just ordered some boards from your file🙏🏽 thank u for those...how many pins do the type c sockets need to be? and video of your solder work
@qubitstech22 сағат бұрын
That's great to hear, glad the files could be of use :) The USB port is the 16 pin variant, something that looks like this www.aliexpress.com/item/33015630556.html
@funkyfoo71422 сағат бұрын
@@qubitstech thank you!!!
@funkyfoo71422 сағат бұрын
@@qubitstech was soldering the pins a pain?
@qubitstech22 сағат бұрын
I use solder paste for the pins, which I find fairly easy. I start with the pins to ensure they are aligned, then use normal solder for the legs before tidying the up the pins to remove any excess solder/bridges. Flux makes this easier if there's a lot of extra paste. Before using paste, I used to drag solder the pins. It did the job, though the clean up could take a while. If you give this a go, I would say don't be afraid to bridge the pins to begin with, but try to keep the solder as close to the pads as possible. If you get a solder bridge near the plastic housing, you'll end up melting into the plastic trying to clean it up.
@funkyfoo71421 сағат бұрын
@@qubitstech you're awesome man!
@aidenlittle26172 күн бұрын
Can you use that device to connect your controller to your PlayStation? I connected all of my controllers to my friends PS4 and when I tried to connect them to my PS4 using the cable that came with console the controller with blink once like it was going to charge but turn back off I would on and off when I would disconnect it and reconnect it. I’ve even tried resetting the controllers but they still don’t work, I’m hoping it will connect using the cable that came with PS4 if it doesn’t I don’t know what else I can do
@qubitstech23 сағат бұрын
Unfortunately not, the EXT port does not provide a data connection. If you're willing to open the controller, you can get replacement USB boards for a reasonable price (the USB board is separate from the main board) - just be careful plugging in the cable to the USB board.
@aidenlittle261722 сағат бұрын
@@qubitstech Thank you I really appreciate it🙏🙏🙏
@puta9506 күн бұрын
Thanks for nothing🎉
@erikportalatin65414 күн бұрын
Thanks! Freaking Great Video right to the point I saw this with a memory card that I had from buying a ps2 from a lady for $15 about 2 years ago and all I had to do was put it back in place just from watching your video the ps2 sadly doesn’t work with disc they had a lot of Free McBoot stuff on the memory and the hard drive
@SCIMI_CLAN18 күн бұрын
Bro finally found what we need it for
@Webbsy18 күн бұрын
There are 2 pins that look to be about 1.5mm tall that hold the bottom of the PCB. It's almost like it's made to intentionally break over time imo
@sequoiadupree736719 күн бұрын
(I have the red one lol) I’ve been having a problem with my controller. It was working just fine when I first bought it, but then after a bit it just stopped working. It just wouldn’t charge for some reason no matter how long I left it plugged in for. I haven’t used the controller for a good couple years because of that. I was never sure if it was something on the inside of the controller or the charger cord itself. And yeah, it’s the original cord for the rock candy controller. Do you have any idea as to what the problem might be??
@qubitstech23 сағат бұрын
Sorry for the late reply, only just seen your comment. I'd check the battery voltage first of all, and if it's low, use an external charger to charge it. Check all wires etc. as it's possible a wire has come loose. It's hard to say for certain, but if it's unusable, you have nothing to lose opening it up.
@MainNigoki21 күн бұрын
Thank you!
@grumps594028 күн бұрын
Just ordered one of these off eBay, which linux distro do you recommend for the Dell Wyse 3040? I'm assuming my go to of Pop!_OS is too large for the 8GB, although I will probably have a Samsung t7 connected at all times.
@qubitstech23 сағат бұрын
Sorry for the late reply, only just say your comment. I use Gentoo with a USB drive for extra storage (with /usr and /var/tmp moved to the USB) and it works well. If you want something lightweight, antiX seems to do the job, but really anything should be fine if you're willing to use the USB drive for the OS. The internal storage is slow anyway, so you won't really be losing anything.
@Wanderlust_ReaperАй бұрын
Been looking for a tutorial and this is the first one with the same model of controller
@alpha2999Ай бұрын
Nice video, idk why you have so little views on it. Keep up the good work.
@qubitstechАй бұрын
Thanks :) Think it's just luck of the draw sometimes with what youtube wants people to see
@RamaRama-ko4dpАй бұрын
I would try it if there wasn’t any problem and that is THAT I DON’T HAVE ONE OF THESE AND EVEN IF I HAD IT MY PS4 CHARGER IS BROKEN
@JaydenFuller-qs9wyАй бұрын
what if the rubber button piece falls out
@PoltraiteАй бұрын
Excellent. Managed to open mine, clean it and sort out sticky the buttons.
