IMPORTANT: There is another 7mm screw right next to the Round Knob. Once you pry the Round Knob off you also need to remove the 7mm screw right next to it. Not sure why it's not shown in this video.. I'm guessing they practiced before filming and forgot to put it back on before they shot this video. I just replaced my front two seat bottoms on my 2005 Expedition Eddie Bauer and there was a 7mm screw on both sides right next to the Round Knob which is only visible once you pry the Round Knob off. I actually broke the tab/hole on the side trim piece on the first seat I did because I wasn't looking for another screw. Hope this helps someone avoid the same mistake. The rest of the video was extremely helpful! The seat covers were an exact color match, despite my Expedition being 17 years old, and the quality was EXCELLENT. I would HIGHLY RECOMMEND these seat covers!

I obtained this product because of this video. I followed the instructions exactly as demonstrated. The result is a perfect restoration without any complications. A better replacement could not exist; even the color does not put the other seats to shame, but is an excellent match despite 14 years of use. I am more than satisfied with my purchase.

The cushion fit perfectly and the install video was a great help. I got a call to confirm I was getting the right cushion, which shows great attention to customer satisfaction. One item I would like to suggest is that the video to install this particular cushion was on KZfaq, but not referenced in the list of videos on the web site. It took me extra time to locate it and I think there is no reason why it should not be locatable via your site directly. I also missed the 7 mm screw behind the lumbar adjust knob and busted the side cover attach point.. I tried epoxying the little piece back, but it got busted off again when trying to reinstall the cover over the seat back tilt handle. However, not having that screw does not effect the seat.

Great I have to take the seat out first? Yay.

A couple of points. 1. To remove the shield that has the power seat controls or manual controls, you need to unclip the front cover clip and there is a T20 torx screw that screws off. Once off, you can pull on the shield and get it off the seat. Instead of monkeying around with the screws you see him unscrewing at 2:45 from the shield, unclip the power connectors. On my Limited there are 2 power disconnects. 2. At the end it shows him clipping all the cushion clips to the seat. DO NOT clip the front one until you have the power/manual controls shield back in place. Otherwise you will not be able to put the T20 screw back in until you unclip the front clip.

I purchased the driver side bottom & Durafoam for my ‘05 Expidition. It’s exactly the same as the one on the “how to “ video. I’m glad they posted this video because it made it for an easy decision to purchase the items. The springs cut thru the old foam. I recommend purchasing the foam if you have an older model. Looking forward to replacing the passenger side next.

Great help! I bought my seat cover from these guys and followed these instructions to the letter. There were only two problems that I worked around. 1. Ford wrapped the original two straps that Velcro together on the back of the seat in a felt. I just cut through it. 2. The original clip that holds the front of the seat cover to the bottom steel frame of the chair is different from the one that came in the replacement cover. I put epoxy in the clip in the new cover and left it to dry overnight. Hopefully this will hold the clip on the frame.

Very helpful video. Thanks for posting. Well done

Hey Thanks guys, I did this on my 2003 Explored EB. The only problem I encountered is now the seat belt light stays on, but no sounds ( thankfully ) I did reinstall the small metal washer on the rear right bolt to secure the ground, but lite is on. I'm not going to worry about it. Thanks again, saved me $300 USD

Thanks! It sure is easier when I'm in my shop with nobody else there! I can practice inventing new cuss words on some of these jobs. LOL

gooooooooooodddd…..👌👌👍

wish you would cover how to change the seat foam in this vid as well

What about replacing the actual bottom cushion too ? Is that possible ? Bought a used 03 and the left side is completely smashed down flat. Thanks

Hey guys awesome vid Merry Christmas >real quick will seats in a 2007-2009 sit 2003 -2004 expedition?

Hi!! I need a video on replacing drivers backrest leather cover

Do you have a video for a 2006 Ford Explorer?

Is there a video for the top replacement?

I am ready to do this, however, what if the T-55 Torx bolts twist off?? I got under the unit and could not really find the seat bolts going through the body, ( gas tank, and 4x4, and tranny stuff in the way) to try and spray em down, with penetrating oil.

There is a 7mm screw behind round knob

I would say that the leather is not all that but after 225,000 miles there is no rips or tears but just wore out. Feels more like pleather than leather

Nice! Is it necessary to remove the seat from the floor bracket in order to replace the seat cover? If not, what difficulties is there when doing while the seat is in the vehicle? Thank you.

why don't you have the 06 lincoln navigator cushion with ac vent?

Do you have 07 Expedition Eddie Bauer, two tone grey and camel perforated replacement

Anyone know where to get these. They are discontinued now?

Why hunter look terrified

How much for top and bottom? I have exact SUV front seat 💺

Is it possible to remove the seat cover without removing the seat from the truck?

Is possible to do it with the seat in place?

Does the cushion come off easy?

Why no cloth two tones grey

Where are you guys located?? I need to replace the driver bottom seat cushion and cover!!

..so... It's a real nightmare to install

I bought the fake leather seat bottom on eBay for around $47-$48......and I TOTALLY REGRET it!! What a POS that cover is. My advice to anyone looking to swap seats. Find one that fits better and spend the extra bucks.

thumbs down since your company specifically linked this video to a foam bottom replacement after somebody asked for the video. And this only shows the cover replacement

You guys are over priced