hello can i use PE foam as PCB foam with soldered keyboard?
@belphegor_dev Жыл бұрын
Don't.
@jayson5021 Жыл бұрын
Where can we download the software to customize lighting?
@prod4kay Жыл бұрын
with my eyes closed i can’t tell when you switched to the lubed sound test, don’t think i’m going to lube these
@megsman4749 Жыл бұрын
I vote PE Foam Mod. Very useful comparo.
@christophergalvez6975 Жыл бұрын
I don’t think it would damage the pc lol
@dr.hannibal8338 Жыл бұрын
how Durock V2 Stabs fit the alminum plate?
@dstrawsb3 ай бұрын
Did it last night, the left shift was so tight I banged it in with a tool.
@glatt1817 Жыл бұрын
This is what I ended up doing. Note, some C2 boards have an additional F-row screw. I had intended on adding neoprene to fill the case, but my sheet was a tad too thick, and I didn't want to press on the PCB. Too bad though, as it improved the sound immensely. Fyi, get something thinner than 3/32 in. My case came with two sizes of foam, but the thin one (seen in this video) worked best, and didn't press too hard into the plate with the tape mod included. That's what I settled on, and have have some peace of mind that I'm not causing any damage.
@froggore52 Жыл бұрын
I sure would have liked to see how the switches actually go in with that foam in the way.
@alfonso5026 Жыл бұрын
Sounds like PE foam completely changes the sound, cutting off the high frequencies every key press. While Poron keeps the sound profile, but makes it sound dampened and a bit muted
@infinitiki2 жыл бұрын
When listing to the diff in the stock and pads, I think the pads made the sound much cleaner and clearer
@ejlagunsad2 жыл бұрын
Is it ok to both do PE foam? Switch pad?
@vincetheveganprince Жыл бұрын
I don't see the point in that. Its just more effort and you're double layering it. Just choose switch pad or PE foam with tape mod AND foam in the bottom layer.
@nndaystar2 жыл бұрын
Great vid! Was trying to put a finger on (haha) what kind of sound my board fell under! Clacky all the way!
@LittleMew1332 жыл бұрын
I kinda like the sound of quieter clicky. I think it's kinda fun.
@dylan_streetlifting2 жыл бұрын
Are those the 62g springs or the 68g springs?
@boo79482 жыл бұрын
i triple layered these for ultimate thock lmfao, it works
@marcus-wv9ti Жыл бұрын
so you do both pe foam and pads?
@MiguelCommodore2 жыл бұрын
Underrated reviewer, 10/10 earned a new sub.
@shinjid37052 жыл бұрын
i didnt like the pe foam mod. Kinda makes typing louder than i really want. I guess switch pads is the best way to go to prevent hollowness and get a more quieter sound.
@vanessahuang66722 жыл бұрын
Same Its quite frustrating for those who prefer a creamy thock
@shinjid37052 жыл бұрын
@@vanessahuang6672 yeah i dont understand why ppl would want their keyboard to sound louder. It shouldnt sound muted but also shouldnt sound annoyingly loud.
@dlmiii12 жыл бұрын
B
@Bryan-eg7si2 жыл бұрын
Do you know which material to reccomend ? Eva , Poron, PE foam
@nimmy4042 жыл бұрын
The KTT mint linear should fit in here, using it on my anne pro 2 but I believe its outemu compatible, very nice cheap stock switches
@nye_z2 жыл бұрын
pinutol ko yung extra 2 plastic pins so it would fit onto my k530 draconic and it literally just worked no probs haha
@Kogami2 жыл бұрын
There are PE switch pads that could be a better alternative to PE foams instead of poron, have you tried those yet?
@nanto882 жыл бұрын
Haha pe foam mod better
@cristobalsoto52602 жыл бұрын
thanks you convence me to buy this keyboard instead of a tofu i appreciate it
@dinhphucnguyen262 жыл бұрын
how many layer of tape does the clacky one?:)
@hehehe96182 жыл бұрын
why didnt you apply both methods though?
@epikdude2432 жыл бұрын
i hate clicky but the clicky one sounds pretty good
@epikdude2432 жыл бұрын
but the thocky one is the best one hands down
@leafy_cs2 жыл бұрын
I think it isnt thocky, its like clacky with hollow.
@bignog36502 жыл бұрын
How did you get rid of the indicator light cutouts on the top case/frame? And did u use tape to cover the blue light indicators?
@XxCrazyManoxX2 жыл бұрын
I think he just repainted the case and maybe blcoked the light with a piece of tape underneath
@theguyfromcs22 жыл бұрын
is NOBODY going to talk about how clean the clicky one sounds
@hanzo43012 жыл бұрын
it sound really good tho
@entityerror86012 жыл бұрын
It’s click but not annoying
@Faath22 жыл бұрын
@@entityerror8601 blues are just doo doo
@GearObsession2 жыл бұрын
Not very noticable. Additionally; that foam will deteriorate into a sticky goo over time. Away; I still enjoyed the video, thank you for taking the time to post and share.
