Hello! How much KV on motor?

Could we get the model files?

Actually, I did this, but the effect was not ideal. First, when two ESCs share one battery, the voltage drops very quickly, and it can only last for about ten seconds before it starts to slow down significantly. In addition, it brings a bigger splash, making the hull more flooded. But I still hope that you can give a more optimized solution, thank you!

where did you get fitting for the water to exit side of boat

Check your fingers with a microscope after handling carbon fiber!

Amazing!! 1 point of critique: the red stripe is not totally accurate.

One of my pet peeves, people believing that , that's all there is to it. Talking about people believing they can get good quality parts without bringing it into CAD to create a model with clean and smooth surfaces and clean and accurate features instead of using scanning software to fill holes and estimate voids in the scan.

Great piece of kit, The price though?!? AU $1,200 is rather steep but I know nothing about 3d Scanners. Can you get cheaper scanners to do the same job? Excellent video mate, Thankyou. Jimbo - Australia.

Should we buy a separate traxxas gear

Broo can u send me file..... 😢

I wonder what an MJet M35 integrated into Skippy would do. 😛 LOL

What’s the wheelbase of this little RC? I have a 1/12th 3D printed body but I am unsure how to match it to an R/C frame.

This is a way better method of making an outboard for RC. I see so many prop drive outboards for 3D printing but they are all complex, weak, and use lots of non-3D printed parts. I started printing a boat yesterday and ended up settling for a regular prop shaft. If only I had seen this :(

Pretty nice looking boat, dude! 😃 But you should 3d print a ninja Turtle to put in the driving seat!!! Stay safe there with your family! 🖖😊

the fact he didnt want to sell his designs first but becouse the skeeride became so popular he wanted a piece of the cake and released his files

No lie, I just realized I have been playing this video over and over just to hear the 2nd song (Sand Drizzles). Good stuff thanks you for doing this!

Hi friend. The tires you can made by 3D print tire mold and put silicone inside, some materiais to reforce, and some dust if you want this tire more hard

I read the a can of spray dry shampoo works too and cheap.

what engine did you use, how much hv. I installed 6s 1400kV and there was an air bubble in the propeller and the boat did not gain speed.

What is the runtime with this setup ?

Perfect mate! Subbed.

Very nice 🔵🔵🔵🙂🙂🙂👍👍👍🔵🔵🔵

Hey does your wing shift when moving the wing by hand?

Hi! I had the same problem with the servo arm/horn. Where did you get the plastic one? or did you just printed it?

You would need 3 scans, otherwhise a 60000€ scanner can also not merge it. In my opinion these Carbon Fiber Filaments are not the best to achieve maximum strength. To realy make a 3d print strong with CF you have to go for a Markforged Printer which can make the parts fiber enforced with real endless CF fibers. The strength of this Filaments with CF splinters is to make Lightweight parts but if you compare Nylon CF to Nylon plane. Nylon will outperform the CF splinter Nylon composite Part.

can this be printed entirely with PLA+? oh and also the FS Racing Differentials is absolutely hard to find, will an HSP differential or a ZD Racing 1/10 differential work?

Hey man, I know this is a video from 2yrs ago but will you also look into Jackmass's FENNEC RC buggy~ my unfortunate problem with this buggy is actually the metal differentials is pretty hard to come by (and is somehow overpriced on many stores in my country) the FENNEC uses a much more common HSP/Redcat Differentials (and is actually no options for a 3d printed one) You can also use the differentials from Red Cat's Volcano EPX Monster Truck (the 1/10 scale monster truck) and those RC Trucks were recently revived and reproduced so parts support for those RCs are still around

with❤ you can do anything

I have zero knowledge on 3D scanners, although I'm obviously here looking to get one in the future. Since you said the scanner has issues scanning black parts, why not spray the part with temp paint? Such as Plasti-dip (they have a ton of colors) , it dries and peels off when your done, assuming you do a good job painting, it will peel off very easily, of course little thru holes and what not may need a little extra "help". Just a thought, I could be completely wrong for who knows what reason, but I'm all ears. If anyone tries it, lmk if it works.

What 3d printer are you using?

Does this have a differential?

What size belt are you using

Is this having a locked differential?

It would really help if you would get actual measurements of servos' stall torque and speed rather than relying on manufacturer's specs which are often inflated. A simple test could also be devised to measure centering accuracy.

الحقيقه انك اسطوره

CF filaments can wear out your printer nozzle pretty fast. Make sure you have a hardened one.

Really great, Nice video 👍😊 I recommend you check out Jackmass' models, especially the Trophy truck and truggy, they are insane, personal experience 😄.

There is huge problem with this model bro it wont go reverse. I am using bidirectional 30A ESC.

Thank you. Excellent explanations for anyone and especially new people like me! Great idea and super useful. I hope it gets lots of views.

To help scan the other side use a geometry rich object like a printed maker tower or a couple crumpled up towel with the board up on its edge that way when you go around to the back side, the scanner can hold onto the additional geometry

can i ask waht kind of paint u used for green ? thanks , great job , im just finished printing

Hello I need a koenigsegg STL file please

As for filament, I've been looking into PP-CF for my printed RC part. Polypropylene Carbon Fiber. It's properties and specs, on paper, look phenomenal. I have some on its way an can't wait to put it to the test.

I know there's a lot of focus on the materials but what about this freak'n scanner?!?! I'm so impressed with how well it turned out! It doesn't seem like you had to do any "computer" clean up work. Like scaling or removing random artifacts that I've seen show up in other scanned parts before. Some will say it's expensive but if its really this good, and you have a business in this field, how could you not afford to be without one now?

For this particular part, I'd be tempted to print it on it's end so the opening of the joint-holes are facing the Z-plane, the side that has less of a slant is more ideal so it's less support material used. It would be best if the webbing/spine in the part had chamfering to drop those as overhangs. But the main idea is make the holes as structural as possible by being full loops, if you start getting any layer-splits consider trying that, else good layer adhesion!

What diff is that you use bud

You don't want 100% infill you want some give, I think 70% is the same strength as 100%, you want some give you don't want the parts to be too stiff they're just going to snap.

In combat robotics we use a lot of Polymaker polymax pla. Very strong and easy to print.

wow 3D scanners have come a long way, last time i tryde 3d scan something was with the kinect for xbox 360 🤣

Fantastic, dude! Thanks a bunch for all the testing! 😃 You can also try different infil geometries. Some are definitely stronger than others! Anyway, stay safe there with your family! 🖖😊