Thank you for going over the resizing ring. Could not find anything that explained it the way you did!
@theshotgunscientists Жыл бұрын
Thanks man
@ronaldjohnson14746 ай бұрын
Nice! Straight forward presentation. Thanks.
@theshotgunscientists6 ай бұрын
Thanks man.
@Wigeon3211 Жыл бұрын
Last season steel shotgun shells became difficult to buy and doubled in price. As a life time loader for clays I just never loaded for ducks. Don’t want to go thru having to scrounge for duck loads and pay twice the price again. I’m going to get busy reloading some ducks loads for the fall! Thanks for the video.
@theshotgunscientists Жыл бұрын
Luckily everything you’d need is currently available
@Navyuncle7 ай бұрын
BP had their steel shot on sale. I believe that it was in 10 pound bags. Check their website.
@Wigeon3211 Жыл бұрын
Thanks for what you are doing! Could you put the recipe pinned in the comments? Thanks again for what you are doing!
@smartacus885 ай бұрын
Wade Rush has got a 3in steel BB load using 33 grains of Longshot with a TPS pre slit wad that i am assuming is a 3in shell wad because the load is 1 1/4th ounce and sits flush with the top of the wad. I don't believe he uses any additional nitro cards or fiber wads etc. Just powder, TPS was, shot, crimp. I mention this because you said in the video that stack hight might be an issue with Longshot powder?
@theshotgunscientists5 ай бұрын
Longshot takes up a lot less room
@tntphillipians41346 ай бұрын
Where did you get your load data for these shells ?
@theshotgunscientists6 ай бұрын
Alliants website
@clks11654 ай бұрын
I have two loads i like to see tried out. It come from the new tps wad data 2023. For one is in 2 3/4 cheddite hulls, ched209 primer, 23 gr longshot powder, Tps1275 wads, 1 1/8 oz steel shot going at 1250 fps with 10,800 psi. The other one is a 3" cheddite hulls, ched209 primer, 29 gr longshot powder, tps1230 wasds with a 1/4" felt wad under shot with a over shot card, 1 1/8 oz steel shot going at 1350 fps with 11,000 psi.
@theshotgunscientists4 ай бұрын
That first load is something I’ve actually done a video on a couple years ago. People seem it like it. I used crossman bb’s.
@clks11654 ай бұрын
@theshotgunscientists but that one was 1oz load, not 1 1/8 oz
@clks11654 ай бұрын
And yep, that 2 3/4 " load is an awesome load
@clks11657 ай бұрын
That is a good duck load. I was wondering if you could try that loads load (1 1/4 or 1 1/8 oz), but with longshot or hs-6 powder?
@theshotgunscientists7 ай бұрын
Longshot develops pressure spikes a lot faster with steel shot. It can be done but the velocity would suffer.
@clks11657 ай бұрын
@theshotgunscientists more velocity doesn't really kill. If it 1200 to 1350 fps, that should work.
@tripplebeards3427 Жыл бұрын
Thinking of trying my 3oz 10 gauge loads with some flax seed and or corn cob media. How will it tighten my patterns on average? I put clear nail polish over my card board shot cards to try and waterproof them myself…reposted because I don’t know if live chat was working.
@theshotgunscientists Жыл бұрын
Those are filler materials used over the shot to get better crimps actually
@user-qp3eb4pm1zfatcatreloading Жыл бұрын
Good video. 👍
@theshotgunscientists Жыл бұрын
Thanks man
@mickluther2693 Жыл бұрын
Have you ever loaded any 2 3/4 in 1 1/8 oz steel loads?
@theshotgunscientists Жыл бұрын
Yes
@CoopDawgg216 ай бұрын
What reloading manual do you recommend for reloading steel shot 3” for waterfowl?
@theshotgunscientists6 ай бұрын
Status of steel
@clks11655 ай бұрын
Can you try 1 3/8 oz steel shot in 3 " s hulls and 28 to 29 gr alliant steel powder? Note that tps1230 will fit 1 3/8 oz
@theshotgunscientists5 ай бұрын
What’s the full load data
@clks11655 ай бұрын
@theshotgunscientists it comes from the alliant 2000 data, but that one was a 1 1/2 oz load, but know that alliant steel had changed a bet since then, and I also checked out the new tps data and looked at both the 1 1/8 oz and 1 1/4 oz load to get the exact charge of powder with 1 3/8 oz load to be in safe psi
@mikehunt43148 ай бұрын
I’m looking to load some steel/tss 3” 12ga, I have ched hulls, ched 209, longshot, and tps 42 wads, just wondering if you have any insight on that load and about how much powder to stay within safe pressure ranges.
