#023

Рет қаралды 5,462

Күн бұрын

This video is for the Fujifilm community but not only, if you want to know what's inside a Fuji mirrorless camera just watch this video and thank me later.
Also consider subscribing and share it with everyone.
DISCLAIMER:
CameraRestore is not responsible for property damage or injury incurred as a result of the information contained in this video. CameraRestore recommends safe practices when working with power tools and electrical equipment, use of lubricants, liquids, expensive electronics, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of CameraRestore, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not CameraRestore. Only attempt your own repairs if you can accept personal responsibility for the results, whether they are good or bad.

Пікірлер: 51

@yudhariswan1486 5 ай бұрын

helpful video, i recently my xe2s always get reset every time i took off the battery, and when i see your video there is internal battery on the motherboard, is there any chance i can replace it with the new one? if it so whats type the battery did the camera use?

@noliiiivaldez7861 2 жыл бұрын

my locking pin is stuck on my xt100, thanks for taking apart the x mount, i am confident now what to expect when i unscrew the thing.

@CameraRestore 2 жыл бұрын

Thanks! Good luck with it. If you need any suggestion on that, just drop a message here.

@doksdavaudoo9075 4 ай бұрын

`thank you. great video, i used it to change the lcd....would have been a hassle without you

@billo5 4 ай бұрын

Amazing video thank you! Unfortunately my Xe-2 internal battery is dying so i have 4 seconds to change the main battery before all my settings default to factory. Do you know what internal battery does the Xe-2? Can't find any information. Thanks in advance!

@sn0rbaard 2 ай бұрын

Did you ever find out?

@billo5 2 ай бұрын

@@sn0rbaard no, in the end i just returned it. it was already soo expensive for a 10 year camera, so it didnt make sense to keep it and open it up.

@JesusCorrea_ 2 жыл бұрын

thanks to your video the canon 1300D can change the shutter of mine, thanks, I was wondering if you can make a video about the NIKON D7100 a friend has that camera and it is damaged too

@CameraRestore 2 жыл бұрын

Hi thanks, I have some other project that I'm working on, but I will consider the D7100 when available

@johncarlosalangsang6511 Ай бұрын

Hi. I hope you reply to this comment. May I know what capacitor does the XE2 have?

@MrTwixraider 2 жыл бұрын

Thank you, the video is great. My display started flickering today and now I wanted to see how to replace the display. It seems to be feasible for me. The only question I have is where do I get the adhesive sealing strips to glue the new display back in place?

@CameraRestore 2 жыл бұрын

You’re welcome, thanks. If you’re interested, I have the LCD and usually I send it wit the needed adhesive.

@arkjiang Жыл бұрын

is it common for the EVF to go bad ? only LCD working, EVF sensor works but no longer turns on

@CameraRestore Жыл бұрын

Not common issues but might happen.

@nyomanambara7711 Жыл бұрын

Hello sir, can you help me answer my question. Is it the same lcd screen XE2 X100T and X100F? I googling about the specs is the same lcd screen 3" 1040k dot. Because i try to replace my X100F lcd screen with XE2 lcd part replacement. Thank you for the answer sir

@AndreaGarcia-nj2nq 7 ай бұрын

Would you be able to do and show button repair for the Fujifilm XQ2?

@CameraRestore 6 ай бұрын

I'm sorry, but I do not have any experience with point and shot cameras...

@tedvitale8978 11 ай бұрын

Brilliant! So, I have an XE1 that stopped turning on. Most of what Ive read says its probably the motherboard and after some basic trouble shooting I feel like it is. So I have 2 questions, first, is there a good place to buy aftermarket boards, and is it worth replacing because ive seen notes about the boards still needing to be calibrated by fuji after the install, and second between the xe1 and 2 is the disassembily about the same as whats shown here? Ive only ever seen one other disassembally of an xe1 and it wasnt as in depth as this.

@CameraRestore 8 ай бұрын

Best would be to get a second hand one, from another Xe1 basically, avoid Chinese ones, are crap.

