12ga 3” 1.5oz Simple & Effective Bismuth Hand Load with Patterns

Рет қаралды 4,713

Күн бұрын

This is a simple and effective 12ga Bismuth handload. The goal of this project was to get effective bismuth patterns using readily available components.
This video is for informational purposes only. This is not published load data and is not advice or instruction on correct loading information or practices. Load at your own Risk. This is non-published load and is not intended to be used as so.
Load:
12ga 3” 1.5oz Bismuth
CX2000 or win209 primer
3” Ched Hull
31.8gr Hodgdon LongShot powder
WAA114 wad (flare gas seal) or CB1114 wad
1.5oz of Bismuth
30gr of PSB buffer
OPTIONAL- use Mylar wrap in shot cup to protect pellets
If you want to support my channel, go to my eBay store by using the following link:
www.ebay.com/usr/the10man-35?...

Пікірлер: 21

@mikeholston9263 5 ай бұрын

Thank you for the info and getting back with me.

@avidwaterfowler7522 5 ай бұрын

That’s what I’m here for.

@mrsmith9079 10 ай бұрын

Very good patterns, definitely good enough for serious work. On your point about TSS - you can load down to the 7/8 -1 ounce payloads in a 20 gauge and the cost of the shot isn't all that dissimilar to that of bismuth in a 10 gauge load. 1 ounce of TSS 8''s have ~ 250 pellets next to ~200 in 2 ounces of bismuth 2's, and the tungsten pellets will hit harder. You could even move up to 7's and you'd still have ~184 pellets, with enough punch to kill anything out to 100 yards.

@avidwaterfowler7522 10 ай бұрын

Funny you brought up TSS in those exactly payloads for the 20ga. I ordered 4lbs of 7.5’s to experiment with. You get around 225 pellets in an once. My plan was to buy 7’s but they weren’t available at the moment. If TSS does as well as I’m hoping, I’ll be making 7/8oz 8’s and 1oz 7’s.

@mrsmith9079 10 ай бұрын

@@avidwaterfowler7522 I managed to pick up 2kg of 7's too, in hindsight I should have gone with 8's given how 7's are apparently equivalent to FF sized steel. I look forward to seeing your review of your tungsten homeloads!

@AndrewHouse-mj9qr 10 ай бұрын

Great video, those are good looking patterns. I’d love to see you Win Xpert clone as well

@avidwaterfowler7522 10 ай бұрын

I’ll add that one to the list!

@mikeholston9263 5 ай бұрын

Can a blue Rio 3 inch hull be reloaded using same recipe as a 3 inch Cheddite hull ? I was given a bunch of Rio once fired hulls.

@avidwaterfowler7522 5 ай бұрын

Straight wall is straight wall in regards to Hulls as far as I’m concerned. What I would base it on is internal volume. Use something to measure the inside height and compare it to the cheds you have. Odds are you can use those Rio with no problems.

@HawkEye02088 6 ай бұрын

How has longshot preformed for you in colder weather? Like low 20s or teens temperature, even single digits. Any differences in FPS?

@avidwaterfowler7522 6 ай бұрын

Long shot has been good. I don’t use it as much as other guys do (I’m more of an alliant guy). It has done well in cold weather and I have not had an issue yet. The thing that I don’t like about LS is it can be a little spikey with pressure and it’s known for it.

@deputyja1 9 ай бұрын

Why'd you go with WAA12F and not WAA12R? I apologize for my ignorance just new to reloading hunting loads and trying to learn

@avidwaterfowler7522 9 ай бұрын

So I went with the 1-1/4oz field wad over the 1-3/8oz field wad because the fill is about perfect if you load on a mec. If you use a Lee load all like I did for these couple, you can’t get the crimp as tight without creasing the shell. Basically I’m trying to get stack height correct. I sometimes do tests with the load all because I don’t need to fiddle around with set up.

@deputyja1 9 ай бұрын

@@avidwaterfowler7522 sounds good. I have both and was just curious

@michaelcavazos3671 8 ай бұрын

What payload are we looking at in a 2.75 hull?

@avidwaterfowler7522 8 ай бұрын

1.25oz is the standard. I run 1.5 in 3”.

@goldwp2 3 ай бұрын

Where are you buying your Bismuth Shot from?

@avidwaterfowler7522 3 ай бұрын

Mostly rotometals and I also like plated BPI bismuth, but not the budget bismuth.

@goldwp2 2 ай бұрын

@@avidwaterfowler7522 have you thought about making your own bismuth shot?

@michaelcavazos3671 8 ай бұрын

What the cost of bismuth 12 ga 3inch 1 1/4. Is it worth the investment of getting into the reloading thing.

@avidwaterfowler7522 8 ай бұрын

I would not load 1-1/4oz of bismuth in a 3” shell, just go to 2-3/4”. As for cost, you would have to get costs of all components you plan on using. I would have to guess you could load those for about $1.50ish a shell or less depending if you reuse hulls or not.