Excellent video. I’m sure you’ve helped a lotta folks just by these explanations. And you just did it! Thx
@brianmiller44665 күн бұрын
I love your channel. Been following since i fired this money pit up. Anyway Ive been having wild afr readings from th TermX’s o2, which is backed up by a stand alone PLX meter(albeit a lil latent with data transfer even w sample turned all the way up) reporting to my digidash. Still im assuming its a bad sensor. Since i cant find anything definitive please, PRETTY PLEASE! Can you tell me will a holley 554-100(ntk sensor) work with. TermX? ANY help wood be fabulous! Most sincerely @meye wits end in Mi
@philippelefaix86746 күн бұрын
Hi Joe, i am Philipp in France. i appreciate what you show here.....i need help: i bought a sniper 2 one month ago from EFI systempro, after a mistake, i tried to load a file from my sniper 1 to my sniper 2 : result : i lost my ECU : message : ECU OFFLINE, and i don t know how to recover my ECU, i wrote to scott from EFI : he don tknow, i wrote to a tech support at Holley: Matthiew richmond : he does not answer me anymore, EFI systempro don taccept to refund me, he don t help me, holley don 't help me, a friend of mine did a post on HOLLEY forum " sniper 2: ECU OFFLINE".....no solution.....i am lost: do you have a good adress where i can explain my problem.....i check all : upgrade, firmware, main harness : all is good.....thanks a lot Joe to tell me what do you think about this.Philippe ( Orléans/France)...here what i did this week : kzfaq.info/get/bejne/edtzZNqqzZnanIE.html
@horsefly10206 күн бұрын
I just fired up my ride over the weekend using a sloppy tune for start up. It idles good but stumbles and sometimes dies unless i roll up the throttle real slow to ablout 1200rpm then ots fine. It also doesn't want to start without pedal when it's up to temp.
@jimbradd27836 күн бұрын
How can I get in touch with Joe?
@TheMykkH7 күн бұрын
What part of the TermX is the butthole?!
@NaeemNaeem-do3fz7 күн бұрын
Excellent and very very informative
@Khalidsvt1017 күн бұрын
waste of a cobra 👎👎
@trans7678 күн бұрын
Hey do you tune remotely
@dalton551710 күн бұрын
great video man you know your stuff
@lukesimeon575610 күн бұрын
Well put Joe... good thorough tuning is worth every dollar... I call them quick tunes...cookie cutter tunes...
@LateModelRacecraft10 күн бұрын
👍
@716_sam111 күн бұрын
Joe, i have a N/A 5.3 LS swap in my c10. I have a cam and thats it. What injectors should i run? Im having problems with my terminator x going into closed loop and learn mode. I have a feeling these stock injectors are my problem
@todds595611 күн бұрын
Do you offer remote terminator x tuning?
@lukesimeon575612 күн бұрын
Very good
@leeboyzx6r12 күн бұрын
How much would you charge to send a copy of that tune to me?
@leeboyzx6r12 күн бұрын
I'm having a hard time finding somebody who can tune an exact setup
@87corvair12 күн бұрын
Hey I'm hoping you will help me but I just put a sniper 2 on a elcamino and the quick start guide for getting it initially programmed is a pos. Didn't work, now there is no wizard. I didn't erase anything or turn the key off until I was good and pissed off. So please hopefully you can help.
@716_sam114 күн бұрын
Joe, is their a separate CAN connect for the pro dash or is there only one? I need to run the wizard again because i going to get new injectors, i dont want to have to undo all my work when i end up getting them so i want to leave the handheld connected as well as the pro dash. Should i be looking at getting that CAN splitter cable? Thanks
@jonpeterson153816 күн бұрын
Did you wire vehicle speed (VSS) in to your ECU? If so, how? I've a Boxster S with an LS3 running and OEM ECU and need to get VSS wired in to help with some driveability smoothness but am having a hard time finding documentation on how people do it.
@dirtbike66216 күн бұрын
The real question is who has the coolest sticker/ logo
@andretorben999517 күн бұрын
I bought and paid for a Holley Terminator and dash. After waiting 9 months for Holley to supply the items I gave up waiting and my performance store gave me a full refund. I bought a Megasquirt and dash instead. I really like the Holley products but what the hell is going on with supply ???? I dont regret getting the Megasquirt. It works great and has great support.
@JoeSimpsonAtTempest17 күн бұрын
@@andretorben9995 you just bought from the wrong place it sounds like. All that stuff is available
@andretorben999514 күн бұрын
@@JoeSimpsonAtTempest I thought the store was having me on so I called Holley and they told me the same thing. I dont know whats going on.
