#025

No video

#025

Рет қаралды 6,745

CameraRestore

Күн бұрын

Пікірлер: 30

@CameraRestore Жыл бұрын

Hey guys, check out my stock of parts for this camera here : Canon 7D parts : bit.ly/3PpYepo Also for canon 7D Mark II here: bit.ly/3SJDHNq Hopefully I'll be able to add a teardown for 7D Mk II soon the stock is quite limited, so make sure you grab what you need before it gets away!

@SA-gk8dc 2 жыл бұрын

Antique camera 😳 Great content mate!

@CameraRestore 2 жыл бұрын

Thanks 👍

@The_Great_Won Жыл бұрын

Thank you for this step by step video. Its a lifesaver!!

@ianmclyde 10 күн бұрын

Hi, what are the 2 flex cables at the bottom of the main board called? The large one and little one below the image sensor flex cable. Mine are broken so need to find replacements. Thanks 😊

@Michael-er3qh Жыл бұрын

A superb video. Thanks.

@CameraRestore Жыл бұрын

Glad you liked it!

@GrainlessVideos Жыл бұрын

What type of tape are you taking off at 1:09:44 (1/2inch, 1/4inch)? What type of phillips screw driver are you using (#0, #0-1,#0-2)? What type of prying tools are you using? What type of tweezers are you using (metal or plastic)? How do you align the image sensor on reassembly?

@mdam2254 3 ай бұрын

After I shoot a few images or a few seconds of video I get a error 70 or error 80 any idea what the defect is?

@MikeJones-oo7wi 2 жыл бұрын

Excellent video, just what I've been looking for. Q. How does one discharge the capacitor?

@CameraRestore 2 жыл бұрын

Thanks, you will need a 20k OHM 5w resistor, I recommend adding some extension wire to avoid touching any exposed wire.

@MikeJones-oo7wi 2 жыл бұрын

@@CameraRestore thanks! For the reply.

@wahyubindep8803 2 жыл бұрын

Nice video

@CameraRestore 2 жыл бұрын

Thanks

@ljjonesy 9 ай бұрын

Great video, can you please tell me what is the material used for the bottom tripod screw plate? Is it a painted alloy or solid polycarbonate? Just purchased a near mint 7d with a scuff mark bellow the grip, thinking about using some 1000 grit wet and dry to smooth it out...

@CameraRestore 9 ай бұрын

Bottom is poly, will make it worst, don’t bother and have fun taking pictures 😉

@ljjonesy 9 ай бұрын

@@CameraRestore Will do 👍

@filipepais1540 Жыл бұрын

This video is absolutely brilliant, thank you so much for such good contributions. While replacing the card reader slot, my autofocus function stopped working. Then I realized through your video that some of the cables in the board located on the bottom of the camera (where the capacitor sits), are actually connected with the AFocus. By reconnecting some of them the AFocus function started working again, but after putting back all the screws in the camera, the AFocus stopped working again, and I stop seeing any red lights in the viewfinder. I have rechecked again many times all of the connections on the motherboard and bottom board but the Afocus never worked back again. Do you have any clue on what may be the problem? Thank you so much!

@CameraRestore 10 ай бұрын

You might have had shortcut the board, did you discharged the capacitor?

@filipepais1540 10 ай бұрын

no, but in the meantime, i've changed the camera, thank you very much for answering @@CameraRestore

@sagauer Жыл бұрын

Is the procedure for removing the screen different for the 6D? Is the 6D also glass? Thanks!

@CameraRestore Жыл бұрын

Is different, have a look here: Canon 6D Step-by-Step Disassembly - How to Service and Repair kzfaq.info/get/bejne/o6xhrNZ206vFpHU.html

@tivadarbobok932 2 жыл бұрын

HI, can you please help me with the following. I have a 7D. After may years of service one of the screw from the bottom pcb went into the camera. After that the camera stopped working at all. I found the screw, put it back to its place but unfortunately the screw must have shorted something in the camera. Even I found all 3 boards (dc-dc, bottom, main) visibly faultless, I do not know how to test them. I have a multi-meter only. Can you please tell me if the is any way to sort it out. I do not want to order them blindly to determine which one is the faulty one.

@CameraRestore 2 жыл бұрын

Damage from a loose screw can be very dangerous and in some cases irreversible, can easily compromise the mainboard. A multimeter is not enough to score the issue without an electrical diagram, and manufacturers keeps that very secret to the public. This is quite hard, but one thing that you could do, is to buy a dummy battery for your camera, with the multimeter set-ed to mAmps connect it in line with the positive wire of that dummy battery, power the camera from an external source (you could use a battery, wired properly) and see if you get any power drained from your camera. Or use a powerbank and will show the readings. I might make a video for this sometime, so sty tuned ;)