@mugsythetallone6852 3 жыл бұрын
Thank you so much for posting this.
@soyebravat8903 2 жыл бұрын
Can you make a video on replacing the foam pads the two small ones for the head
@jimidero Жыл бұрын
Can you make a video for cleaning all the curing unit including heaters from dust?
@giftedwrapzaz2559 2 жыл бұрын
I replaced the pip and the printer is still showing the error message when I power it on? Any thoughts on how to resolve this issue? Thank you
@Mark-im7vm 9 ай бұрын
Hello mate. Is it also just a matter of replacing the ink cartridge if its faulty?
@trenthines26 2 жыл бұрын
I cannot get the cover off of my printer. Is there a trick to that? Seems like the top screw inside the cover won’t budge.
@jimbow3274 Жыл бұрын
I didn't see you bleed the air out the ink line. ???
@sainathdhanrajkokane 9 ай бұрын
my hp 335 not printing as per file size. print is much more shorter than the actual print size ..plz help
@johnroberts8237 2 жыл бұрын
Can you do one on color sensor replacement. Please!!
@casfer4998 2 жыл бұрын
Hi Robert, there are only 2 screws(T10) holding the color sensor from the carriage, plus the flat cable connected on the carriage pca.
@trenthines26 2 жыл бұрын
Would you post a video of you removing the cover? I believe I have all screws out, )except one and it is super tight). Thanks
@Productionwrapsandgraphics 10 ай бұрын
did you get the cover off? Can you tell me how you did that?
@harisalfaza642 Жыл бұрын
Selamat malam kak Ada yang mau saya tanyakan
@rahmigokcedag4895 Жыл бұрын
Casfer, let's say 3 of the ink tanks dont recognize them. And there was no error at the printer. Could it be PIP issue?
@casfer4998 Жыл бұрын
If there is a problem with the PIP sensor it should show error. Are we talking about 3 inks tanks the same color or 3 tanks different color? What is the model of your printer?
@rahmigokcedag4895 Жыл бұрын
@casfer4998 3 different one m, lm and lc and there is no error.
@rahmigokcedag4895 Жыл бұрын
It says missing cartidge even though it was installed
@casfer4998 Жыл бұрын
@@rahmigokcedag4895 did you try change any of them? Which printer model do you have?
@casfer4998 Жыл бұрын
It could be just defective cartridges but it is strange to get damaged 3 cartridges at the same time. On the printer panel you will find system error and system warning, check the codes on it.
@harisalfaza642 Жыл бұрын
sir i'm crying why the hp latex 375 machine has an error and the code 25.1:10 appears
@rahmigokcedag4895 Жыл бұрын
I changed the PIP sensor Cyan one. I did everythjnf correctly then i install thr samr ink cartridge. It did not recognized. Do you think it is the cartidge chip or there is some other issue?
@casfer4998 Жыл бұрын
Hi, did you input the new PIP Calibration value? What was the error before you change the PIP?
@rahmigokcedag4895 Жыл бұрын
@Casfer i dont know that value setting and where to do. I had 25.4:10 Cyan Thank you by the way. I have been learning a lot from you.
@casfer4998 Жыл бұрын
The value is actually written on the new PIP. It could be your IT tank or ink cartridge is already damage as well.
@rahmigokcedag4895 Жыл бұрын
Got it now. Looks like the previous sensor burned the chip out. New cartidge works well. Thanks
@Paliony777 9 ай бұрын
Where do you input this values to? What menu option?@@casfer4998
@leszeknowak2760 8 ай бұрын
Hi, how to introduce the number of the new sensor in the service mode in plotter, the service mode is protected by password. Do you know what the password is?
@leszeknowak2760 8 ай бұрын
It's HP Latex 330
@khan2107 2 жыл бұрын
Hi Dear 26.1:10 Error Code, I replaced the PIP, but same error. Could you please help me resolve this issue?
@casfer4998 2 жыл бұрын
Did you run "Recover broken bag" from the Diagnostic. If yes, then check the IT cartridge, otherwise you might have a problem on the ISS board. Look for any ink drop on the ISS. In case it does not help, look for authorized hp tech in your region to help you sorted out the issue on site.
Фани Хани
Рет қаралды 1,2 МЛН
Harley Quinn with the Joker
Рет қаралды 6 МЛН
Meine Mechaniker
Рет қаралды 95 М.