Where did you get the new tank from? My Citroen has the same problem Thanks
@robantrum7213Ай бұрын
How about cranking the engine whilst pulling?
@checker36942 ай бұрын
Probably a car dealers car, No fuel😂
@adamwilson872 ай бұрын
Where about are you bassed and what was the cost for replacing cooler and other parts.. thanks
@peteroutram93923 ай бұрын
Where are you based ? I would like to contact you directly if possible?
@CrniH3 ай бұрын
hi, thanks for the video. Just replaced my rear sensor, and am not getting 5v it reads 0V. Diagnostic scan shows 5v on the front one though..any ideas? Checked wires, look ok.
@emice89843 ай бұрын
Hi to everyone . Maybe someone know , does the additive pump work constantly or just when automatic regeneration is ON ? Thanks in advance about answer .
@goodbyetothepeople923 ай бұрын
Hi. Where is the glow plug control module located on a 2020 Audi Q5? Is it easy to swap out? Also what is the part number for the module?
@pmccutchoen58404 ай бұрын
To calibrate the level you must have the car on level surface and have no one in the car 😂
@rccarmontenegro25294 ай бұрын
great video. I have a mercedes c class w205 2015 year, c 250 diesel. I cleaned the adblue injector . he turned on the check engine light. p220162 The NOx sensor (cylinder bank 1) has a malfunction. The Signal Cimparmision is Faulty. when I clear the error it is gone for 20-30 days or 50-60 kilometers and then it appears again. how do I know which sensor it is, upper or lower, what should I do?
@jlubana36124 ай бұрын
Hi mate when you got the car in the workshop did any white smoke and water used to come from the exhaust and any leak near the catalytic converter?
@ceemer205 ай бұрын
Tłumaczenie wrong conclusions. Sensor no. 2 is activated only after the engine has warmed up and driven about 15 km on the road. Note that you have no readings because sensor 2 is not even powered by the ECU. Only after the NOx catalyst warm-up procedure, the ECU turns on the module power and starts the ppm measurement. The faults result from the Nox sensor being clogged with dirt.
@robinpengelly82025 ай бұрын
Nice work. How are you coding with Xentry? Are you working for a dealership?
@yasahibuzzamman2755 ай бұрын
Hi, how can we book an appointment with you ?
@TRONICSfer5 ай бұрын
Just had check engine light on my 2019 g32 520d. The BMW garage told me it's a nox sensor and they will need to do further examination (I gues similar you did). But the strange thig is that car has only 77 000 km and there was no ad blue error, just check engine light ... Is that normal on this mileage?
@jaykent66455 ай бұрын
Great video and thank you for sharing but.... the original fault appears to be the adblue injector leaking, after the exhaust was cleared of the blockage what was cause adblue injector? If yes there was no mention of rectifying the issue before handing back to the customer? Also what was the outcome with the differential pressure pid reading zero, did that change after the software update? Kind regards Jay
@Ron-iw4fj5 ай бұрын
How do l find you as l have similar issues with mine
@user-hh8tw1gf4n6 ай бұрын
Great job boss but that broken dpf is not making any trouble
@markobrien55516 ай бұрын
I’d say the adblue got deleted because it had a problem or intermittent problem and has a good chance that it will be back, hopefully no other p codes had also been deleted that might be showing their faces again, hopefully it previously only had a contaminated adblue injector that also blocked the DPF causing the remap but I think the EGR cooler will also be full of crystallised adblue, next time take the O2 Sensor out and get a camera out. Good video though. 👍
@jola8706 ай бұрын
A ford tech here, put tension on them and leave it for an hour or so , if you force em they will break or bend . Just take your time. If you snap one it won't be fun , belive me.
@IraKilla6 ай бұрын
I’m bought a toolset and gonna change my injectors this weekend, any advice?
@jola8706 ай бұрын
@@IraKilla start with penetraiting oil, I only had a few that was stuck. Most come out easily. Just take your time... God luck
@IraKilla5 ай бұрын
@@jola870 I was planning on doing so, I actually sprayed it today. I hope it fix my “service now” problem that comes up when hitting 2000rpm. Thanks for your reply
@jola8705 ай бұрын
@@IraKilla if the " service now" goes away after you let go of the gas pedal like 10 sec later then it's the injectors. You know they need to be programmed?
@IraKilla5 ай бұрын
@@jola870 yeah it goes away after like 5 seconds. I have diagzone pro it has the programming option there I’ve seen it but I’m afraid that the injector stuck on me so I’ve been just lubricating it and not having the balls to change them😂
@user-hg1jf7ic6w6 ай бұрын
Hallo, Welches Dichtmittel soll ich für den Zahnraddeckel und die Kurbelgehäuseschale verwenden ?
@Leon_Brown6 ай бұрын
I dont have those yellow clips inside the seat. The leather seams to be connected to little metal rings which are connected to a metal line that runs trough the foam.
@Doovde697 ай бұрын
What part number was it you needed to replace?
@Doovde695 ай бұрын
I ended up with a BMW specialist replacing mine and at the same time had to do a software update on the car as well to make the latest sensor work.
@Assasin374 ай бұрын
@@Doovde69which Car?
