Quick question. They indicate the output level of control at maximum. Does the input gain level set at maximum too? They don't say
@alexismethenitis4 күн бұрын
They do say: Input is to be set as to get a 0dBm (0.775V) output
@sanolivo68674 күн бұрын
thanks much
@SCanOz8 күн бұрын
Hi, I want to replace and upgrade everything on my Sony ta-f435r. It doesn't work anymore. Where can I order the parts?
@alexismethenitis8 күн бұрын
Hi, DigiKey, Mouser and many oher places.
@sanolivo686715 күн бұрын
Where did you get that Service manual. It looks nice and clean. Everything I have downloaded is dark and foggy.
@alexismethenitis14 күн бұрын
I made it my self.
@sanolivo686714 күн бұрын
@@alexismethenitis ohh wow looks really good
@dannyyy101224 күн бұрын
Saw one at a local thrift store today, dirty and with user marks for €15,00 Hesitated because of its state and lack of the right tools (long screw drivers) for restoring it.What type of screw driver did you need? Maybe if it's still there I'll pick it up.
@alexismethenitis21 күн бұрын
Hi, I belive you should. You will require a philps screwdriver at least 30cm long.
@stefanindjov9892Ай бұрын
Best Regards from Sofia, Bulgaria. I have the same.
@muhannadrh41Ай бұрын
Hello (I am from Iraq). A wonderful and useful video. The most beautiful of all is your humility and your responses to all questions. I wish you peace and success.
@alexismethenitisАй бұрын
Hi Muhamad, thank you for visiting and your kind words. All the best.
@robertomoran3627Ай бұрын
Este equipo tiene el STK 465 gran integrado, Tengo un Sanyo DCA303 y lo hago trabajar con bocinas de 350 watt, de 15 pulg vaya mejor que una potencia y con sonido nítido, será que puedo hacerlo trabajar este amplificador con esas bocinas, claro le he puesto 4 ventiladores de computadoras para que enfrié el integrado, de esta forma lo he echo trabajar mas de 12 horas y como si nada. inclusive alguna vez le conectamos guitarras eléctricas, órgano, micrófonos de una banda atravez de un mezclador y nunca se daño. Sanyo hizo un gran trabajo con ese equipo, estoy buscando uno del mismo donde me encuentro pero no encuentro.
@simonzinc-trumpetharris8522 ай бұрын
These amps can get HOT!
@dietriho2 ай бұрын
Can you tell me which test band with which reference band flow (nWb/m) you use for the GX 636 to achieve the 0.775 V (0dB) at the output?
@alexismethenitis2 ай бұрын
Akai test tape 250nWb/m standard.
@anikbrenzik86952 ай бұрын
Why don't You adjust the bias setting?
@rvd889562 ай бұрын
Many thanks for creating this video, super helpful! Going to do this soon as well on my c320bee. What caps did you use for the main filters at the power supply? (The big black ones rating at 15,000uf)
@alexismethenitis2 ай бұрын
Hi, thanks for visiting the channel. I didn't replace the main filter caps as they were fine.
@zipnemesis2 ай бұрын
Thank you so much i have 2 reel to reel deck from 80's Akai rx625 and rx646 both have same problem they are slow and stops during rewind and fast forwarding and they both have same dual motor run capacitors and i don't know which capacitors to use as replacement I can’t use this deck for years any help deeply appreciated thank you in advance.
@alexismethenitis2 ай бұрын
Hi, from the schimatic, both reel motors have a 4+4uF/250V cap. You can't find caps like that any more. You have to buy two 4uF/250V film caps and wire them accordingly.
@zipnemesis2 ай бұрын
@@alexismethenitis Thank you very much
@springguntunes2 ай бұрын
On mine, it looks like NAD raised the zeners and resistors high off the pc board. No overheating was observed.
@alexismethenitis2 ай бұрын
Hi thanks for watching. The good thing about NAD is that they update when they find a "bug". Enjoy!
@zipnemesis2 ай бұрын
Excellent thank you
@alexismethenitis2 ай бұрын
Thank you!
@kluck9993 ай бұрын
The main problem is usually engines and mechanisms, not electronics).
@quebecforce1113 ай бұрын
the sound of this amp are good? not alots on review on the web
@dennycastellanos36273 ай бұрын
Hi Alexis Thanks for all your help
@sanolivo68673 ай бұрын
I like your style. You do good work
@alexismethenitis3 ай бұрын
Thank you very much!
@carpenterole4 ай бұрын
hallow my akai ther are no sound (out ) on rigt kanal ?
@alexismethenitis3 ай бұрын
Hello, 1 million reasons!
