MBS Lock Hardware Tutorials

Пікірлер

@shadroid 2 ай бұрын

Not directly related though a passing mention of how to replace the cap on the top of the barrel would have been in order.

@user-ll7zx8qr7y 4 ай бұрын

I hate to see a lock butchered like that.

@CharlieTrusky 4 ай бұрын

What happens if you turn to the right

@user-we9pp9lc7w 6 ай бұрын

What is the subtraction number for an A4 system?

@killer2600 6 ай бұрын

This only works if the cylinder was properly combinated to exact A2 specification. If someone chose top pin by "good enough to work" standards then measuring the top pin won't work.

@javiermontoya8032 7 ай бұрын

This helped. Thanks!

@Chirael 7 ай бұрын

This was very helpful. I was searching for a while in vain to try to find a video showing how to re-hand or reverse an SFIC door knob (where the core was upside down and driving me crazy), and you explained it perfectly. Thank you so much.

@SebastianDiPalmaVampyre 7 ай бұрын

Ad a veteran locksmith of 39 years as well as an instructor in two different schools I am horrified by the ignorance and just plain wrong of videos like this.

@kylekelly1215 Ай бұрын

How would you go about doing it?

@SebastianDiPalmaVampyre Ай бұрын

@@kylekelly1215 5/32" drill bit right at the point of the figure 8 takes out the retaining bar, you shear off the the retaining bar so when you pull the core, you can decode the pins if needed.

@infinity157st 8 ай бұрын

Store room function should always be locked from the outside!!! Class room function could be lock and unlocked it for the whole day then locked it.

@DancinFool Жыл бұрын

Good video. The screw at the end is a great idea. What size bit ?

@user-wy9ys8wh3w 6 ай бұрын

Careful about putting a screw in there that is very big. It will distort the core and cause it to expand against the housing and make it a real bear to get out. Same actually goes for pressing really hard with a big drill bit like the one he's using in this video. Best to use a 3/16" imho. If you drill straight then you can turn with a small screwdriver, no need for woodscrew. If you need woodscrew, you maybe want to use small diameter or drill a pilot hole.

@doorandlocktips Жыл бұрын

They’re not called Barros they’re called Chambers ha ha😂

@keepercoach Жыл бұрын

Why not just vacuum it out ?

@markklossner8740 Жыл бұрын

How would you decode the control key for an A4 system? What number would you subtract from to get the key cut?

@SadSam69 Жыл бұрын

Why do you use the number 13 can you please explain that

@princesssmile7958 Жыл бұрын

Where I can get the exact same lock you installed?

@rubenbalbasgarcia9207 Жыл бұрын

At least, a straightforward explanation. Simple and clear. Congratulations! I very much appreciate it

@kurogane2x Жыл бұрын

First i thought this was going to be an attack on a sfic stuck in the lock due to no conkey lol

@kevenquinlan Жыл бұрын

Thanks. Super simple explanation. You should make a series of videos where you decode a lock for operator, control, and master and how it's done.

@geraldskinner63 Жыл бұрын

Thanks!!!

@khrisendatramjit4308 Жыл бұрын

Can I use on my front door

@bigandfluffy2000 2 жыл бұрын

Does this work if the lock has been locked from a failed pick?

@craigcurtis8744 2 жыл бұрын

Use a flat blade screw driver just inside the lip of the drilled hole to pry the front cover off the core. Then you can access the locking cam and clean out the channel the locking cam needs to move into.

@Raven-qj9gv 2 жыл бұрын

Very nice , thank you. !

@raywiblelocksmithphilapa8766 2 жыл бұрын

Just pick it to control

@rafaelmolina1903 2 жыл бұрын

a storeroom door lock can be fix it to use as regular door lock?

@infinity157st 8 ай бұрын

No it can’t be change not fix change

@thomasvu6951 Ай бұрын

@@infinity157stis there a lock that can be fixed to a regular lock? So storeroom lock some times and open during other

@LeoS41280 2 жыл бұрын

You really beat up the rim cylinder removing the core.

@Unknownlifters 3 жыл бұрын

Thanks for guidance

@poppydream5557 3 жыл бұрын

Put a blank key in there to raise all the pins. It'll make it so you drill through all of them at once. If you're accurate you can use a 1/8 bit and use the key to move control arm. Happy drillin!

@2815Juan 2 жыл бұрын

I’m pretty sure the bow of the key will be in the way to drill straight in

@craigslitzer4857 11 ай бұрын

@@2815JuanI've had to drill one out recently. It will be if you're using a standard Best blank. You will want to bend the top of the bow over, or cut it clean off so that it's not in the way for the drilling process. It also makes it easy at the end, as once you've drilled to the shear line, you don't have to clean out any debris. It's ready to spin the control lug.

