18 Volt & 20 Volt Battery Upgrade for Power Wheels with Low Voltage Cut Off
Рет қаралды 22,073
Күн бұрынTHE MATERIAL LIST IS BELOW
Using a drill battery to upgrade your child's Power Wheels is fun, but if you aren't using a Low Voltage Cutoff protection, it can be dangerous for the battery and your child.
The video showed a Low Voltage Cut Off of 14.5 and a Reset rate of 4.5, on a 18/20V use 16.0 volts as a cut off and 1.0 for the Reset.
Low Voltage Cut Disconnect rates:
12 Volt battery: set the cut off between 9.0 and 9.9 / Reset Rate: @9.0 cutoff use 1.0, @9.9 cut off use 1.0 (Recommended 9.9 volts; Reset 1.0)
18 & 20 Volt battery: Recommended cutoff is 16.0 volts; 1.0 Reset
MATERIAL LIST:
Below are the items and links to the products I have used in the video. Note, as an Amazon Associate member, I earn from qualifying purchases. If you purchase through Amazon, you can help support this channel just by purchasing through the links.
24v relay (with wire connectors, so you wont need to drill a holes) amzn.to/3SJ4Kw5
Low Voltage Cutoff Board:
amzn.to/3QSDtVw
12 Gauge Wire: amzn.to/47jBNv6
20 Volt Battery (your choice of course): amzn.to/3zyZcY0
Battery Charger: amzn.to/3kSKhE3
Wire Connection Kit: amzn.to/3iI0uJr
Terminal Block: amzn.to/3rw7YDz
12 Gauge In-Line Fuse: amzn.to/2UEYdqG
You will also need a Wire Stripping tool ( amzn.to/3zsme2E ) and Wire Crimping tool (amzn.to/3zyZxde )
@DadHacks 3 жыл бұрын
Recommended Cut Off Voltages: 12 Volt - Set at 9.9 Volts, 1.0 Reset 18/20 Volts - Set at 16.0 Volts, 1.0 Reset
@TGA2010000 2 жыл бұрын
Is this setup good for your kids remote rc control mod?
@DadHacks 2 жыл бұрын
@@TGA2010000 I would say no, because the RC setup is good for when the kids are under the ages of 2 or two-and-a-half. And if I’m running a RC setup with a young kid, I don’t want the car to go 7mph. I would recommend using a SLA battery over a power tool battery on a RC setup because the runtime is usually longer
@TGA2010000 2 жыл бұрын
@@DadHacks thank you very much for the advice...I will definitely look into sla battery setup
@paulturner8801 2 жыл бұрын
Followed your video step by step and gave new life to a very old power wheel jeep. Thank you for this! Very well done. I love learning about electronics and trying new things.
@DadHacks 2 жыл бұрын
Great to hear!
@123cardude 7 ай бұрын
Thank you so much for this video! I was so confused on the low voltage controller and why it wasn't working. But when you explained the math of it, it made sense and it worked mediontly. Thank you for saving my project!
@lukeo85 Жыл бұрын
How would you wire it for two batteries and two low voltage cut off switches? Would I need two relays?
@davidbeerbower5731 10 ай бұрын
When I attach it to the power wheel with the cut off board, the second speed (faster) for forward studders and will not actually go. When I do it without the low voltage cut off board attached, it works fine. Any ideas?
@trevorgehman 2 жыл бұрын
Do you have an alternative recommendation for the 24v relays to buy? The one you link is out of stock.... I like the prewired connectors. Trying to make it as easy as possible for myself...
@DadHacks 2 жыл бұрын
Here’s another link to a 24relay with a harness. (I like them prewired as well, so much easier to use) www.amazon.com/dp/B07QLD857Z/ref=cm_sw_r_cp_api_glt_fabc_NHQ2HS4B8F7HGYN17N1J
@mxktm68 2 ай бұрын
Have everything wired just as shown with same equipment but my out side of my LVCO does both have an illuminated led light and i am getting no voltage on my multimeter, but i am not sure where the problem is coming from.
@_DeFiNiTeLy_Not_BrAd_ 2 жыл бұрын
How would you wire it if you wanted to add a PWM controller to prolong the motors? I was going to wire it the same way with the controller between the battery and terminal strip output, but i seen in the comments you said the PWM controller needs full power to work correctly?
@DadHacks 2 жыл бұрын
Watch this video, I have the diagram at the 4:19 minute mark. kzfaq.info/get/bejne/ip-AiLZ1sayvcYE.html
@annamisner7632 Жыл бұрын
The relay you have linked in the description is not available. Any other recommendations of one that would work?