@ptvav4 ай бұрын
Hello. Please tell me, today do you still consider the NAD 302 a good amplifier or should you look towards the 352, 356? I have a Dynaudio Emit M20 and they need an amplifier with some punch and many people say that NAD is suitable for inexpensive ones. There is no money for KRELL or HEGEL(((. Thank you
@alexismethenitis4 ай бұрын
Hi, I do not believe the 302 will have any trouble driving those speakers. If you want you can try the 304 with more "horse power"!
@johanburger44544 ай бұрын
What device would you recommend using with this amplifier. I'm looking for something that has a USB port that reads flac. Ila novice, please help. Love the Nad, I have had it for 30yrs
@alexismethenitis4 ай бұрын
Only devices that have a line out (either RCA to RCA or mini jack to RCA) can be connected to this amp. This amp is pure analog, no digital inputs. You can connect any digital device that plays flac (PC, MAC, digital walkman) either through Line out if they have it or through a usb interface. I use a HiFi Walker with a mini jack to RCA cable to any input on the amp.
@johanburger44544 ай бұрын
@@alexismethenitis does the walker play flac mate?
@alexismethenitis4 ай бұрын
@@johanburger4454 Of cource up to 192KHz/24Bit
@polyglosystic.4 ай бұрын
I own two of these amplifiers, a C316BEE and a C356BEE. I had the same heating problem with the C356BEE, I replaced both the zener diodes with 5W zeners, and the resistors (3.3 ohm/2W and the 51 ohm/5W). Regarding the cooling solution I simply bought the "AC Infinity AIRCOM S7" and placed it on top of the unit; it is a more elegant solution to this problem.
@alexismethenitis4 ай бұрын
What ever suits your needs.
@smbanandanand45664 ай бұрын
Which desoldering (make and model) are you using please ?
@alexismethenitis4 ай бұрын
ZD-915
@csab1hd14 ай бұрын
Ihave two of 590s, with two different main pcb... one is similar like this but the other is a basically different version... i dont know what happened, older or why ...
@alexismethenitis4 ай бұрын
Hi sorry I have no idea about that.
@EpicBerlin494 ай бұрын
Thank you very much for these wonderful videos. They are very helpful. I would like to replace all electrolytic capacitors on my 770ES. Just like yours in the video. Would it be possible to get a list from you so I know exactly which ones I need? Best regards from Germany
@alexismethenitis4 ай бұрын
Hi, thank you for visiting. All the caps are on the service manual. Very easy to catalog and order.
@EpicBerlin494 ай бұрын
@@alexismethenitis I sat down yesterday. And picked them all out. You took the ATET 1000uF 63V from Würth, unfortunately I can't find it anywhere. Are you sure you have installed the ATET series?
@alexismethenitis4 ай бұрын
@@EpicBerlin49 If you can't find it, the ATLI or ATG5 is ok. Or any other brand if you like. I use Wurth for power caps for their quality.
@EpicBerlin494 ай бұрын
@@alexismethenitis Ok, thank you, it helped me a lot. While recapping I noticed that my bias current adjusment coil T401 was broken. Maybe you have one left over from an old deck? Or do you know where I can get a replacement?
@alexismethenitis4 ай бұрын
@@EpicBerlin49 No worries. Sorry I don't have any. I really don't know if you can find anything within specs.
@marcelvanooststroom17335 ай бұрын
Nice job Alexis. Finaly somebody has done an electrical adjustment on a Sony ES deck. I’ve done mine (TC-K750ES). A few points I want to highlight: Is your multimeter capable of reading the right AC voltages at 19kHz? (MPX-Filter check). As far as I know the UNI-T meter goes up to 10kHz when measure AC voltage. A multimeter drops down the reading at higher frequencies. Maybe an oscilloscope would help if you have one. For the Erase Current Adjustment you need to adjust RV553 at 110mV at 160kHz. I know for sure my Fluke MM can’t handle that frequency when measure AC voltage. Therefore I use an oscilloscope (no software scope). Probably you can’t read a voltage on your meter because of the higher frequency 😉 Do you use the resistors as mentioned in the service manual or do you connect your cassette deck directly to a function generator and/or meters? My regards.
@bertuchi19905 ай бұрын
ABSOLUTAMENTE FANTASTICO.
@user-tv3nu8zs3s5 ай бұрын
Good audio machine.