@dennischausse3075 3 жыл бұрын

I understand but why is 13 the magic number

@kenchilton 2 жыл бұрын

It is due to the distance from the cap to the control parting line and for the length of the spring. The total stack in A2 is 23, and the distance between the parting lines is 10, so 23-10=13, which is what is left after the bottom pins, master pins, and buildup pins get the chamber up to the control parting line.

@philippaasch9126 3 жыл бұрын

All I hear is your smacking. Sounds like you’re sucking on a piece of candy.

@parochial2356 3 жыл бұрын

Another question: all of the vids I have watched show the use of a 90 degree pick to remove debris. Why not use compressed air?

@parochial2356 3 жыл бұрын

At the beginning, you say to measure the depth of the core before drilling, so as not to drill too far. How do you measure the core before it is removed?

@idkidk4334 2 жыл бұрын

You keep a separate core in your inventory

@craigslitzer4857 11 ай бұрын

Assuming you've got a key (doesn't have to be a working key) you can also measure how deep the key will insert into the cylinder.

@stephanies.9786 3 жыл бұрын

Helpful and informative, thank you!

@500jan 3 жыл бұрын

Drill out a dead lock

@chestercallahan8856 3 жыл бұрын

Great video, my boss showed me a different way and your way seems to work much better for me. She would drill slightly lower and pull face plate off and never clean debris but could always make that work like it was nothing.

@raymondwest1973 3 жыл бұрын

How do I remove the core?

@DVS-ANIME 3 жыл бұрын

What if your top pin is a 14?

@kenchilton 2 жыл бұрын

Then it is not an A2 system or the lock is not a BEST style. In an SFIC with A2 numbering, the length of the spring and the distance from the control parting line to the cap are fixed dimensions that make the longest top pin that reliably works a 13. Longer pins are only used for buildup.

@stevendiemer7854 3 жыл бұрын

Thanks, just the answer I was looking for.

@maryproveaux9200 3 жыл бұрын

Is there a non-key retaining puck lock with hasp? I bought the Abus and it is key retaining so I can't closed the truck door unless the lock is locked and then I need to get in the truck through the passenger side. fyi, someone broken into the box truck and destroyed the lock, it's totally gone. thanks!

@noahway13 3 жыл бұрын

Duh... I wanted to know what is different INSIDE. What mechanism makes them act differently. And I'm FIRST. Nice video for very basic learning.

@lockpremium9826 3 жыл бұрын

About how to decode the master key bitting?

@faradaymaxwell 4 жыл бұрын

How do you get that icore out to do this , with out the control key?

@johnholding107 3 жыл бұрын

That’s what I would like to know as well.

@idkidk4334 2 жыл бұрын

This is for if you pick the core out of the lock/housing, I had to pick one out then I reverse engineered a core key so I can reuse the housings. Have a keying block, a sfic kit, key cutter, and the wall of key blanks

@craigslitzer4857 11 ай бұрын

@@kenchiltonI recently took over a set of locks and although most of the paperwork is available, not all of it is. So far I have found 3 different controls and am aware of a 4th. I've only had to drill out one lock so far, but will probably have to drill out a lot more before I'm done. Hoping to minimize that, so I'm considering learning to rake & pick.

@SantiagoDonate 4 жыл бұрын

Ty for your time broh

@gurfatehphilsingh4049 4 жыл бұрын

Nice and Informative. Easy to Understand.

@miladmaani 4 жыл бұрын

Thank you for the video, Where can I get the same lock?

@jesiahtyson6646 3 жыл бұрын

I know it's pretty randomly asking but do anyone know a good place to watch newly released movies online ?

@reeseclyde5907 3 жыл бұрын

@Jesiah Tyson Lately I have been using Flixzone. Just search on google for it :)

@bigbrother9531 4 жыл бұрын

Wake me up when its over

@ZinniaBookwala 4 жыл бұрын

Both the classroom and storeroom function lockset are similar that there is free egress from interior at all times and have a keyed access from the outside. Is the difference that-while Storeroom ALWAYS requires a key to enter from outside, in a classroom you can choose to leave it unlocked or locked using the key?

@tonks8687 3 жыл бұрын

I think you are right.

@stevemartinism 4 жыл бұрын

Made it simple to understand. Thanks for sharing, stay safe🇺🇸

@rituallime8587 4 жыл бұрын

Can u find a change key the same way just with a different equation

@kenchilton 2 жыл бұрын

Yes, sort of. If it is master keyed, you will be able to identify many keys that will open the lock this way, but you won’t know which are the masters and which is the change key without decoding more cores.

Ең жақсы KZfaq

Пікірлер