The screammmmmmss

Excellent video. Best one yet for removal although I used a socket extension 3/8" catching an edge of the bearing apply force with a screw driver then hammer extension.

you should never hit a bearing with a hammer.

Cool build man.

i liked the video when he gave the bike throttle and the gas tank collapsed

Where’s the exhaust from?

I saw that at Talladega a few years ago lol

intresting i just blew up my 250r but i guess i was screaming it too often do you know whether it might be a top end rebuild or bottom end before i tear it apart

Good way to go to the er

Clutch is smoked!

What header is that and from where

hey do you remember if all the clutch bolts are the same length?

Would have kept that motor and sold it for new parts but fun is fun

Man i hage a doodlebug wuth a 97 and it ket me go 34mph and is like 25+yrs old, if j get my 212cc then ika put that engine in a bicycle

Where does the smaller ring goes does it go on first

Yeah those filter suck i had them on mine and those kept on killing the engine I took them off my bike runs 10000 percent better

Good job thank you

Wow I have a g29 setup that looks exectly like yours!

Why didn’t you show me how to put the clutch plates and discs in? Duh!

Hey man, I love this exhaust note, I was wondering if you could share what your complete setup is to get it to sound this good? Thanks

My husband cannot get this bearing out HELP

I just got my dirt bug frame stolen

My crf 2013 450 r blew up yesterday, came to your page to look at this bike. My crank shaft won’t move at all, I hope I don’t have to do too much to get it running again

Now that’s what I call a blowjob!

I hate break it to you but that piston and top end will fail you in 6 months I recognize that piston That's the same Chinese piston we ran in my blaster and it lost compression quickly it actually wore two perfect grooves in both sides of the cylinder

This video is almost useless unless you link the bearings used...

Do you have a link for the header pipe??

Can 3 monitors fit on here

Thats a 55 inch dumb dumb

Where you find wheels at?

Can you send the link for the exact bearing? Idk what size to get and I need one fast

wow

So do you necessarily need a drill for the bottom

I have the same bike and my brakes don’t work they only work when I push the bike backwards how come

What is the with of the table

Nice job! I'm in the process of Restoring One Right Now that I got for free! Question, does your back sprocket have 5 bolts hold it too the wheel?

Good work brother 🤙🏻🤘🏻🫡

Does it have height adjustment?

1:56 the non-hemis are better for modifying anyways, you got the right choice.

i have a simillar sixed pc from what it looks like so do you know if it will fit a 33x11 ouspad and still have a good amount of space to fit everything else

What did you use to punch the bearing out, I have the same problem like you, the bearing fell apart on the sprocket side.

The spring is right

And kill switch not saftey thing

The fly wheel not the rip string

Never mind it was the throttle not the clutch

Yours was worse than ours. Ours came with brakes a rear tire brakes a rip string an engine not even all of it a clutch thing a button starter for saftey or somethin like that. It didn’t come with a bit of the engine the front tire and axle and no air in the back tire. Good thing is it came with the chain.

I love how he stopped to support the great American in the back ground doing a pull 😂🫡

True story: i gave my doodle bug to my brother for his birthday this year since hes only 12 one day he says he hears a little knock coming from his bike and doesnt know what it is. Since it was due for an oil change i changed it and it seemed to still have a knock but very lightly after that i took it for a spin since i wanted to make sure it was good to ride and so far it was great but as i got maybe 3 minutes into the ride i notices the bike got slower idk how but maybe a few seconds after i hear a loud pop and the bike starts to slow down as a pain started in my leg. I look down and noticed the spark plug was completely gone completely like zero trace of it and my leg got hit by the spark plug which is crazy considering that the plug was torqued down exactly like it was supposed to. I get home and try a different spark plug and notice that all the plug threads on the head are completely gone like wtf.

Great work on the Doodlebug!!

We’re did u get that Graphics kit