#025

Рет қаралды 6,307

2 жыл бұрын

This is probably one of the most detailed teardown of a digital camera you will find on YT, you should save this video as a tutorial for every time you need it. In order to reduce time, probably on the next videos I will not put on evidence so many details. An amazing piece of engineering, considering it was made in 2009. Hope you like it and you do appreciate my work.
Parts available here: bit.ly/3PpYepo
If this video helped you, consider to support my work too. A symbolic coffee could make the difference:
www.buymeacoffee.com/CameraRe...
Also consider to subscribe and share it with everyone.
DISCLAIMER:
CameraRestore is not responsible for property damage or injury incurred as a result of the information contained in this video. CameraRestore recommends safe practices when working with power tools and electrical equipment, use of lubricants, liquids, expensive electronics, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of CameraRestore, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not CameraRestore. Only attempt your own repairs if you can accept personal responsibility for the results, whether they are good or bad

Пікірлер: 29

@CameraRestore Жыл бұрын

Hey guys, check out my stock of parts for this camera here : Canon 7D parts : bit.ly/3PpYepo Also for canon 7D Mark II here: bit.ly/3SJDHNq Hopefully I'll be able to add a teardown for 7D Mk II soon the stock is quite limited, so make sure you grab what you need before it gets away!

@Michael-er3qh Жыл бұрын

A superb video. Thanks.

@CameraRestore Жыл бұрын

Glad you liked it!

@SA-gk8dc 2 жыл бұрын

Antique camera 😳 Great content mate!

@CameraRestore 2 жыл бұрын

Thanks 👍

@The_Great_Won Жыл бұрын

Thank you for this step by step video. Its a lifesaver!!

@wahyubindep8803 2 жыл бұрын

Nice video

@CameraRestore 2 жыл бұрын

Thanks

@GrainlessVideos Жыл бұрын

What type of tape are you taking off at 1:09:44 (1/2inch, 1/4inch)? What type of phillips screw driver are you using (#0, #0-1,#0-2)? What type of prying tools are you using? What type of tweezers are you using (metal or plastic)? How do you align the image sensor on reassembly?

@MikeJones-oo7wi Жыл бұрын

Excellent video, just what I've been looking for. Q. How does one discharge the capacitor?

@CameraRestore Жыл бұрын

Thanks, you will need a 20k OHM 5w resistor, I recommend adding some extension wire to avoid touching any exposed wire.

@MikeJones-oo7wi Жыл бұрын

@@CameraRestore thanks! For the reply.

@mdam2254 2 ай бұрын

After I shoot a few images or a few seconds of video I get a error 70 or error 80 any idea what the defect is?

@filipepais1540 Жыл бұрын

This video is absolutely brilliant, thank you so much for such good contributions. While replacing the card reader slot, my autofocus function stopped working. Then I realized through your video that some of the cables in the board located on the bottom of the camera (where the capacitor sits), are actually connected with the AFocus. By reconnecting some of them the AFocus function started working again, but after putting back all the screws in the camera, the AFocus stopped working again, and I stop seeing any red lights in the viewfinder. I have rechecked again many times all of the connections on the motherboard and bottom board but the Afocus never worked back again. Do you have any clue on what may be the problem? Thank you so much!

@CameraRestore 9 ай бұрын

You might have had shortcut the board, did you discharged the capacitor?

@filipepais1540 8 ай бұрын

no, but in the meantime, i've changed the camera, thank you very much for answering @@CameraRestore

@sagauer Жыл бұрын

Is the procedure for removing the screen different for the 6D? Is the 6D also glass? Thanks!

@CameraRestore Жыл бұрын

Is different, have a look here: Canon 6D Step-by-Step Disassembly - How to Service and Repair kzfaq.info/get/bejne/o6xhrNZ206vFpHU.html

@ljjonesy 7 ай бұрын

Great video, can you please tell me what is the material used for the bottom tripod screw plate? Is it a painted alloy or solid polycarbonate? Just purchased a near mint 7d with a scuff mark bellow the grip, thinking about using some 1000 grit wet and dry to smooth it out...

@CameraRestore 7 ай бұрын

Bottom is poly, will make it worst, don’t bother and have fun taking pictures 😉

@ljjonesy 7 ай бұрын

@@CameraRestore Will do 👍

@tivadarbobok932 2 жыл бұрын

HI, can you please help me with the following. I have a 7D. After may years of service one of the screw from the bottom pcb went into the camera. After that the camera stopped working at all. I found the screw, put it back to its place but unfortunately the screw must have shorted something in the camera. Even I found all 3 boards (dc-dc, bottom, main) visibly faultless, I do not know how to test them. I have a multi-meter only. Can you please tell me if the is any way to sort it out. I do not want to order them blindly to determine which one is the faulty one.

@CameraRestore Жыл бұрын

Damage from a loose screw can be very dangerous and in some cases irreversible, can easily compromise the mainboard. A multimeter is not enough to score the issue without an electrical diagram, and manufacturers keeps that very secret to the public. This is quite hard, but one thing that you could do, is to buy a dummy battery for your camera, with the multimeter set-ed to mAmps connect it in line with the positive wire of that dummy battery, power the camera from an external source (you could use a battery, wired properly) and see if you get any power drained from your camera. Or use a powerbank and will show the readings. I might make a video for this sometime, so sty tuned ;)