I was looking at this but on the website it says that it wasnt compatible with my truck. I have the 2022
@Jh3454-df5vm11 күн бұрын
Is there a video for the 4in air ride lift kit for a 2017 rebel?
@serbel853514 күн бұрын
Hello ! How much does this kind of work and this kit cost for a 2014 Tundra?
@JonLIsALoser27 күн бұрын
What offset do you have one these wheels
@CourtneyPorter-gm6wi27 күн бұрын
Does BDS know what a torque wrench is.
@energyefficient2247Ай бұрын
Do you know where to get a Service/Shop Manual for the Air Suspension System for a 2015 Ram 1500 Sport?
@user-uq2vu9le8dАй бұрын
👍👍👍
@johnmcdonald3696Ай бұрын
You have to be a NASA engineer to install this.
@goatsmakesoapco.9113Ай бұрын
The 3" is not listed on your website???
@bdssuspensionАй бұрын
3" C/O Kits will be up on the website soon, keep an eye out for upcoming announcements
@peternguyen9602Ай бұрын
I have a 7 inch bds lift on my tundra and it only sits about 1 3/4 inches higher than my 3 inch rough country level ? Is that just how they sit or ? I didn’t install my bump stops cause I didn’t see the need for it cause I don’t off-road is that why it sits so low?
@bdssuspensionАй бұрын
When installed properly this kit nets a full 7" of lift up front over the stock ride height. Bump stops won't effect ride height and we offer this kit in both a 4.5" and 7" lift height. Its difficult to diagnose over the internet, so I'd suggest starting with taking ride height measurement (center of hub up to the top of the fender opening) along with some photos of the front suspension installed and reach out to our tech support team to verify ride height and figure out what's going on, [email protected]. You can also connect with them over the phone as well at (517) 279-2135
@user-xn3pv7bd5wАй бұрын
I just got a 2017 colorado zr2 extended cab,does cab difference has effect on the lift kit?will this lift kit work on my truck thats my main concern .Moneys ready for doing lifting and big 35”tires
@bdssuspensionАй бұрын
cab configuration doesn't effect the kit fitment, this kit will work on there
@giobarajas3654Ай бұрын
2 lifted ram 2500s
@johnambrose1030Ай бұрын
What about the drip bracket for the trans line, my bracket doesn't seem to match what I have, it has two holes and a stud which don't match the bolt diameter of stock mounting location.
@user-bt2dr6is9wАй бұрын
Awesome truck & truck built , seems like I have a long way to go in order to get it overlanding ready Lol. But sweet build.
@JoshuaCarbaughProductions2 ай бұрын
BDS, I can’t find a shop who is willing to put in the labor or time into this lift. I went to your site, searched in your “find an installer” tool and none of them will do this lift. From Southeast Missouri, anywhere you all have a good working relationship with that will do this lift?
@shiningstaer2 ай бұрын
Is there a 4th gen video? Would the install be similar?
@MrChevySrh2 ай бұрын
2 questions for ya. Any reason you don't just remove the caliper completely since you're replacing brake lines anyway? Then, is there a reason you don't just remove the spindle completely before removing the wheel bearing? Starting mine in the morning and just curious.
@rileylong29182 ай бұрын
Will 38’s fit on 17x9’s? 13.50 wide
@Jh3454-df5vm2 ай бұрын
Is there a full video for a 2017 ram with air ride available
@Av8er642 ай бұрын
Did I miss where you did anything to the adaptive headlight sensor brackets?
@shaneh7342 ай бұрын
Awesome work and description!
@chinito20fam2 ай бұрын
Well you guys ever do one but for a 2003 dodge ram a quad cab.. want to take it to Mexico and have fun. Get it fixed up and know i habe a amzing setup
@idontcaresapo82332 ай бұрын
What’s the best set up for when your driving on the street?
@danielcastorena30572 ай бұрын
So what happened with the long travel kit for chevy? Were in 2024 now 😢
@patrickjames10802 ай бұрын
cant find the air struts on your site - are they still available?
@andrewjarvis77772 ай бұрын
Not a toyota rip
@kandg82772 ай бұрын
I have no idea why BDS has this child, who knows nothing about trucks or parts doing this podcast who memorized her lines
@FuturesTrader2 ай бұрын
Thanks for sharing - sweet setup
@Spitfire12622 ай бұрын
Is this a Hemi or Cummins? Still running the short control arms up front? Just curious about the ride. I have a 2013 SLT too on 37s and it feels really stiff even with softer springs.
@seangowan74413 ай бұрын
Can your coilover lifts be installed on gas trucks?
@BC_Hunter3 ай бұрын
Beauty!
@Max_ellis743 ай бұрын
If I get a tundra with 4wd and wanted this exact lift do I need to weld anything?
@anonymoususer89133 ай бұрын
Does your 6inch lift kit for 2012 f150 and nx2 shocks (1950$ish) come with a strut spacer or a new strut. I have seen both but thanks
@Nathan-gy7oz3 ай бұрын
Can you specify which Ridetech components you used? I just ordered the BDS 6in coilover system with the 2.5s as well and would like to add the air system.
@ColdWarVet6073 ай бұрын
Nice touch having the grease fitting and top of the ball joint covered with a cap. at first look I thought these might not be greasable.
@rickyfoley42943 ай бұрын
The short wide wide. 🤌🏻
@begaxbega27853 ай бұрын
Sick .
@alonzogracian56153 ай бұрын
Nice truck
@dougv4643 ай бұрын
I installed myself on a 2021 GMC Denali in six part-time days in my home garage. I’m retired from a major research and development company so I’ve seen my share of product designs and I was very impressed with the fit of the components in the BDS kit. I’m curious if BDS used geometric dimensioning and tolerancing (GDT) to design these parts. I’d like to see a better procedure for setting the ride height of the upper control arms that doesn’t require repeating so many steps. Also like to see BDS work with Fox to develop a non-Reservoir shock for the Denali assuming ARC delete.
@alejandromonreal-ramirez17373 ай бұрын
Hi There, Question. Do you have to cut the front crash bar on the truck with the - 18 off set wheel ?. I thinking going with the same set up but I looking a wheel with -24 off set. I know the with the -24 I have too.
@pat14lang3 ай бұрын
Is it sitting at 8”? It looks a bit taller than 8”
@claytonkeyes70413 ай бұрын
Sic wit it 🥶
@maxgrande25084 ай бұрын
Greatly appreciated: This is a great tutorial video.
@user-dq3jk9py4q4 ай бұрын
What bumper did you use for sd126? Fit perfect with the 6" McNeill fenders. I cant find any that fit this well. Thank you
@dafuq92554 ай бұрын
Awkward
@SuperdutyExplorer4 ай бұрын
Im just starting to build my F350 out! Truck stock atm... but got my "camper" useabe, but after a few trips, I want to change a few things... thinking about the 4inch lift at some point! I'll see if i can have money for lift/rims/tires saved up by next year!..
@greg213321334 ай бұрын
Damm that’s a good video. I’d let this guy work on my truck anytime
@nicocastillo75244 ай бұрын
I have 20x10 wrapped in 35x12.50 and stock I get some slight rub here and there just waiting for the lift to get powder coated and I doubt I’ll rub once it’s on