Complete waste of time and effort... The Fan and surround can be removed with the bumper and Radiator is position... 1. Remove wiring for resistor and fan + - 12v supply 2. undo and remove two screws holding the fan in place, then slide the fan to the side to allow it to move out of the retaining tabs... 3. jack the front of the car up so the wheels are about 4 inches off the ground, then remove the fan and surround from underneath the car... Only one side of the car needs to be raised. Install new rad fan in reverse of removal. Time taken about 45 mins Max...
@sushi_garage2 ай бұрын
Maybe, but I was replacing radiator too and you can't remove it without removing a bumper. Radiator fan was just a "milestone".
@drouxbag943 ай бұрын
Got hardware for caliper off but still stuck and can't pull off caliper. It just wiggles help is appreciated
@sushi_garage3 ай бұрын
Maybe pins are still locked on threads and you need to push them out using screw driver, or you need to press the brake pads to compress pistons a little bit. Use screw driver too
@drouxbag943 ай бұрын
@@sushi_garage it was the brakes needing to be compressed thank you!
@Altul993 ай бұрын
Keep up the good work, l have galant 2.5 myself and could use some insight for workin on this car. : D
@Lizpolygigiblissgirl3 ай бұрын
Did yours have a woodruff key on the shaft or not? I never saw one on mine.
@sushi_garage3 ай бұрын
No, but I bought one and mounted. Just in case
@JRUSS803 ай бұрын
Clear precise straight to business…..thank you sir
@michelleb67374 ай бұрын
How much coolant did it take to refill the reservoir back up after being drained completely?
@royrichardson91644 ай бұрын
Where did you get the pads?
@sushi_garage4 ай бұрын
From authorised Audi dealer
@nicoledewinnaar49374 ай бұрын
If u need to put in stop radiator leak, do u out it in the resevoir tank as well?
@kolton88345 ай бұрын
Promo sm 🎶
@Tholo123lol5 ай бұрын
Love this series!!! I have a Galant sport myself that i am referbishing👍 its in a little bit worse condition than yours😅 looking forward to new videos!
@Jurgo45095 ай бұрын
Great restoration video, very enjoyable! :)
@Killian6655 ай бұрын
Stupid fake 4 piston calipers
@sushi_garage5 ай бұрын
Yes, but brakes in this Audi works quite good in my opinion...
@Spider55 ай бұрын
Masakra. Polski zakład a kanał yt udający zagraniczny.
@jacek_s5 ай бұрын
Litości! Przecież jeśli autor zamierza dedykować swoje materiały publiczności międzynarodowej, to robi to dobrze - kanał wówczas prowadzi się w języku angielskim. Nie udaje kanału zagranicznego!
@sushi_garage5 ай бұрын
Jednak więcej ludzi na świecie posługuje się językiem angielskim niż polskim, co nie znaczy że ukrywam pochodzenie
@henioo18775 ай бұрын
wiadomo polska gurom
@sushi_garage5 ай бұрын
Hi there :) Thanks for watching and please consider subscribing my channel!
@lasanadrammeh13086 ай бұрын
Good one
@allanmanning6 ай бұрын
Thanks. That's great help. 👍
@amerikanstafford7 ай бұрын
++++++++
@St3rmTig3r7 ай бұрын
Very helpful with all the small cleaning tips. Thank you for being so precise and detailed.
@mattm58678 ай бұрын
Great job, but you should always put teft tape on pipe fitting counterclockwise.
@asid7319 ай бұрын
Thank you for the video. What is the labor time on this?
@sushi_garage9 ай бұрын
I think it's about 2 hours of work with no hurry. It's also depends on rust on bolts and nuts
@asid7319 ай бұрын
@@sushi_garage thanks
@nacho15289 ай бұрын
Hello my friend. I have a question, what are the specs for the front brake disc on the SQ5. The diameter in mm and the size in mm, please.
@antonioalves54017 ай бұрын
380 56mm
@pteamg9 ай бұрын
Good job
@hid3nax9 ай бұрын
Everything is perfect except using AutoFren repair kit. It's crap which won't last long. There's nothing better on the market these days than TRW repair kits
@sushi_garage9 ай бұрын
Thank you. Unfortunately I do not have any TRW repair kits in my stores nearby :(
@hid3nax9 ай бұрын
@@sushi_garage There's always a possibility to order it online, in advance...
@mikecampbell742110 ай бұрын
You did not show the process for releasing the electronic parking brake ?? Maybe I missed it but normally I need an OBD 11 or VAG software for this part.
@sushi_garage10 ай бұрын
No need to do this. It's front discs and pads replacement video :)
@mikecampbell742110 ай бұрын
Of course Doh !! That will learn me for trying to be clever 🙂@@sushi_garage
@patryniapiotrek64311 ай бұрын
Nie odkręciłeś odpowietrznika! Pamiętaj o tym przy cofaniu tłoczków - ewentualny bród wypłynie a nie dostanie się do pompy ABS-u.
@VyasaSewberathMisser Жыл бұрын
Why aren’t you using a torque wrench to torque the bolts to the specified torque? Great video otherwise bro !!
@sushi_garage Жыл бұрын
Yea, I know I should tighten every bolt with a specific torque, but sometimes I can't find values in manuals. It's absolutely necessary to use torque wrench when you rebuild engines or other complicated things
@sushi_garage Жыл бұрын
If you like this video please hit that Like button and Subscribe my channel 🍣
@sushi_garage Жыл бұрын
Hope you like it :)
@TomSmith-kc8mz Жыл бұрын
$2,400 quote from the dealer for this. I almost drove off the road. 😂
@djtintin Жыл бұрын
where on earth do you get an imbus number 9?
@sushi_garage Жыл бұрын
If you can't buy imbus number 9, you can find and buy 3/8 inch. It's around 9,5 mm.
@tmtoplak222 Жыл бұрын
3/8 doesn't fit on mine.
@drouxbag943 ай бұрын
Size 9 hex bit at O'Reilly's
@leftshoe202 Жыл бұрын
You da man, boutta tackle this myself today. Hope it goes well!
@sushi_garage Жыл бұрын
Not a big deal. Good luck:)
@pierrebnh Жыл бұрын
Should hit the hat of the rotor to dislodge it, not the rotor itself.
@fuadkrasniqi3236 Жыл бұрын
You sir... Is a Hero. Thank you. Do you have a video on how to change rear shock absorbers on Audi SQ5 2013?
@couturesworld6134 Жыл бұрын
Where are you located ???
@maureencameron5234 Жыл бұрын
"promo sm" 😎
@Stefanos.Tsokaras Жыл бұрын
Nice work!
@chrisr4804 Жыл бұрын
that doesn't seem all that difficult. Great vid.
@Morzsaszar Жыл бұрын
Thank you!
@highwayman1769 Жыл бұрын
Really clear video - Thank You
@storsina762 Жыл бұрын
Any other way to remove radiator fan with out having to break it all down can you remove the skid plate and reach up under it loosen screws and drop it down thru the bottom just wondering
@sushi_garage Жыл бұрын
To remove blower only you could try to unscrew this two bolts first, disconnect this two plugs and you will see if you have enough space to take it out. But personally I think it will be impossible. There is no enough space but you can always try before removing front bumper. Good luck.
@sushi_garage Жыл бұрын
Hope you like it :)
@sushi_garage Жыл бұрын
Hope it'll help :)
@dannygameplayes63634 ай бұрын
It helped, ty from 🇮🇹(where this tuna can was invented