, fixed after new bougies new oil and motor flush new bobines and new injectors

This is great. I’m doing the exact same thing with my 15” Powermatic planer. Your video is very welcome.

Thanks for doing this vid. I'm about to make the same upgrade to my PM15. Especially glad you showed all the tools and your techniques!

How much to fix that?

Does it come in metric? 😊

You said there is about 1/2 inch between the double walls of the lid. The drill bit looked longer than that. Did you drill through both walls? Did the new rivets go through both walls? A shot of the under side of the lid when completed would have been nice.

What did u spray in the cilinders...?

When your lids don’t close you can shave the carpet a bit with some clippers

very nice but i dont think it will work for the bass boat guys of we run in rough water or even calm at 70?

Very cool. I think thats about what im gonna do.

Nice video! Does contact cement work better than outdoor carpet glue, I haven't seen anyone else use that for boat carpet. I have to replace my carpet on my nitro this year, just trying to find what works the best and easiest to work with.

Thank you!

The corner was awesome

Great job!!

hey does this come with a power cord? also how long is it ? thanks

Nice work! Just bought similar saw but I am missing all manuals. Do you guys have it scanned?

Wow so simple yet beautiful. Excellent workmanship. Making my first Jatoba project now, and your tips are very helpful.

Thanks!!! Great idea and design!

thank you

Why not repair from the inside and fair the outside??

This a tremendous contribution to those of us that less skilled. Thank you so much

Awesome video! Dont think I could have done it without this step by step video. So I installed the byrd shelix cutterhead yesterday and the one thing I noticed is when you install the cutterhead into the gear box bearing there seems to be some side to side play is this normal? All the bearings seem to be good. But it does seem to have some vibration. I wasn't sure if it was all the way in and didnt want to break that bolt attached to the small gear. It does spin nice and smooth. Any suggestions is greatly appreciated. Thanks Aaron.

Awsome

Epoxy!!!

Do you have an oil change video. I have a 2017 Yamaha FX SVHO and want to winterize it my self

The title is misleading - this is not a procedure for an SVHO engine.

do you have too do anything diff with a supercharged ski svho

no super too bad

That thing looks nice in that colour, Pretty sure the yellow black wasn’t available in my country

Great! Have good luck!

2021 HO models. shouldn't there be anti-freeze coming out the port on the side of the ski? to ensure that the entire cooling system has been winterized?

Nice setup but instead of going through all that trouble why cant you juat use a simple power drill and do it by hand only takes a few minutes

excellant video very straight forward!!!

Beautiful results. Do you even need to sand at all?

Good thinking getting that seal from. Honda!

Very nice video! Easy to follow. Just a quick question, when you flush it with antifreeze did it come out from the side drain also or just from the back?

How do u remove it when ur driving u boat? Like fold it down or anything?

How not to winterize a waverunner…😂😂😂

EXCELLENT video - Thanks for sharing and explaining the procedure to prepare and winterize a Yamaha Waverunner! I have watched several, and this by far is the BEST - Very thorough and informative!! I am looking to purchase a pair of 2020 Yamaha FX Cruiser HO machines and what the dealers charge to service them is extremely expensive. Following your instructions and direction, I feel quite comfortable doing it myself. I just have to figure out your antifreeze configuration and container!

You did not rotate in reverse its motion. Why? That precludes a different 'pattern' on micro surface polishing, ad allows oxides deposites to burn and collect.

Awesome video!!! Def one of the best I’ve seen for step by step for Yamaha!

Ok. Ok! STOP!! It'll totally be oversize now!!

Why not just use sheet metal screws instead of rivets?

Hello....did you built? Can i call you?

Thanks for sharing. Very helpful of you because I’ve been plumbing a while. You shared a secret. Too bad there is no flanged tail piece type of gasket for that. But this water heater has me in a bind. This thing is crazy. It’s crazy in your video so trust and believe. I called customer service. They said they would Send a technician. I spit out my drink! Hell I’ am a technician. I just have one that says lock out. Internal sensor I don’t know the first plumber that knows anything about these. 😂🤷‍♀️ P I A

Hello! I am looking into buying the same one. Now, 2 years later, are you satisfied with it? How has it been serving you?

Thanks for information. Awesome design. I modified the base with a Aluminum Slip-on Fitting Round Adjustable-Angle Flange Rail End for 1-5/8" Rail OD. Hopefully this won't give me too much trouble to fold it down for boat storage.

Very nice video. Great detail and build demonstration. Did you purchase all of the parts including thumb screws and quick release pins from McMaster-Carr?

Great job! Well thought out idea.