@DadHacks Жыл бұрын
I’ll update the link for this relay. The main thing is that’s it’s a 24 volt relay with a harness. Thanks for letting me know a.co/d/08wZEvO
@BU10AS 5 ай бұрын
You confused me when you say you will not need to use 87-A on the relay but then you connect it to the + car's power input. Does using two battery have advantages? I bought parts for doing that but not sure if I need to? May do another power wheel car later, so extra parts will be okay. You video's are outstanding!
@DadHacks 5 ай бұрын
Thanks! I try to make the videos easy to understand. I neglected to explain that a 5 pin relay has an 87 pin and a 87A pin. The 87A is located in the middle and is unused. The “87” is located on the outside of the relay and is used. Thanks for asking, I’ll be sure to clarify in the future!
@NealORussa Жыл бұрын
If adding a motor voltage controller, would you add it after the line that says "to car" or before/after the fuse going into terminal 30 on the relay? Wanting to be able to control speed, or reduce voltage out to motor down to 12v instead of 20 or 18.
@DadHacks Жыл бұрын
I have a better diagram to use with a voltage controller in this video, around the 4 minute point: kzfaq.info/get/bejne/ntRydKimu-CrdXU.htmlsi=pmGHWQzlBpRoZJ8C
@caliking369 8 ай бұрын
@@DadHacks hey I tried clicking on your video but it says private 😢
@DadHacks 8 ай бұрын
Sorry, try this link kzfaq.info/get/bejne/ntRydKimu-CrdXU.htmlsi=pmGHWQzlBpRoZJ8C
@trevorgehman 2 жыл бұрын
Does it matter if the fuse is before going into the relay, or can it alternatively be on the wire going out of the relay to the car? I assume it's fine, but just wondering...
@DadHacks 2 жыл бұрын
Ideally you will want it before the relay. If something were to happen then you’d have to replace the relay and a fuse versus just a fuse.
@Relyks583 3 ай бұрын
Followed your video step by step with a dewalt 20v battery. Hooked it up to the jeep and it works but it’s super jerky and when you left off the peddle it’s a pretty delayed abrupt stop. Also the jeep had a little radio and would do the engine start up sound but neither of those work when I switched it over
@DadHacks 3 ай бұрын
The 20 volts likely fried the radio and lights (if it had any)
@Relyks583 3 ай бұрын
@@DadHacks used it a little bit today and those randomly started working again. Took it for a test drive and it lasted around 10 mins then it would kind of sputter on and off a lot. It was set to the 16 and 1 like you specified. There’s a high and low speed but they’re the same now to for some reason.
@matthewchase6418 2 жыл бұрын
Hi, i plan on running two M18 batteries in paralell. I have the LVC and a DC speed controller. Im thinking i wont use the LVC and monitor the voltage on the cars built in radio. Do you think this is acceptable? I really dont want to reset the LVC every time i change a pack. The exisiting wire in the car is 16awg its one of those chinese ride ons with the lights etc. The battery adapters come with 30A fuses. I plan to upgrade the cars control board in time. There is also a 12v breaker thing between the battery + and the board.
@DadHacks 2 жыл бұрын
Yes, using the dashboard voltage is perfect. I’ve moved away from the LVC board and just use a digital voltage gauge. If the car had a control board (little black box), then it will need to be upgraded to a 24 volt Weeley RX30. Otherwise, you are all set.
@matthewchase6418 2 жыл бұрын
@@DadHacks awesome, my daughter is still small so i plan on keeping the pwm controller no higher than 14 or 15v. When she is bigger i plan on swapping to the 24v board and motors for more speed. I do worry about the stock wiring being able to handle the full load though.
@cyb3rFac3z 2 ай бұрын
Hi @DadHacks, thank you so much for your video!!! 🤩 I'm about to start the project and was wondering if using the blue crimp with a 12awg wire is okay. I found online that the yellow crimp is more suitable for this size of wire. I have no knowledge of electricity and I don't want to compromise safety. What do you advice? Thanks a lot 💪👍
@DadHacks 2 ай бұрын
Thanks! The blue connectors will likely have a hole that’s too small to fit a 12 AWG wire. It’s better to got either the yellow
@cyb3rFac3z 2 ай бұрын
Thank you for the reply. I've another question about the fuse (from a newbie lol). Why did you place one between the terminal block and the relay and not directly on the positive wire from the battery? I thought that it would be more secure next to the battery to avoid any fire risks? Or maybe do you suggest to place two in line fuses in the system (battery and relay/lcvd?)
@DadHacks 2 ай бұрын
@cyb3rFac3z I should have placed the fuse closer to the battery. You’re learning quick
@cyb3rFac3z 2 ай бұрын
Thus, if I've understand well, it's better to move the fuse closer to the battery and I have a regular wire between the relay and the lcvd?
