Hey!!

Definitely the best instructional video I’ve seen thus far. And one other guy in the comments said about having the middle cross timbers being and little longer than the pvc,too give room for it too spin

Looking for something to build and I couldn't even finish this video. I hope you can do another 1 when you're not so high and know what you're doing lol just saying

Great idea

Make sure the middle support pieces are cut quarter inch bigger then the pvc. That way it spins freely and you get the full potential out of your dog! Good work homie!

I know this was a long time ago, but thanks for this. Dog controlled treadmills are expensive.

i know this was 10 years ago but about how much was this?

Make sure you monetize this video it’s great

The only guy showing us step by step instead of “look at what i built”

Playing jigga in the background

Could we know exactly what you used to build it

Dope bro

What is the length of this treadmill?

Good one!

Hello. I live in Russia and reached your technologies 9 years after your video was released)))) I will do the same design. Thank you

Great music for a great dog from an awesome owner

That Nicki track

How did it turn out

It is great! Sweet dog 🐕

I know this video is old. But I recently got a dog and. Wanting to make something similar. And was wondering how it ended up working for you and your dog? And was there any changes you'd make?

did it work? where's the sample video?

The fact he built it with a mixing drill though 👌

Thanks man I have been trying to figure this out! Perfect. Big help!

Whats up.. how did you tied down the carpet

I'm not going to read all the comments, but in case it would help anyone moving forward... I'm a perfectionist so those lag bolts have to be seated or I wouldn't rest. A spacer or a a couple washers between the frame & the rollers & you can tighten them lag bolts on down. Lol

Woodglut is a solid company with solid woodworking plans.

It is not the bits. You needed to pre drill.

Can you post the wood measurements?

Helped a lot thanks

What size was the landscape timber inside the pvc pipe

Que tela le pusiste?

12:40 *BAD YOU*

Do you have a list of materials

When doing the carpet belt is it better to have it loose or tight?

Here is a tip install skateboard bearing into each end of the roller for a nice easy quiet operation bearings on amazon are about 5 bucks.

THANK YOU for making this video.

I got bad news for you little buddy. You can’t patent a mill”. Carpet nor slat. It’s considered agriculture tool ... farmers used it for many things. Including electricity. I had to explain this to Trotter USA. When he tried to sue HF Mills. Or a Jenny, Turtable Etc. Better luck next time. By the way. That design has already been done. I actually have a blueprint for it.

He speak english or wath ?

How did you join the carpet

I can’t understand what you’re saying 😭 I have no idea what you put in the pvc so it’ll spin

It would be a life saver if you could sell it in pieces with directions I’m interested

do you think he ever got it out of the front room when it was built

Where did you get the carpet?

how did you make your roller

Abi ben de aynısından yapicamda türkçe olarak yazabilirmisin neler kullandıklarını ve kaça kaç olduğunu birde o demir çubuk ne olduğunu da yazarmısın ben KZfaq den çeviri yapamıyom

How much did it cost to make and can I get the list?

Nice job bro great video 👍

Upload running video of dog on this carpet wheel/tread mill

Thanks for the video it helped a lot but instead of landscape Timber I used 4in. Wheels ...I found at the hardware store put them inside the PVC piping and I use carpet tape for the carpet Had my pup on it but it's going to take some work for him to get used to it do you have a video on how you trained your dog to get used to the mill

if yoI was using woodprix instructions to make it and I did it already :)