HP 365 here. Definitely helped seeing how to take off the head for our snapped belt. Thank you!!!!

Thanks for showing the order of the parts needed to be adjusted, cleared or removed before the belt repair is made. During the video the print heads were removed. After the encoder strip was put back, that was the end of the video. Is there a specific procedure in putting the print heads back into the carriage?

Thx for this video - today, I did not change just the belt but also the M3 screw, which secures the left tip of the encoder strip. I trusted that there was a corresponding thread behind a 13 mm width across flats. Unfortunately, the assumption was wrong - Knaaack!

all my ink catridge missing, latex 365, how can i fix it sir?

Hello, i have change the belt but i have recived error 86:01 - and the ink cartige colector ejecting him self? if it is posible can you give me a hint?

Hi, how to introduce the number of the new sensor in the service mode in plotter, the service mode is protected by password. Do you know what the password is?

Hello guy, pls you help me something. Is there parameter to be set after finish replacement? Or it can be used immediately? Thank you very much.

Hello mate. Is it also just a matter of replacing the ink cartridge if its faulty?

my hp 335 not printing as per file size. print is much more shorter than the actual print size ..plz help

This video does not show anything wort mentioning. It is the worst video I have haver seen. You can't see were he is losing all the screws and how he is putting on the tension belt back in the bottom of the Carriage Assy

You the GOAT fr 🐐❤‍🔥❤‍🔥

How do you access the enginer service menu ?

nice video!

Have you ever changed the hp latex 570. 3L connector. It says i have leaking at the tank side.

Hi Casfer, I have been dealing with a 86:01 on a Latex 370 for about 2 months now, supoosed paper jam there is no media, I am suspecting Axis motor but that was replaced along with belt and 3L PCI about 2 years ago,I have checked encoder strip and tensioner. Could you please help?

can you tell me what type of fabric is used in the L330 printhead maintenance cartridge? I would like to change only the tissue and reuse the cartridge again

I didn't see you bleed the air out the ink line. ???

Casfer, let's say 3 of the ink tanks dont recognize them. And there was no error at the printer. Could it be PIP issue?

Thanks. The HP 365 service manual under 'Belt Assembly' also has this process step by step.

hi! i have a problem - my latex 570 keeps printing in the same spot. the media does not move well while printing. it loads ok, moves it ok. but when i need to print - it doesn't move. only if i use TUR and if i help it with my hands. You know when it can be?

How far apart do we space the metals on the belt so the cartridge moves and does not get jammed in placed?

Hi, well I also just want to say thank you and ... fire that cameraman 🙂

I changed the PIP sensor Cyan one. I did everythjnf correctly then i install thr samr ink cartridge. It did not recognized. Do you think it is the cartidge chip or there is some other issue?

Can you make a video for cleaning all the curing unit including heaters from dust?

cameraman….😢

Hi Dear, First of all I want to thank you for the videos, its really helpful. I have a hp latex 360 and getting the error 16.42:10 Module 2 ( right to left) faulty or not connected . Line # 1403 . I was wondering if you know what is the part number or any suggestions. I would appreciate. Thanks

sir i'm crying why the hp latex 375 machine has an error and the code 25.1:10 appears

sir i'm crying why the hp latex 375 machine has an error and the code 25.1:10 appears

sir i'm crying why the hp latex 375 machine has an error and the code 25.1:10 appears

Selamat malam kak Ada yang mau saya tanyakan

Greetings am from Zambia looking for a belt for z6200 designjet machine or any recommendations where I can buy

👍

What he don't show or tell you is that it takes two people to put the encoder strip back on and the spring tensioner only goes on one way. there is a slight offset with the screw hole. So when you have the carriage upside down putting the belt on, the tensioner spring must be facing down so when you flip it over you'll be able to see the spring open side. Still thanks for posting this video, It did help!

great video thank you had to replace my belt came out good

I replaced the pip and the printer is still showing the error message when I power it on? Any thoughts on how to resolve this issue? Thank you

Please do another video next time you replace a belt using a different camera person. Who ever recorded this video probably had so attention disorder or clueless

Can you make a video on replacing the foam pads the two small ones for the head

Hi brother, can I have an Email to contact you? I need support for my Latex 360. Thank you

Can you do one on color sensor replacement. Please!!

hi can you help me how latex 315 error code14.87:10 and14.83:11

Why did you replace the fan? My 560 is bunching up the substrate and causing head crashes… the material heats the curing tunnel

Raphael Philip Do you have a similar video for the L25500. I need to know how to separate the ink lines from the printhead carriage. This is where I am stuck. Thank you

Would you post a video of you removing the cover? I believe I have all screws out, )except one and it is super tight). Thanks

I cannot get the cover off of my printer. Is there a trick to that? Seems like the top screw inside the cover won’t budge.

Great Video, I replaced my HP 360 belt myself with a new belt and pulley from eBay for just $165 - Thank you

Hi, I have a 42:10 error. I checked, cleaned, and oiled the bar. But there is no issue. I believe that is the solution to what you have done. Do you think is there any other thing that might cause it.

1- How to clean hp latex 381 printheads manually? 2- how to repair them? 3- how to keep them well? Any manual or video? Thank you so much.

Hi Dear 26.1:10 Error Code, I replaced the PIP, but same error. Could you please help me resolve this issue?

Perfecto, Casfer, pude cambiarlo solo con tu excelentes videos Por favor enviar mas videos Abrazo