@DadHacks 2 ай бұрын
@@cyb3rFac3z yes, move the fuse closer to the battery, before the split to the LVC board
@MrBetovolador 4 ай бұрын
hello , the 24v rele works with 15v for example if I use a 18v battery? If I have a cutoff of 14 v?. Thank you
@DadHacks 4 ай бұрын
Yes a 24v relay will work when the battery voltage drops to 15 volts. I’ve found setting the voltage cutoff at 16.0 works best for the battery
@MrBetovolador 4 ай бұрын
@@DadHacks tank you so much...
@roydiaz4618 Жыл бұрын
How do you add the speed selector using that set up?
@DadHacks Жыл бұрын
Checkout this video, it uses a speed controller kzfaq.info/get/bejne/ntRydKimu-CrdXU.html
@jamesm8360 2 жыл бұрын
Im useing 2 / 20 volt craftsman batterys 6 ah. Can i piggy back the 2 batterys on the strip? Both positive and then both negitive together. Or would this not be correct. And is 2 fuses needed for both batterys just before the strips? Im trying to understand how low voltage relay is protected, it looks like the 1 fuse is after the relay. I would think the fuse should go on the red positive side IN of Low volt cutoff. Im most likly looking at it wrong as far as following the lines. Thanks for your professional advice, i will be doing this project soon, thankyou. Im installing a speed control unit as well, its not in your plans, im going to install it from low volt control board to speed control unit. Thanks!
@DadHacks 2 жыл бұрын
I would wire the batteries in parallel before wiring them to the strip (red to red/black to black). This will give you 20v and 12Ah. You can then add the fuse before the strip. Technically, that would be the only fuse needed and would be before the relay and LVC board to protect both. One note of the Craftsman battery, it is possible that it could already have a LVC built into the battery, similar to Ridgid, Ryobi and Makita. But it never hurts to have extra protection for the battery. Lastly, I have another video that hits wiring up the speed control unit on Method 4 of this video kzfaq.info/get/bejne/ntRydKimu-CrdXU.html
@jamesm8360 2 жыл бұрын
@@DadHacks Thankyou for reply. Can I just add 2 fuses to battery's before the strip and on the strip hook up both black and both positive wires for the 20v 12ah for this to safe guard system. This way I will have 2 20 Amp fuses protecting system. Thankyou for your time, much appreciated.
@DadHacks 2 жыл бұрын
Yes. For that method you are correct to use 2 fuses. FYI, the speed control that I bought had a mini 30 amp fuse in it, and it kept popping so I had to replace it with a 40amp. Make sure you are using at least 12 gauge wire
@jamesm8360 2 жыл бұрын
@@DadHacks Thankyou very much. I have a better understanding now. Have a great day. I'm very grateful for your help. I'm a sub to your channel!
@ff-mu6cc 7 ай бұрын
cool!
@davideby13 Ай бұрын
Late to the upgrade party but I was watching this and I was trying to figure out, is the relay required and/or what exactly does it do?
@DadHacks Ай бұрын
The low voltage control board can only handle 20 amps. The power wheels motor will draw more than that on grass or going up a hill, so that will fry the control board. A relay sends voltage to the board to power it without sending the full amount of amps.
@davideby13 Ай бұрын
Thanks for the reply! I wasn’t sure what to expect with it being an older video but i really appreciate the clarification! Sounds like not by-passing steps is the smart way to go.
@Jakbkwik1 Ай бұрын
I purchased the exact parts from the links, hooked everything up exactly the same but when I push the accelerator on the car I get nothing but a buzz from the relay
@DadHacks Ай бұрын
What car brand do you have?
@MrThornton81 2 жыл бұрын
What are the relays for?
@DadHacks 2 жыл бұрын
To protect the Low Voltage Cutoff board, it can’t handle the full load. You could skip adding a LVC board and relay, but you would need a digital voltmeter to keep an eye on the voltage
@nickm7394 Жыл бұрын
You have any issues with the low cut off board shorting out?? Both mine went out day after I installed them. Not sure if the kids let the bottom of the board touch metal and they went out or there is another issue
@DadHacks Жыл бұрын
Nope, I haven’t had any issues with the LVC board when used with a relay.
@nickm7394 Жыл бұрын
@@DadHacks Both the LVC boards went out on the first day. (2 power wheels) I followed your diagram exactly, yes including the relay. The red light indicator is off on both boards and when I checked with a volt meter there is no power coming out of the board.
@DadHacks Жыл бұрын
@@nickm7394 hmm, any other modifications? Like different motor or bike tire wrapped around the wheels?
