Matt's Machine Channel

Пікірлер

@ronin2167 24 күн бұрын

No mesa controller card?

@bobvines00 26 күн бұрын

Matt, are you planning to post any more videos in this series? Edit: Subscribed! ;)

@mikebaee7731 Ай бұрын

Excellent video, very helpful for me. Thanks a lot.

@GabrielGunderson 2 ай бұрын

Love this. So well done. Thank you for taking the time to share with us.

@user-rz2gj8fd1u 6 ай бұрын

Hi Matt I have been watching your video First Steps with LinuxCNC. I am a complete novice but want to try build a unit. I have located the Biostar A68N-2100 motherboard but I know I will need a power board, hard drive and fans. Would it be possible just to let me know the model numbers you have used in the video. If I use this Motherboard can it be used going forward to build a more complicated CNC? Paul

@norriemckinley2850 6 ай бұрын

Excellent videos! Very clear and well explained. Please do more!

@perrypark8485 7 ай бұрын

Great content, thanks

@sto2779 7 ай бұрын

Is it possible to use Trinamic TMC5160 drivers with LinuxCNC? Thanks.

@ozantayar 8 ай бұрын

This was definitely not what I was searching for about LinuxCNC, but I appreciate that it's quite a nice introduction for beginners

@nwbstplyr 8 ай бұрын

what application are you using to draw up your schematics? looks like a fun app to use

@mattsmachinechannel 8 ай бұрын

Hi, the application I use for the interactive circuit schematics is: KTechLab apps.kde.org/en-gb/ktechlab/

@andypughtube 8 ай бұрын

The parport tester is included in the standard LinuxCNC install, in the config-picker look under "apps" in "sample configs" Another thing to check if using a DB25 cable is that not all "printer cables" are fully wired. Many have only enough cores inside to drive (some) printers.

@SinedWOLF 8 ай бұрын

7:00 - А я всё никак не мог понять как искать дом в плюс по Z)

@user-pm8je4fo7e 9 ай бұрын

Thanks! First man on youtube who put an actual name of this generic driver in his video on LCNC.

@xyzspec82 9 ай бұрын

This reminds me of my first DIY cnc build 😊 Also started with a 3018 Will subscribe to keep updated

@mattivirta 11 ай бұрын

very hard, not understand and how can make eletronic because not understand all this, how start linuxcnc safe whitout this hard elektronic.

@migueld6851 11 ай бұрын

Thank you for the video, I really liked it. There are others on the topic, but I think they are very specific or sometimes they don't say much. With this, I now know what materials I need to start testing LinuxCNC with something connected! Thanks!

@Dark_Phoinix 11 ай бұрын

Sorry for the question, linuxcnc work only with parallel port?

@migueld6851 11 ай бұрын

No, it also works with Ethernet cards like the Mesa ones, but they are expensive and rarely in stock. I'm quite new to this, but I've noticed that Mesa cards haven't been available in stock since 2021. If you're new, like I am, consider starting with testing and experimenting with serial communication."

@Dark_Phoinix 11 ай бұрын

@@migueld6851 Thank you very appreciate

@mattivirta 11 ай бұрын

i just build my cnc X axis, limitsSW both end, and home inductive sensor left side X, i configure 2 paraller port card, used, first main port has connected all home axis, XYZ, second paraller port have all limit SW. hard limit, not can go out of linear rails, have better connect all limitSW same pin 10 than E-stop or all limit SW own axis limitSW both side X, both limit Y, both limit SW Z etc. why my first test i call homing X, go to left my home SW, BUT why start go back to right side after connect to home SW, and not stop, need E-stop can stop not run out of rails. what need make ? home X,home Y, home Z, have configured. and all limit SW have top of rail, and configured 2 different style possiple use, all limit same pin than E-stop, or all limitSW pin X11,Y12,Z13. second paraller port card, because one paraller port have only 4 pin can use.10 E-stop, X home,Y home,Z home, and pin 15 probe. what need make configure wisard ??. home axis right ? my X have 0 to 800 ,linear rail dimension, Y 0 to 1000, Z 0 to -300, have this right ? home setting 0.0 search home 1,5 mm/s what need do. homing normal ,if bush button home X then move left to minus but stop then connect home SW.,why run back to right ? and not stop newer, if not bush E-stop run out of rails and broken machine. help please what need do go normal only left and stay stop to home position.if i bush button home X , Z and Y not have tested yet, not all parts have ready.

@mattivirta 11 ай бұрын

or need i buy 6 inductive sensor more(expensive option) and make soft limit too my machine ? i have mechanic hard limit SW 6 pcs, to installed and 3 inductive sensor home SW to X left side, Y front side, Z up side. X left is 0.0 to right 800, Y front 0.0 to back 1000mm, Z 0.0 up to down -300 . have this right at configuration ? i not know. 0.0 have home position.

@rastanator- Жыл бұрын

Literally what I satrted from 2 years ago.(Dragons Ahead!-I thought than :)..) I think it is sometimes better to mention why so much is not important and its only example for testing. Great video looking for more ant subscribed ;)

@raymondvillain Жыл бұрын

Will LinuxCNC run on Ubuntu?

@andypughtube 8 ай бұрын

Yes

@AdamMaszynotwor Жыл бұрын

Dobra robota !

@MrStarTraveler Жыл бұрын

That's what I needed to learn! Good stuff.

@alexparish937 Жыл бұрын

Have you published you pcb designs anywhere. I would like to download them & try them out. Thanks.

@mattivirta Жыл бұрын

second step, need make linuxcnc working easy double Y axis motor, not good now have basic setting worst not can add 2 Y axis motor, and if add not working newer only lot errors.

@noanyobiseniss7462 Жыл бұрын

Your not going to have an overheating issue with those drivers butting up to each other?

@mattsmachinechannel Жыл бұрын

Hey! You may be right - I've not noticed that yet but I'm not putting them under real load yet. It is getting quite cramped in that enclosure, though. One of the reasons I like having everything clip onto DIN rail is I can easily move things around later if I need to, I might end up with the drivers in a separate box eventually.