@JaydenFuller-qs9wyАй бұрын
what kind of screwdriver do i need to use
@domantlen6231Ай бұрын
Has anyone tried to use external USB drive with 3040 5V version? Will 5V 2A power supply be enough to power it? Or powering from full (19V powered) terminal?
@qubitstechАй бұрын
Hi, I've just tested with a 4TB seagate barracuda. The system drew 8W max during boot, so you might get away with a 2A power supply though it could struggle under load.
@domantlen6231Ай бұрын
@@qubitstech Awesome! Huge thanks for trying this out! What power adapter did you use?
@qubitstechАй бұрын
No problem, I used an Anker 511 (rated up to 3A) with a type C to barrel jack converter
@d3luxyАй бұрын
Wow thanks for the video. Boards out of stock though. You getting more anytime soon? Also do you ship to South Africa :]
@qubitstechАй бұрын
There's more on the way, though they take a while to get here. I'm happy to sell to South Africa, just be aware that postage is quite expensive, and any import fees/taxes are extra.
@chrismifsud7154Ай бұрын
Its sold out :(
@qubitstechАй бұрын
More are on the way, should be back in stock soon :)
@Ilyeslepro885Ай бұрын
thank you very much. nacely explained
@qubitstechАй бұрын
Thanks :)
@6MetalHead66Ай бұрын
It just won't take charge
@shahzadkhurram7483Ай бұрын
What kind of this chip or usb?
@enzeldiondomingo6469Ай бұрын
THE NAME OF THE USB???
@coenkonieczny4207Ай бұрын
I was quite excited when I noticed that the mod chip was back in stock on your KOFI, but to my disappointment, I noticed you do not ship to Australia😢, is there a workaround?
@qubitstechАй бұрын
Hi, I've added Australia as a shipping option now if you're still interested. Just be aware that shipping is expensive, even though the board is tiny, and you'll have to consider any import fees that would be due. If you know someone locally that can do the soldering, it would probably be cheaper to order the PCBs yourself and get them assembled. Always happy to offer the option though :)
@user-ur2en8it3yАй бұрын
nicely explained. after the replacement my keyboard isn't powering on
@JacindatheGreatАй бұрын
Worked for me! Was able to get both of mine working after being in-storage for 10yrs
@qubitstechАй бұрын
That's great to hear :)
@FreddieMareАй бұрын
I have exactly the same hat on three pi5's but one of them just will not see the ssd or rather pcie lane where am I going wrong or where do I look for a good resource?
@qubitstechАй бұрын
Hi, sorry for the delay getting back to you. If you still have the issue, I'd start by reseating the cable, and swapping it with one from another Pi. If that doesn't work, I'd switch the drive with one that works, to see if that's the issue. It appears not all drives are supported, so that could be the problem.
@FreddieMareАй бұрын
@@qubitstech Hi thanks for the responce appreciated I did som digging and seems the PI5 have a dead pcie port I swoped every thing and tested all combinations posabel and this one pi5 just will not show the pcie post to be active. I send the PI in for inspection by a PI Shop will see what they find.
@ultraprimez2 ай бұрын
can we use a cooler based nvme M.2 drive to it with Rasberry Pi 5 8 gb.
@qubitstechАй бұрын
Probably not with this board, there's very little room between the bottom of the Pi and the drive. The short cable means you can't add larger standoffs either.
@MomoKakashi2 ай бұрын
Firstly thanks for god then thanks for you that was incredible it worked from the first try
@qubitstechАй бұрын
That's great to hear :)
@ajitakhetle67292 ай бұрын
Can we use m.2 slot for external lan card I want to use it as mikrotik router
@qubitstech2 ай бұрын
Honestly I doubt it, you'd need a LAN card which uses SDIO which I'm not sure exists. If it does, you'd struggle to get 100Mbit/s out of it. I'd say give the USB 3.0 port a go, or look at using something with more expansion ports (preferably with PCIe available). Hope this helps :)
@ahmeddubox2 ай бұрын
Thank you very much!
@qubitstech2 ай бұрын
No problem :)
@precisionxt2 ай бұрын
I have about 3 of these units (luckily the 16gb versions). Tiny 10 and 11 do run on it ok, but you’re probably better off with a linux distro. You can supposedly add additional storage using the SDIO port port with an m.2 to MicroSD card converter. I don’t know about I/O speeds using this method, but it at least allows you to keep everything internal and save the limited emmc storage for the primary OS.
@qubitstech2 ай бұрын
Thanks for the comment, I haven't tried Tiny 10 or 11 yet but assumed Linux would probably be better. We have a video testing out the storage mod, To be honest, it's not really worth the hassle, it's not the most reliable mod. A USB drive is probably the better option if more storage is needed.