@carloferrari36715 ай бұрын
Hi Alexis, first of all I'd like to thank you very much for the great video and the terribly useful list of capacitors. May I also ask you if you do still have track of the varaible resistors that you did change (their value and type/size)? Should you still have a link at the Mouser/Digikey/whatever components, that would also be great. 😄😄
@1968shura5 ай бұрын
Параша на детских моторчиках😮
@user-Specialized.5 ай бұрын
❤
@quangphuongbangcoiquangphu73306 ай бұрын
❤❤
@gheorghefrangulea66866 ай бұрын
i think it had a service beacause c458 and c945 are original transistors i see that 2sc1845 wich is better than c945
@motortheo16 ай бұрын
Καλησπερα και συγχαρητηρια για τα βιντεο, απ τα καλυτερα στο ειδος τους. Εχω κ εγω 1 NAD 3020e, πριν και μετα απο recapp σε ηλεκτρονικο, συνεχίζει να εχει στο startup κ για 1 ,2 δευτερολεπτα 1V DC στην εξοδο του αριστερου καναλιου κ μετα πεφτει σε λογικα επιπεδα (10 20 mV ). Επειδή ο ηλεκτρονικός ¨σήκωσε" τα χέρια είπα να κανω εδω μια ερωτηση μπας και παρω καποια ιδεά που να ψαξω μετά.. ευχαριστω
@ketchup27096 ай бұрын
Hi Alexis, fantastic restoration, it's Manoj from India, i have the Same GX4000DB, I need a capstan Sleeve and a Belt if you can help me to get it. Thanks
@MothershipOracle6 ай бұрын
placed an offer for a 304 on e-bay, after reading a very positive review. i already have a more modern c 326BEE N.A.D, no phono stage, so needed phono inputs for records, as i was looking for a detailed sound, and the N.A.D's have such a great reputation for great sound overall, despite the grey (used to be brown) corporate, business type looks! LOL!! thanks for this demo.
@alexismethenitis6 ай бұрын
Thanks for visiting!
@hifirulezzz6 ай бұрын
This deck requires to desolder and clean both reverse switches - otherwise, it would not work reliably.
@alexismethenitis6 ай бұрын
Hi thanks for visiting. You are correct, I thought the camera was recording at the time but it wasn't.
@ClassicTrialsChannel6 ай бұрын
Still have mine. i bought it in 1994 from a secondhand store. The led screen didnt work correctly, from water damage. the signal was bleeding over from the next bank of leds. which is why i got it cheap. but it was an easy 5 min fix. the top solder joints were corroded together . i cleaned them up and made sure not cross connections and its still working after all these years.
@uterpia7 ай бұрын
Thank you
@alexismethenitis7 ай бұрын
No worries!!
@PanasonicCobra7 ай бұрын
Good job👍👍👍
@biggstile7 ай бұрын
My auto return won't function. If I take the plater off, I notice the long triangular shaped arm will trigger it to auto return, if I pull it gently. Do you know which piece to adjust inside to trigger auto return? What's it called l, or can you describe it/process to adjust it on the PL-50?
@ninhnguyeninh19727 ай бұрын
Hi Alexis Can you please tell me where you bought the part number to restore this machine Thank you and wish you good health always
@alexismethenitis7 ай бұрын
Hi, thank you, I get all my components from www.digikey.com
@user-gm1wv1wg6cАй бұрын
Вы талантливый мастер. Спасибо, очень полезно!
@carloferrari36717 ай бұрын
Hi Alexis, nice work! May I ask you where did you get the two pinch rollers? Their performace are very critical in that Sony serie and I have not reputable sources for them.. Many thanks!
@alexismethenitis7 ай бұрын
Hi, thanks for visiting. I got them from: www.hifiretroparts.com/
@alexismethenitis7 ай бұрын
@@uffepipoli3968 Best wishes for the new year to you too.
@rcary7 ай бұрын
I have a tascam 122 mkii. One of my levels is lower than the other on the VU meter. How would i know if its a low level signal or if the VU meter needs to be trimmed? Would i adjust the record level or playback level pot on the motherboard ? Its a bit confusing, I do have a good test tone calibration cassette if that helps?
@alexismethenitis7 ай бұрын
You have to check your service manual. If you input a known strength signal and both VU meters show the same then it is not the VUs.
@user-sq4lz7cc6p7 ай бұрын
Hi. I also have the same unit, it working however when side has most of the tape it start slowing down. What is your recommendation to solve this?
@alexismethenitis7 ай бұрын
Hi, do you mean during FF & RWD? If yes, check my other GX-77 video for solution.
@Bestforthebuck8 ай бұрын
Good job Alexis! So in conclusion, is it a decent deck or not, what is your personal opinion on it? Merry Xmas from Bulgaria😊 and Efharisto.
@alexismethenitis8 ай бұрын
Hello, thank you so much. Merry Christmas. For it's money it is an exceptional deck. If you can find one in good shape and price, buy it. You will enjoy it!
@szabolcskozsla8 ай бұрын
Never do that! (scratched the top) What a bum job! There are much better solutions for such powder problems (e.g. AC INFINITY).