@Doovde694 ай бұрын
BMW F16 X6@@Assasin37
@scottgray60997 ай бұрын
I have a C3 Picasso with exactly this problem. I mean basically the Picasso and the van are twins, just with different interiors pretty much.
@Propolizei7 ай бұрын
Have same error on my Focus mk3 2011. Also I see a condensation in my front right head light, and upper led light in it doesn't turn on when engine starts (only in evening, when low lights turn automatically) Any advice? Thanks
@prashlovestech7 ай бұрын
Really useful and helpful video to understand how the Ad blue and NOX sensor works.
@SocksWithSandals8 ай бұрын
Yeah, I got stuck with the Launch - System selection menu was limited.
@xuantrungnguyen3198 ай бұрын
We need on- off 3 times when reset? Right sir?
@Jonodrew12868 ай бұрын
Even the pitchler tool can struggle as its primarily rated at 12 tons - they however do a 20T ram adaption - but how strong is that head really - its the new M9R nightmare 😂
@Shadowknightneo9 ай бұрын
Wait what year is this? I have a short to ground error and replaced the sensor still got it but looking at the video it seems the leveling sensor has 3 wires coming from it where mine only has 2, wondering if a wire has become detached somewhere and that's throwing the fault code!
@TheFuneralDirector9 ай бұрын
Always clear diagnostics .. hopefully your subscriber base will gain more momentum you deserve it ... Regards Andy
@vlmxs9 ай бұрын
I have run into the same fault codes (although "Static" no longer "Intermittent") on my 2018 C7 (3.0 TDI CZVA). I would like to check if this was not caused by water or moister damage. The bad part the new sensor is 700 EUR (NEW) with aftermarket brands selling around 300 EUR :///
@vlmxs9 ай бұрын
BTW did you just swap the sensor in the end? Which one did you go for - original or aftermarket?
@khalidh98939 ай бұрын
Do you know where I could purchase a replacement? Having similar issue. Thanks
@JustMe-Dude9 ай бұрын
i'm a bit confused. why did you buy a launch UK particulate filter cleaning gun, and not use the launch UK DPF cleaning fluid? currently, I can't get either launch or wepp in the usa, and I'm still looking for the exact product that matches the launch uk product. it appears to be a private label repackage from Germany.
@EverydayGarageYT9 ай бұрын
We have both the Launch and Wepp in stock in the workshop, we are just currently using the Wepp.
@sebastianokeefe40745 ай бұрын
hi can you give me some advice on my gla200 data from scanning, the live data values for p soot content high , many thanks seb
@EngineerLewis9 ай бұрын
Isn't there a way to clean these components using the same fluid that cleans DPFs? And what did the replacement parts cost?
@JustMe-Dude9 ай бұрын
when the soot is that heavy, it's a lot of work, and difficult to do. doing it on car, could cause damage to the engine, and even lock up the piston against the head.
@mickios1269 ай бұрын
Had an engine management light on. Booked into audi specialist. Turned out to be this .. just came home. All good so far. £100 labour £100 part . £40 tax 😢 £240 all together . . A lot cheaper if I knew what I was doing. Your vid helped see what they did. Cheers
@mrwells1234567899 ай бұрын
Another brilliant video great work keep them coming everyday garage
@mrwells1234567899 ай бұрын
Also keep up the good work I find your videos very realistic and informative
@mrwells1234567899 ай бұрын
I wonder if laser would warrant this as faulty if you haven’t exceeded the 250nm then in theory the tool has failed to do what it’s being asked of and sold as
@nigelbryant59329 ай бұрын
Mine failed last week. Far too complicated. I had a broken wire in the passenger side headlight. Absolute nightmare. Ford wanted £1200 for a headlight. I got mine fixed by an auto electrician for £100
@jessebudelman8 ай бұрын
Same issue I’ve had, pretty sure my connector isn’t connected tightly because I broke a clip notch on the headlight casing. The factory hid’s are pretty pricy, after my accident the repair shop couldn’t track down a new headlight and had to settle for a refurbished unit.
@styusuf567110 ай бұрын
Where are you based? have a similar issue with my preface lift ST3 and would like it resolved!
@EverydayGarageYT10 ай бұрын
We are located in Bedfordshire, we typically book 1-2 weeks ahead.
@styusuf567110 ай бұрын
@@EverydayGarageYT do you have contact details please?
@EverydayGarageYT10 ай бұрын
@@styusuf5671 01525383000 if you give this number a ring, we are open 8:00-17:30 on weekdays and 9:00-13:00 on a Saturday.
@EverydayGarageYT10 ай бұрын
Leighton Buzzard Lu7 4ff
@freddyfezz81716 ай бұрын
@@EverydayGarageYTHi, my st has the same issue. Could you give me a price for the replacement harness please? Cheers
@mrwells12345678910 ай бұрын
This is a great video keep them coming
@EverydayGarageYT10 ай бұрын
Thank you Mr Wells! Will do!
@leeroyjenkins908310 ай бұрын
This videos very useful thanks. I’m having a issue with my Ford focus st and the cars at Ford and they cannot find the issue. They have had the car 6 hours and no luck. I’m getting the c1a03 error.
@EverydayGarageYT10 ай бұрын
Glad you enjoyed the video, has the issue been resolved yet?