Sig P320 Flat Trigger

I love pastrami.

507K-GR X2. Direct mount, no plate.

@@AllenTam thanks for sharing bless you and your family good shooting

I know it has lens covers. I ran it on my MPX for a couple of years before I bought the 2nd.

I don't want to mislead anyone. The worst thing I can do is make a video and lie about my first impression and experience of a product or service.

I did. The CS sent me the label the next day, and I sent the frame to them immediately. The SC told me it would take two weeks. My frame was sitting on their shelf for six weeks before they took one day to replace the ejector. It then sat on the shelf for a couple more days before they sent it back to me. Altogether, it took seven weeks to get it back. They included the work order so I could see when their gunsmith started working on my frame.

@@AllenTam that really poke guy but at least they did replace it. how's it go after the repair? i wanna know coz i have the emp3 original and hope that thing runs well

@@Larry-ds6ib My 3" Roin guide rode walked out on me during the first two hundred rounds of break-in. I think it was the first two hundred rounds or three; I don't remember. Anyway, I didn't notice that until I got home to clean it. The rod barely hangs on the base/plate with just half of a circle turn. If I had brought more ammo with me, I think maybe shoot three or four more rounds, and the rod would have flown out to down range. I use red loctite to make sure it will never unscrew itself again. Be sure to check your guide rod and watch it during your break-in. Oh, and the wood grip screws all walked out, too. I can turn them with just pressing down with the figure without using screwdriver.

@@AllenTam thanks for the advice man and i will look into mine and make sure that goes purposedly

I was eyeballing one from a CA store, too. But I have a hard time justifying paying so much for it. I'm sorry, but I'm not familiar with EGW. I'm running Atlas Gunworks toolless guide rods on a couple of my 2011, a 4.25" Commander. Their toolless guide rods work very well, and you just reminded me to order a couple more for my 5" and 4.45" Roin. I have yet to see anyone make a 3" toolless guide rod anywhere. If I do, I will get them. Thank you for watching.

@@AllenTam check out EGW 1911 guide rods, they do have at least one for 1911 officer model and someone said he used on his EMP3. lol I wanna try but let me play w/ mine first and see. Thanks a lot bro!

@@Larry-ds6ib Its not tool-less. That's replacing something with the same thing.

I don't remember. I bought most of the parts below retail. With tax and shipping, I want to say under $1500.

@AllenTam okay thanks great build by the way

kawvalleyprecision.com/product/kvp-mach-3-modular-linear-comp-body/

I made over 100K a year as an designer in animation industry just pushing pencil having fun drawing shit. How about you, how hard you have to work and much you made per year? I don't buy expensive shit just because they are expensive. I put careful thought and research into them before I buy anything I put on my guns.

@@AllenTam yeah right, i bet you did. Your optic says poor as fuck

Every item's company name is in the video. I took time to show them.

I got them from Container store.

The slide is XCompact/Subcompact. The barrel is PMM Subcompact. Don't remember the barrel length. PMM threaded barrel is shorter than the Sig 4.3" XCompact threaded barrel.

17. Now I'm running with Strike Industries magazine extend increases the capacity to 22 rounds.

I am not a firearm expert, and I don't pretend to be one. I consider my skills at the elementary level next to nothing. But I know enough that the mainspring housing is seated flat with the grip. No amount of force from the hammer spring will push the mainspring house downward. For the same, releasing the hammer will not allow the mainspring housing to move upward because the mainspring house is secured in place with the pin. So, how is it possible that installing a magwell will push the mainspring housing up? Both magwell and mainspring housing use the same hole in the grip. If the magwell caused the mainspring house to move up to pinch the grip safety, that's a lot of upward movement! If that happened to some people, for them, the problem is not installing a magwell. The problem is that their grip pinhole is so severely worn that it allows the mainspring house to move up and down; their grip is junk at that point. But again, I am not an expert; what the hell do I know, right?

Not every pistol has that issue. I went back to the shop to check; the ones they have in stock don't have that problem. Several weeks ago, I saw the shop had a Black 4.25" used one for sale. I tested it, and it has the same problem. I guessing the original owner didn't want to deal with that problem and sold it. I was going to buy and fix it myself, but someone had already purchased it online. A lady came over to pick it up about 5~10 minutes after I looked at it. I wonder if she know about that problem?

The owner told me that because 2011 had tight tolerances, coating inside would cause fitting issues. I told him that if you recoated it on top of the original coating, the fitting would be very tight. But if you strip the original coating off before applying the new layer, how would that have fitting issues? The owner has yet to reply. That led me to think that they don't strip the old coating off; they recoat on top of the original coating. I don't want a coating service like that, so they are not getting business from me again. Nor would I recommend them to my friends.

I like these guns but they should switch for a better finish option like a salt nitride. I’ve never considered cerakote a real finish for a firearm

My mission was to purchase a manual safety FCU, whether an M18, M17, or whatever came with the package; if it had the Manual safety FCU, I wanted it.

I have held a tungsten-infused grip before, and it is not much heavier than the plastic, so I don't need to spend money on the weight; the grip weight is not going to do anything for me, I think.

No, sorry, I didn't think about that.

I'm eyeballing P320 Legion, too.But something else I want to buy first. Anyway, that's one more reason for you to get out of CA. 😆

I wrote a review with picture; I am not doing business with them again.