@PKENDIKАй бұрын
I have one with Dietpi running Pihole. Very much recommend
@yash_arАй бұрын
@@PKENDIK Is there a video on how to install that? I got one of these through a friend, I'm trying to make it work, it didn't have a WiFi card so I installed one but it didn't work, im assuming it needs the driver? Sorry I am somewhat novice with this and pc in general, but I'm learning
@PKENDIKАй бұрын
@@yash_ar not really no, you will have to burn image to pen drive, install dietpi, and then install pihole. I may get a guide done
@yash_arАй бұрын
@@PKENDIK Thanks, let me know if you do that 🙏
@afccarl19942 ай бұрын
I've just done this mod to my dock, it works really well and fits perfectly. Thanks 😊
@qubitstechАй бұрын
That's great, glad it worked for you :)
@gaborszucs89352 ай бұрын
Im really eyeing one of these up thinking of running windows XP on it. Would it be somehow possible?
@qubitstech2 ай бұрын
Probably not. This only supports UEFI booting, while XP has no UEFI support. There might be ways around this, but it's not something I've ever tried. You're also likely to have issues finding drivers, though the basic Windows graphics driver might be enough to get a display output. Would be interesting to hear your experience if you decide to give it a go :)
@MattKucia2 ай бұрын
I host home assistant on one of those. Ran out of the space quickly as 8Gi version gives you around 2Gi. Moved all my home assistant stuff to the USB storage without any performance hit (so far).
@qubitstech2 ай бұрын
I'm planning to use one for home assistant, so I'll probably end up doing the same. I think it helps that the internal storage itself is pretty slow - if you have a decent USB drive, you can probably match it.
@bartmanfantanfart362 ай бұрын
Who do I ask for so.one to fix my memory card and controller The memory card connector chip looks corodded
@kasparkasevali9812 ай бұрын
Thanks a lot, worked well, might have to do it for x soon lol
@qubitstech2 ай бұрын
Glad it helped, not tried it with the X button though so not sure if it will work. If you do try it, let us know how you get on! :)
@DEN-iq7qn3 ай бұрын
Bro thank u, my headset wasn’t working so i unplugged the battery the plug it back and its started ❤️❤️
@qubitstech2 ай бұрын
Glad I could help :)
@Rhettroizms3 ай бұрын
Is there a way to put this in the gamepad, because the charger is the one thing I HATE about the Wii U. Near flawless system
@qubitstech2 ай бұрын
There's plenty of room inside the gamepad so it would definitely be possible. That would mean risking the gamepad though, so it's not something I really want to do. You can buy generic type C charging boards quite cheaply, one of those should be enough if you can find a good place to mount it.
@Lou1s-m3 ай бұрын
No one talking about how that controller comes with a ps4 that worth more than the ps5
@coenkonieczny42073 ай бұрын
could you please release the, (PCB file) so I can try and get through PCBway. Because your store has been out of Stock for a while :(
@bryanteugenio24623 ай бұрын
what usb is that?
@zatozeon3 ай бұрын
Thanks! The plastic brace for my chip was worn down just enough to hold its position for reassembly, but not enough to withstand being plugged in. It's bizarre your chip had no support at all. I wonder how many functioning cards have been tossed in the trash because of this...
@qubitstech2 ай бұрын
No problem, glad I could help. I agree it's weird, no idea how it ever worked at all :/
@declanheerey37763 ай бұрын
THE usual tinkering was required to get my Raspberry Pi and the NVMe drive to work together. Basically I did something. I changed something. I repeated something and I restarted something and well in the end something I did got it working...something....the next time it'll more than likely be something else or something different. Just saying.....it's worth trying.......something!!!
@jaydenheags1613 ай бұрын
Thanks 🙏
@handlescom3 ай бұрын
What’s it called
@paulwalker4273 ай бұрын
Great video
@qubitstech3 ай бұрын
Thanks :)
@sadr-yt3 ай бұрын
thank you my A button is working but now i have another problem: my controller isnt working, like when i plug it in, the light above the xbox button is off
@Hiwired963 ай бұрын
Cool mod!
@qubitstech3 ай бұрын
Thanks :)
@clodomirvianna63503 ай бұрын
Thank you very much for this video! It helped me fix my headphone that had very low volume on the right speaker after I accidentally dropped it. In my case the cause seemed to be a loose connection.
@qubitstech3 ай бұрын
Glad the video helped you out :)
@ellis_10463 ай бұрын
Do you know where I can find the replacement parts for a PDP controller? I need a new button pad but I can only find the one for the regular xbox controller (doesn't fit)
@qubitstech3 ай бұрын
Unfortunately not, we couldn't find any either which is how this mod came about. Only thing I can suggest is trying to find a cheap faulty one to use for parts, or maybe contact PDP to see if they can help (I doubt it though).