Do the tyres get subjected to higher wear? I assume the brake pads will.

I still get good gas mileage, but gas has gone up to 5.01 a gallon here. Plus the weetawds in Salem just banned all gasoline car sales starting in 2030. Gas on the gulf coast is about 3 bucks a gallon. Canada has oil tho.

Thanks man i appreciate it. It was pretty organized, but theres still a few things i wish builders would do on cam... like break the chain and line the sprocket... but ty, this is the most detailed one i can find. I wish someone would make a clear step by step tutorial though.

Ty. Just bought 1. However im a dumbass & it don't fit in the bike i bought. Im an idiot. Looking for your other vids

how to set how much gass can go n the carb

Use a 16:1 at first on a new engine for the sake of the wear in period (it gives that extra lubrication for the new parts shaving off metal fragments during the first couple hours of operation.). I run 32:1 in mine after break-in period, it works perfectly 😁

You got to do something because this video is boring as f***please excuse my language

💻 =💥

Yoooo this is fire

Next video semi-auto vs ... ?

The king of KZfaq has returned

I just go 20-1 on break in rhen run 40-1 for life after that....have 3 different setups and none have failed me and are all years old at this point 💯

I have a fat wheel with disc brakes will the rear gear affect the disc brake 26"4.0 wheel

My crank hits the exhaust any tips

Always install chain guard it only takes once and then you wished you would have

Always use a filter on a gas line

Never you use WD-40 on plastic or rubber

Never grind on aluminum

Always go in a star pattern tightening down your sprocket no matter tight you think they are never never never never never go in a circle at any time

Drill a hole in your handlebar to secure throttle. They will slip

Never stick a screwdriver inside of a motor

How get color chrome I get them

What size bike frame did u use?will 17.5 inch frame work? Mountain bike

Nice info man just built my first build its good to have info

everyone talking about the special oil they used while i just use some car oil for mine 😂

Tel them what cc stand

Great video. Number one tip. Bike will fail not the kit. Mine's on its third bike.

what is the size of spark plug tool? 16-18mm or 18-21mm?

You didn't talk about any mounting tricks even though you did something less than standard. Maybe it's a good thing for a part 2. Mounting shenanegans.

Thanks for sharing our music!

I've ran used motor oil for 4,000 miles in my 66cc kit (Since new about 5 year ago) Around the 3,000 mile mark the spark plug gap started closing up. I found the wrist pin and wrist pin bearing were worn. I replaced the top end (with original cyclinder that I sanded by hand to break the glaze) and it's been fine since. I run a thicker mix, probably 32:1, but I'm not even scientific about it anymore. I'd bet I saved enough on oil to buy another 66cc kit. Never even fouled a spark plug.

You are absolutely right

YOU NEED A CHAIN GUARD!!!!! If you dont wanna make the stock one qoek gwt a different one. I knew someone who died because his chain snapped and cut his leg, he bled out before paramedics could get to him. Use a chain guard or dont do this at all your life is more important than this.

9;30 you dont want what? problem inside the top

your way too quiet at key points

Thanks a bunch for sharing your knowledge. You've helped me out a lot.

An easy way to keep the engine from turning over is a few feet of small rope in the cylinder through the spark plug hole. Remember to leave a little hanging out. Old mechanics trick

I wish I was a kid again !

Thanks for the video, my brother still insists on riding these cheap motors so here we are watching your video, i remember messing with them over a decade ago before i decided to go electric.

Where is your c clip at on your needle

Post more

Post more

Post more

Post more

Post more

Post more

Post more

Post more

POST MORE I NEED MORE OF THIS PLEASE POST MORE

I use 40:1 and it goses