@Ib3119cz 2 жыл бұрын

AMAZING DUDE!...ONE QUESTION ...I HABE PROBLEMS WITH THEBACK SHUTER SPEED DIAL..I DOES NOT RESPONSE SOMETIMES.IT GOES WELL WHEN YOU PRESS IT TO MAKE ZOOM BUT IT DOES NOT GOES RIGHT WHEN YOU WANT TO CHANGE THE SHUTER SPEED .ANY SUGGEST?...THANKS SO MUCH

@CameraRestore 2 жыл бұрын

Thanks. This is a common problem with those dial wheels on Fuji’s. Not an easy way to fix either, the easy way is to replace the top circuit board… Another one would be to spray some electronic cleaner trough the wheel space and then moving the wheel back and forth for a minute or more but that’s nasty and doesn’t work every time…

@wrongbeta 2 жыл бұрын

Thank you for the amazing video. Just what I needed it! Do you have the replacement for the lcd screen by any chance?

@CameraRestore 2 жыл бұрын

Thanks, I might have it, drop me a mail at contact@camerarestore.co.uk

@user-me5ck5ns5d 11 ай бұрын

Hy, how did you stick again the first protection you have removed ? Sorry for my english 😊

@CameraRestore 8 ай бұрын

If you means the leather, has a double tape and if you warm up and carefully remove it after will stick back without problem.

@BartechTV 2 жыл бұрын

Is it possible to further disassemble the sensor module, to remove dust trapped between the sensor and the glass covering it?

@CameraRestore 2 жыл бұрын

It's enough to take the tree little screws off, you can see it at minute 54:14:00 I would highly recommend to work on an empty table and possibly completely clean room at least 30 minutes before you open up the sensor. Usually this operation require an extremely clean room, specifically made for this kind of work.

@camfixer 2 жыл бұрын

Great video! One question. The 'battery latch' (the red/orange battery retaining clip} on my X-E2s is broken. Does the whole battery compartment need to be replaced as I don't think this clip is available seperately from Fuji. Thanks in advance for your reply.

@CameraRestore 2 жыл бұрын

Thanks. Yes, you will need to replace the whole box. I have the part in stock, drop me a message at contact@camerarestore.co.uk if you're interested

@pacopablo1000 Жыл бұрын

sorry to bother you, but i've had an issue with 2 different fujifilm cameras (xe2 & xt1 ) , they stopped switching on , without any evident reasons. the only thing that comesi in my mind is that i've shooted some commercial pictures in a quite dusty ambient (marble workshop).there is any chanche to disassembly the camera and try to clean the power switch ? Many thanks in advance M.

@CameraRestore Жыл бұрын

Ciao Matteo 😉 Marble dust is very abrasive, if gets inside may create some damage. One thing that I noticed is that the switch power is quite sensible and tends to fail easily. The only way is to open up the camere and investigate, might need a microscope or a watch repair loupe to see in details the conditions. Not easy work to be honest, lots of steps to reach that point…

@Angeloso_RPM 2 жыл бұрын

Is it possible to remplace the viewfinder without soldering?

@CameraRestore 2 жыл бұрын

Do you mean the 5 wires of the top that are soldered to the mainboard?

@Robanjo 2 жыл бұрын

Hello! Very nice video! I just got a xe2 for 80$, everything works except evf, apperntly the camera bumped against something and the evf went black. Im thinking maybe check if cable has come loose first? Is there shortcuts to getting to the evf?

@CameraRestore 2 жыл бұрын

Hi Robin, check your inbox.

@franzjosefstakes 2 жыл бұрын

@@CameraRestore I have that same problem, my X-E2 EVF doesn't work after in bumped into something - can you help me aswell?

@CameraRestore 2 жыл бұрын

@LeonidasGFX Hi, the guy above got the replacement from me. I should have another one on stock if you’re interested…

@emanuelschi Жыл бұрын

Hello, my xe4 turns on, but the lcd just lights up in black. When turned off again, the lcd stayes on. Only by removing the batterie it (of course) stops working. Do you have any idea what could be wrong? Thanks fpr your help! :)

@CameraRestore Жыл бұрын

Hey, did your camera had any kind of water contact? Looks like a motherboard fault…

@emanuelschi Жыл бұрын

@@CameraRestore Thank you for answering! not that I know off... so it might be a total defect probably?

@CameraRestore Жыл бұрын

@@emanuelschi Might be the case, a checkup could tell better what could be wrong.