@jonathanelkin38302 жыл бұрын
can you use these switch pads with the foam in between the pcb and plate
@HeyNavi2 жыл бұрын
Late response, but I had the same question but I think the answer is yes. I just saw another video where they used the kbd switch pads and and then placed the pcb foam. However I also have switch tripods which I hope would work with all three combined. If it’s too thick then I’ll just remove the switch tripods as they didn’t make a big difference at all.
@nigolski2 жыл бұрын
yep
@bobi63742 жыл бұрын
I love the intro
@yellowcam14222 жыл бұрын
the clacky one sounds very nice
@haz20222 жыл бұрын
Nice video, You should have done both of them together but personally I do not think it is worth it
@zack_szh67692 жыл бұрын
the solution to every keyboad problem is to get a Model M
@Dyto692 жыл бұрын
You know it
@V4V62 жыл бұрын
but tbh tofu looks better than blade (IMO)
@robertochannel3847 Жыл бұрын
well the blade 60 tray mount is a lot better than tofus
@V4V62 жыл бұрын
lmaooo trueee
@niko1even2 жыл бұрын
The chances that the PE foam mod will damage your PC is extremely small to none. PCs have many safeguards in place for that sort of stuff.
@mackskbd2 жыл бұрын
i used to agree, but after changing some switches out a couple of times, 4 sockets on 2 pcbs stopped working. i think its a case by case thing
@niko1even2 жыл бұрын
That’s a socket problem. The PE foam mod if it were to do damage, it would be much more noticeable. Hot swap sockets loosening and/or breaking from the solder join is a common issue. It can be easily fixed with a soldering iron and new hot swap sockets for literally a few cents.
@dhaerque2 жыл бұрын
There is a certain type of pe foam you want to avoid, i forgot the name but if you look it up it’ll pop up
@nomad76282 жыл бұрын
@@dhaerque can u list those names?
@fux2372 жыл бұрын
is the PE foam you used in this video also 0.5mm thick?
@yudhaadiwijaya73102 жыл бұрын
nice comparison, do you have any recommended cheap switch that could do 3 of them decently?
@ilikesongs12452 жыл бұрын
Yellow switches
@ilikesongs12452 жыл бұрын
You can turn them into 3 of them
@ilikesongs12452 жыл бұрын
My most recommended is build a high pitch thocc its like a thacc
@yudhaadiwijaya73102 жыл бұрын
@@ilikesongs1245 too bad I only have outemu socket keeb that isn't compatible with the gateron yellow :( , what about Akko matcha green?
@ilikesongs12452 жыл бұрын
@@yudhaadiwijaya7310 akko hmm its not too bad
@colinhendry61162 жыл бұрын
"beautiful" Jack Hanma
@cyrellebesana18182 жыл бұрын
Does this model have bluetooth capabilities? I kept looking around but can't find more info.
@paklekj44292 жыл бұрын
No
@cyrellebesana18182 жыл бұрын
@@paklekj4429 yup. I figured eventually. Thanks.
@paklekj44292 жыл бұрын
@@cyrellebesana1818 if u want wireless version buy c61
@cyrellebesana18182 жыл бұрын
@@paklekj4429 maybe next time. I already bought x61 but i sold it and settled for royal kludge rk61 because of the bluetooth connectivity. Thanks for the info!
@paklekj44292 жыл бұрын
@@cyrellebesana1818 wait you use bluetooth? Whyyyyyyy it has dongle bruh dongle node is more responsive and less delay comoared to bkuetooth
@oniichanyamete39922 жыл бұрын
Do a comparison with rk61
@paklekj44292 жыл бұрын
Not wireless Outemu socket White led only Bad packaging obviously
@1700tt2 жыл бұрын
Have you tried using polyfill?
@BeefiusGravius2 жыл бұрын
I wonder if the Polycarbonate plate + Foam would add some flex, even if its just a little more than the Brass/Alu option. Nice Video, interested in getting this board for myself, nice to see a case that isnt just two boxes stacked on each other or just a rectangular slab.
@ripfrickingben2 жыл бұрын
proof this hobby is going nowhere.. hopefully my kids will see the light of quick gmk lead times and nicer budget cases
@baumbaumastast38232 жыл бұрын
Nice profilepic
@JP3Gl2 жыл бұрын
@@baumbaumastast3823 there is a light. the ikki68 has a round 2 and it looks promising. all thought the ship time makes me wanna cry it’ll be worth it soon
@zulk9mahmood8212 жыл бұрын
the blade is actually a very sweet keeb. it has tons of flex and sounds pretty decent to boot and doesn't break the bank