@ssswdon17 күн бұрын
Hey I have to say I love your videos pretty much in depth as I'm pretty new to this and I'm running a stock ECU but I do have a boost controller. My question to you is is it better to control power by boost or by timing? Sometimes you don't have to option to use timing if you're on stock. ECU unless your tuner happens to be with you
@Boosted37019 күн бұрын
Anybody else notice the numbers from the rows vs graph don't match up?? AE vs MAP shows 250+ going up to zero in the row above but 2, 4, 6, 8 in the graph below
@richardnevarez689919 күн бұрын
Joe, love the channel. What are your thoughts on SEP? Specifically, GB SEP / Bosch 34mm 1000cc/min, 96lb/hr@43PSI Injectors?? I am using the Terminator X on my Gen 4, 6.0 LS swap.
@mhardy21619 күн бұрын
Great content Joe! Out here doing the lords work
@Junderwood60621 күн бұрын
You got any videos on running a Mac valve without a dome sensor?
@JoeSimpsonAtTempest21 күн бұрын
In my training i do. I don’t remember if i do on YT or not
@Junderwood60621 күн бұрын
@@JoeSimpsonAtTempest thanks for the response was just looking into the training
@chaasayadsawapah22 күн бұрын
I went through this with FICs. e85 destroyed them over and over.
@mqk3hw22 күн бұрын
Who would tune for 16.0 AFR at WOT!!!! I have only a few dozen hours with hptuners with beaters and even I know that's absurd
@dekebell330722 күн бұрын
Can the Dominator, with or without additional other components, be used to control the IRS from a 2018 Camaro (graphed into a high-end C-10 build) for a track/show build? We've used the IRS's LSD with a crude control system (switches and a rheostat) for track use, but would prefer to have it integrated if possible. Thanks!
@dekebell330722 күн бұрын
I have so much to learn! Thanks for content, and for offering courses!
@Crodgers8824 күн бұрын
I feel attacked 🤣
@ColdBlue-6924 күн бұрын
I have a sniper XFlow on my 69 Nova. Do I download the Terminator X software to my laptop ?
@raulfernandez703525 күн бұрын
Deka 80 best budget option
@user-me8hc3bs7i25 күн бұрын
I'm in no way saying their QC guarantees anyone else having the same experience I have, but I've done the entire power tour and put another 3000 miles on my snake eater 100 lb injectors. I even ordered their extra cheap super china ones before they started offering the "same factory as bosch german sourced" injectors. I quit making any major tune changes 6 months ago and mainly have just been racking miles and I check in every now and then on the tune to make sure it's not going nuts. I ordered them being cheap thinking I'd blow up the bottom end learning to tune a turbo car for the first time anyways. If they fail however, I've got enough time and money dumped into the build that I'll end up going with nice name brand ones next time.
@runpuppyfpv574425 күн бұрын
That is not much hp honestly ! A naturally aspirated 383 will make almost or as much with no turbo
@JoeSimpsonAtTempest25 күн бұрын
Who the hell wants a naturally aspirated combo. Turn the boost controller a few times and this will make 800.
@350gtboi26 күн бұрын
ID and FIC are my only Options I sell!
@littlelifters754326 күн бұрын
I had sep injectors, one stuck open, one would intermittently cut out which melted a piston, replaced with a set of some odd 3/4 length bosch units, been running perfectly ever since.
@BoostedJo326 күн бұрын
Hey where you located
@or-ian697326 күн бұрын
They sound like they need to familiarize themselves with Holley better. And my buddies nearly new snake eater 1000s had an injector stick wide open after a pull. Stranded us. Snake eater blamed him for swapping o rings on one injector. Which he didn’t do. Installed them right out of the box
@SloppyMechanics26 күн бұрын
"tricked" into taco bell"
@FelixSalinas-di7ks26 күн бұрын
Part number on the dip stick?
@ericmiller428526 күн бұрын
ID or FID injectors... I wont buy anything else anymore.
@stephenhans18926 күн бұрын
Alway love 9 when someone uses a self threading sheet metal screws for grounds. Not much metal fo metal contact inconsistent ground
@TheSlim93gt27 күн бұрын
Buckle up Joe.
@andrewvehrs971427 күн бұрын
"But my buddy decapped his OEM injectors with an angle grinder and his car runs fine." I laugh every time a customer says this lol
@kevinwest368927 күн бұрын
To be good at anything, You have to be obsessed. sence i have limited brain Function and im not a racer. I think my Attempting to learn to tune at a Level 40% of What jo can do. Would be like Going to medical school because I have a broken ankle. By the time I figure it out. It will have grown back together all Crooked.
@D3thM3tal27 күн бұрын
SEP1500's going strong on 4 years now. I know they aren't perfect but it's been running great and making smooth power.