I used the Sylvania headlight kit about 2 years ago and my headlight are fine. About and hour and some elbow grease ... and the last step is a sealer so they don't just look like crap again a few months later.

I did same repair in my boat , it held up 2 years. I’m currently removing old to replace with new JB. It beats buying a new motor

Baby soap is fine, it's gentle, good lubrication and ph neutral. Most of the dirt with come off with propper prewash/snowfoam

This is 7 min's I can never get back! 👎🏽

JB Wells a good product I’ve used it quite a bit but it will not work on exhaust manifold. Too hot burns out.

Drilled a screwed to the engine,,does it work,NO,if its applied anywhere were there's no oil pressure,,ok product

with my mower the reason it has a small crack my engine mount vibrated loose, maybe check your they do vibrate alot

That makes me confident...i'll try it on my 18 hp lawnmower engine...finding a new engine absolutely sucks since it seems that there not many of them out there in the www...its funny ...every fucking may either my car lets me down or something else that i need every day..my stuff hates me

Back in 1986 my dad let his tractor freeze up. an old a/c it cracked the block on the side about four inches long I cleaned it up real good an ground a little right in the crack.i cut a little line at each end of the crack an filled it in with jb weld it never leaked again an he drove it another 20 years still holding when he sold it in the auction. Trust me I'm a believer just take the time to do a good job on the prep work an it will hold it's amazing.

I knew a guy with a really old car that never had paint that ever faded or chipped. The owner said he only hand washed it with baby shampoo for twenty years.

Yes I use it on my old BMW E39. Drivers side was awful but the WD41 improves it about 98% worth a go but probably once a week

Very informative thanks I’ll subscribe

milky oil before and after repair?

Yyyess this is what I was looking for

Here’s some tricks for using a Preval: 1) spray alcohol through it to clear the mechanism before putting any paint in. 2) make sure your paint is thinned to a skim milk consistency. 3) strain the paint well before adding. 4) be patient, spraying with several very thin coats, keeping the sprayer moving and not too close, to avoid drips. 5) if it spatters, do not use, switch to another Preval. I hope that helps, I use Prevals all the time for different types of applications. I’ve never tried it for an automotive repair.

What's the beat wet sandpaper to cut polish dust on ceramic clear

Thanks Donnie! great video, I'm getting it right now to put it on a small engine crack on my Goldwing.🤞🏾Take care!!!

Nope I did the same thing and JB weld didn't work.

i like the metal in the backround

Nice video covering some of the basics! Thank you brother for sharing your knowledge. I'm not a auto body guy but I did just pick up some spoons and a couple dollies. So I needed some advice on how to make things better not worse lol as I put my Tacoma into the wall a while back and it left some dents in the bed of the truck. Keep up the good work!

How can I purchase it from where

was water actually leaking out of this crack?

It does work. I had the same thing happen to me. Smaller crack maybe 4 to 5 inch long. JB weld worked pretty good and it salvaged my season.

I have an antique raised letter sign from Chicago pneumatic

I got more panties for your thoughts I mean tips thank you I truthfully did not know that

This stuff is AWESOME!!! Just dont trust the QUICK drying version. Isn't worth a damn. I've used JB weld on LOTS of stuff. Including... gluing a radiator back together on an Acura Integra that overheated and busted. The JB weld held so great.... the car overheated again weeks later.... but the radiator busted in a totally DIFFERENT spot. The JB weld held while radiator overheated with extreme pressure that time!!! Crazy stuff for sure!!!!

SELL IT

Just so you know, to google and deaf people...you're known as "Dying Smithma".

Hi, from Argentina, I have a Mercury 135Hp 2-stroke with a crack in the block.I want to try fix it with this product. You made it un 2013, how is now de engine?.-

Its all in the prep. Clean clean clean! I used it on magnesium motorcycle cases after I threw a chain. It lasted 10 yrs on a motocross bike ridden hard.

It says wipe off the excess u wiping it completely off. Also leave for 5mins before wiping

I fixed mine drilled out both ends of crack worked for years sold. BOat still running great

I repaired a Cummins ISM cracked block with JBW behind the engine starter on driver side That was 4 years 215k miles ago and the engine still running strong without leaks. Awesome product. I strongly recommend it.

Example of John Deere approved repair process with Belzona 1111: kzfaq.info/get/bejne/r5Nxh5uXnrCYj3k.html

Example of John Deere approved repair process with Belzona 1111: kzfaq.info/get/bejne/r5Nxh5uXnrCYj3k.html

Thanks for this valuable information! Got a small spot on my car, that I was going to use touch up paint on, but I figure I might as well go ahead and do it right.

Didn't like the Prevail paint system and got the You Can this week didn't like it either don't want to keep using reusable aerosol spray cans nomore better off with a paint gun or a aerosol spray can that not refillable.

Anyone have an update on how long this held? Looks like after our killer winter in Texas I’m gonna be trying this.

About how much would this cost?

Hi Donnie my brother and I just fixed our truck motor with jbw we hope it's going to be all good thanks

Did it last more than just 3 times out ?

I've a tiny oil leak which I think I've found where AC compressor is bolted to crankcase . Just changed my oil and filter . I'll make sure before trying anything . Tiny since I think it goes down very slowly just annoying . Yeah I hit something very hard . Possibly a problem if it still leaking when I try using permex / JB weld grey or black glue since it's supposed to be clean and dry ? Any helpful experiences out there ? Do I have to wait till I drain it during my next oil change ?

Uso imán neodimio magnético de microondas la puerta ya abierta esta

it stil leaks, i see the water drops in the video, is that taken after testride or? or when u discovered that new leak?

I think the technique and process he showed are spot on. I do think addition red paint in the area was needed and that is likely because the reducer/blender may have thinned out the color a little too much. But great video otherwise on a subject nobody tries to tackle. Most painters are like paint the whole thing blah blah blah because their afraid. Trial and error is how people learn

My 350 sbc block cracked below exhaust about to fix mine the new k&w lime green bottle to run through coolant works great but I'm not big on mixtures in my motor good luck

JB Weld is a brand. You need to state what exact product you used.

Just what I was looking for. Thanks

If you have mouth sores another solution to try is acidophilus. It is a good bacteria that is naturally found in your mouth and your gut, it comes in pill form or liquid. Put this on the mouth sore and within 24 hours you will see an improvement. My son had mouth sores and the doctor burnt off the first one, I swore I would never put a child through that again so I went to the health food store and was able to get this and it worked fantastic.

good enough. f it.