Thanks

What oil do you recomend for my Mazda 6 2.3 engine 4 cilender

How do you get the pully off that goes to the alternator

how much oil need to used on my mazda 6 2005 motor 2´3 i am waching you from all the way from tijuana south border and what oil you recomend for the transmission keep it up good videos good info

Is this the i6 engine?

I would like to know what car you are working at? Is it a small 2,2 Diesel 4 cylinder, a 4 cylinder 2 Liter petrol, or a 3,2 Liter straight six petrol engine? Also, I have absolutely no idea of where to look for the drain plug on mine, nor the extra drain plug on the engine block (or a tube there of)? In your video, you show a very narrowed down movie shot of the radiator drain, but where is it? On the left side, right side, fromt of rear? Kind regards.

Commenters are right you should just say w is for winter flow period and put it at that

I have a 2008 f150 xlt 5.4 triton 93 thousand miles it has been take care of will hurt to use asmoil Ford recommends 7500 oil change and do yu have use a special oil filter I'm a veteran on disability how does it cost .I enjoyed yur video. Sarge Veteran. God bless.

Do you always have to change the filter? Had a loosened drain plug so I had an oil leak. Should I just add oil

How the hell did you reach in to disconnect the power cables from the ac compressor??

I learned

Can you pls tell me the gasket code…!!! Gear oil pan gasket

Hi my mazda 6 has leak the fluid comes out to the hole do u have any idea why oil coming out

Hi does your mazda has hole in the transmition

For the definition of viscosity you used the means of measuring the viscosity of the oil lbs

does this transmission need to perform transfer case fluid change?

My wife's 08 LR2 just had this happen to hers. I'm ordering parts to fix it myself and wanted to see if you had to replace the Serpentine tensioner too or can you just bolt the new pulley to the existing tensioner? The part I'm talking about is LR004667. Also, did you end up replacing the Idler pulley (LR005993) which you say needs a special tool? Not sure if I should replace this or not?

To sum up viscosity in two ways: - A definition I learned in Marine Engineering is, 'a fluid's inherent resistance to flow at a certain temperature(usually calculated in kelvin). - You can also break it into basic physics units. Viscosity is a covered area, per time taken, multiplied by density; which is a certain mass per volume. So a Mass of fluid x Area covered(say the circular section of a pipe) / Volume of fluid passing over your reference Area in a given Time. I think though once you tell someone molasses and honey are viscous fluids, and water is not, they get the point intuitively lol. Awesome video!

Useful, appreciate u sir

Thanks for the video..very helpful to see that it uses a rubber gasket. Yes , fluid level should be checked warm,,at running temp ,, With the engine running at the time. Drain and fill usually takes about 3.1 litres.

it's hard getting to the bolts even with the squiggle socket

how can you reach the bolts above the sub frame... my car is 07 5AT version, it's impossible...

Did u ever make a video showing the reassembly of the land rover lr2 serpentine belt?

The part you had a hard time with is a press fit, just give it a nice tugg and it will turn loose. The. To reinstall just line up the rubbers with the already installed hex bolts and push on firmly until it is seated

Sorry but a very poor explanation..I am none the wiser.

Really simple explanation/demonstration. I like your calm tone and manner, easy to listen to and makes the job not feel daunting even though I am an amateur. (I still may not do mine myself though) 😂

Is the 4 speed transmission filter the same as the 5 speed?

thanks

How many miles when pulley went bad?

Thank you for taking the time to share your knowledge.

So one of my options on a newer vehicle for me was a 2008 Land Rover and your vid was informative and helpful, thank you very much, I also have a Chevy second vehicle, maybe do your Chevy next?

I have a 2008 HSE with 185k Miles. I love it, some minor issues here and there. A big issue was the transfer case at about 170k miles. I believe it was caused by using rubbish tyres. They still look great, I have taken care of her. Make sure to treat them nicely with maintenance and you will be ok.

do you have any advice for a mazda6 with car running only on 3rd and 4th ?

Very good video, loosening the fill plug first in case of a problem you still have fluid in the diff rather than draining and not being able to re-fill. What could happen? Murphy's law of something breaking or stripping out.

I'm about to change the belt on my 2010 LR2. You confirmed my fears. Lol

Hey Ventre: You did not list the funnel brand. Looking for one that wide. Do you have a brand or link to that funnel? Also, you showed a nice video of removing and putting back the skid plate, but you did not video the really hard parts (like on how you routed the hose, how you opened and closed the radiator petcock valve). That's where the real hard fun begins -- and that's the part that should be on video. Have a 2012 LR2 and I tried to do exactly what you did. The radiator valve turns only about 90 degrees, and no fluid flows. The hose is not easily routable. Had to loosen the plastic mud guard over the left front wheel to route the hose. As far as getting to the radiator valve, had to remove the bumper liner and so on. The sections that were not on video are actually the hardest part of the job. Recommend having the camera rolling throughout the entire job. Not just when removing or installing the 6 bolts on the splash guard. And you would still have the incorrect mix in your system because you ran water through the system to flush out the old fluid. Better to add some "full concentration" fluid to balance coolant back to 50:50 mix. A cheap hygrometer test (less than $10 on amazon) would do the trick. I know this from the experience of flushing other cars exactly how you did it (which is not a bad way to do it). The only difference would be to add 1/2 to 1 full quart of pure concentrate to correct the mixture.

Where can I find the replacement hose

What type of fluid did you put in. Type and brand?

What olí you recomend for my mazda rx7 fc 1987 1.3 b

12k for an engine??? Wow...and I thought Mercedes was bad.

Serious question is it ok to reuse these oil pumps?

Can't you use Vaseline in place of dielectric Grease?,

You did a mistake looks like, first you say higher number more lubrication then you say as it warms up lower lubrication... Something is not adding up in the vid, please cgeck what actualy you said

Great review. Thanks

Great video

Nice Job, but corrosion needs to get some work out. I can recommend to brush all underbody with once boilef lienseed oil. Cheap but perfect. This oil is very small molecular particled und coats all so corrosion will be stopped at once. In Order tget the Surface quicker dried out you would need to boil it once and than paint or spray it. Easy almost no costs effective

Will this be the same for an 01 1500hd?

Do ineed silicone sralent

Love the use of the torque wrench!!!

Your music is so loud compared to your voice. Informative but...clicking away. Annoying!