@mikehunt43148 ай бұрын
Going for 1 1/4 oz payload and a roll crimp
@theshotgunscientists8 ай бұрын
I’m not sure man I’ve never messed with that wad
@Badreload Жыл бұрын
What do you think the best roll crimped to get started roll crimping thanks
@theshotgunscientists Жыл бұрын
Reloaders network 4 pin is by far the best one on the market unless you get one of the gaep bn series but those are expensive. The reloaders network one puts a very nice taper on your shells and will even roll crimp shells that have a fold crimp on them.
@robertfrapples2472 Жыл бұрын
@@theshotgunscientists I bought two of the Reloaders Network 12ga 4 pin roll crimpers over a year ago. I've made hundreds of rounds with one of them, keeping the other as a backup. So far, the first one is performing as well as the day I bought it. Highly recommend. I don't have a Gaep, but hear they are phenomenal. I do much more fold crimping than roll, so I never found it a justifiable purchase. What part of KY are you in? I'm in Louisville, about 9 miles from Knob Creek Range. You should swing by and pick up Scott from KY Ballistics and Buffalo from Buffalo's Outdoors, and bring them out for a day of mayhem with me! Lol.
@theshotgunscientists Жыл бұрын
@@robertfrapples2472 I’m in Grayson about 30 minutes from Ashland. Just below Ohio and west Virginia. I have the RN roll crimp tools in 20 and 16 gauge they are awesome. Best on the market I believe. Gaep is on a different level though. I ain’t seen the need for one though.
@robertfrapples2472 Жыл бұрын
If you can afford it, go with the MEC Jr. instead of the Lee Load-All. I have both, and there is no comparison. On the Lee, the stationary pre-crimp obliges you to align the pleats with every round. You can't make adjustments for shot column height other than "hand pressure" on the lever. The whole press leans at an angle when the lever is depressed, that often causes a slant to the top of your shells. Lastly, that resizing ring is a real pain, especially if you misplace it. The Lee will get the job done, but "not horrible" is not the quality I'm after. I do enjoy the videos you boys put out. Please watch those pressures!
@theshotgunscientists Жыл бұрын
I’ve used mec presses and don’t like them. I’ve been using the Lee load all for 4 years and get great looking crimps out of it. I don’t think mecs are anywhere near as versatile, I’ve got lees in 12, 20 and 16 gauge, and a converted 12 gauge kit that does 10 gauge. I can also load 2.5” shells with them without having to adjust anything at all. I also fold crimp my 24 and 32 gauge shells with them with the help of chamber inserts as a final crimp tube. I also have 3d printed kits for the Lee load all in 28, 24, 32, 10 and .410. The taper crimp die I have on my 10 gauge press is awesome. I’ve got a bolt on depriming punch for 3.5” shells that’s mounted right to one of them. Basically a whole new station. I just like my Lee presses, they put out great crimps if you know how to use them and I’ve got about 200 bucks into them and some add ons that allow me to crimp all 8 different gauges I own. We’ve barely ever ran into any pressure signs, typically speaking we stay away from max powder charges or high pressure loads due to unavailability of components right now. It’s almost impossible to follow a load recipe piece by piece these days. We also test new components out that don’t have data available hardly. The trick is to start low with powder charges if you aren’t sure. I can think of only 3 times we’ve ran into pressure problems but nothing serious, just some primer flow back here and there but most of that is due to mossberg shotguns having huge firing pin holes.
@robeveridge83297 ай бұрын
Will this work woth cheddite or fiocchi hulls?
@theshotgunscientists7 ай бұрын
Yes
@clks11655 ай бұрын
Do you have Hercule/Alliant 2400?
@theshotgunscientists5 ай бұрын
Nope but I can get it locally
@clks11655 ай бұрын
@theshotgunscientists I have a Requested load I love to see tried out. It comes from a mec steel shot load data from 1994 copy. It uses 3 " winchester supper X hull basic base wads, fed209a primers, 42 gr Hercules/Alliant 2400 ( I try 39 gr if needed to use ched209 primer), mec12 3" which are now the precision reloading tuprw123 wads, 1 1/4 oz of steel shot going at 1260 fps at 11,500 psi.
@clks11655 ай бұрын
@@theshotgunscientists I got 3 cans of it and was curious to see you try this load
@general-Lee-700 Жыл бұрын
Bro you guys got to do a hunting video
@theshotgunscientists Жыл бұрын
One day for sure. Hardly anyone hunts waterfowl where we’re at.
@general-Lee-700 Жыл бұрын
Quick question you think you can make a video on how to make a three inch shell hold two different kind of loads?