@nickm7394 Жыл бұрын
@@DadHacks no, none of that stuff yet. I did test run night before , daughter drove both power wheels around a while. Then came home yesterday and kids told me they arent working. One of then the fuse blew (the fuse on the wire) pop the new fuse in ran for 3-4 min then died. Check it and no power coming out of the board, same as the first board. So maybe bad luck and both faulty or maybe the back of the board touch metal and shorted out?? I got 2 more on order today
@annamisner7632 11 ай бұрын
How do you connect the two wires that go to the vehicle? Do you have any pictures of that? I have 4 wires coming out of my power wheels.
@DadHacks 11 ай бұрын
What kind of power wheels is it and what type of battery does it use (6 volt, 12 volt or two 6 volt)? I’ve seen 4 wires on a Kid Trax motorcycles before. If you have an old battery, take a look at this video kzfaq.info/get/bejne/bsqWdtOJpq2yhqs.html
@annamisner7632 11 ай бұрын
It is a 12 volt Jeep Safari. And I sadly don’t have an old battery for it. It has black, white, blue, and yellow wires coming out of it and into the original plug.
@DadHacks 11 ай бұрын
@@annamisner7632 how old do you think the car is? Like less than 10 years or more than 10 years old?
@DadHacks 11 ай бұрын
@@annamisner7632 I’m pretty sure the 4 wires were for a two battery set up. Two 6 volt batteries, and they could switch between low (6 volts) or high (12 volts). To be honest, it’s a very difficult setup to convert to 18 volts
@annamisner7632 11 ай бұрын
@@DadHacks We got it from our neighbor, but I’m guessing older?
@nikanddeepspanchal2251 Жыл бұрын
What is the relay doing in all this?
@DadHacks Жыл бұрын
It’s taking the load draw so that it doesn’t have to run through the LVC board
@KPRS Жыл бұрын
How can I get ahold of you? I got some questions on why I can’t the speed to go up after installing 3 Pcs Power Battery Adapter Converter Kit Includes Motor Speed Controller with Switch Battery Power Adapter Low Voltage Protection 40a Fuse for 18V 20V Batteries DIY Display Toys Robots Cars. Need some help.
@DadHacks Жыл бұрын
You can email me at GoGoPoweredWheels@gmail.com , Include links to the stuff you bought and the type of car you have.
@bradburton4426 2 жыл бұрын
Does this low voltage board store the settings? I have a few ride on toys that are running drill batteries, some for years without an issue, but going deeper down the rabbit hole lead me to realize how wrong I have been doing it. Right now, my kids will just hot swap the batteries when one is dead. If they pull the battery wont the board reset? I know I wouldn't have the issue if I left the battery in the toy and recharged it there (not ideal), or If I ran 2 batteries the board would have power as I swapped them one at a time.
@DadHacks 2 жыл бұрын
Unfortunately, I’m pretty sure these boards do “reset” when power is disconnected, meaning it’s up to the child to reset it if they swap out batteries. I’ve switched to mainly using a digital voltage gauge on the dashboard to monitor the voltage, then swap out as needed
@jasons1034 2 жыл бұрын
@@DadHacks can you link which one you are using? And by this do you mean rather having a cut-off board, you just now have a voltage reading aka A "gas" gauge and when you start to reach the safe "empty" zone, you stop and swap? I'm getting ready to do two conversions for my boys and there's no way they are going to set the cut off switch every time they ride if the voltage board doesn't retain it's settings but if I give them a digital "gas" tank with a number to not go below, I'm pretty sure they would remember it's time for a pit stop.
@DadHacks 2 жыл бұрын
Yup, I use the digital voltage gauge as a “gas” tank for the battery. Funny enough, there is usually a gas tank sticker that I install the voltage meter over. Here’s the link to one I’ve used. If you have questions wiring it up, just let me know. I usually run it down to 16.0 volts, that leaves some room if we need to drive back to the garage. a.co/d/hHXyBBr
@jasons1034 2 жыл бұрын
@@DadHacks thanks so much for quick reply. Yes, need help on how to wire in and where in the chain does this go? I see that it only has two connectors so how would I add this to chain? Right now my plan was not to use a terminal block - I was going to go Battery-voltage cutoff- speed control-motor. Would I need a terminal block if I went just meter reader?
@DadHacks 2 жыл бұрын
You won’t need a terminal block, but you will need to split each line (positive and negative). From the battery, you could wire into this splitter (for example positive 1 wire in, 2 positive wires out). a.co/d/ismrZ8z . One of the 2 out lines would go to the volt meter and the other would run to the “in” of your speed controller. Then the “out” of the speed controller would run to the car. The wire size from the battery, to the speed controller and then to the car should be 12 AWG. You can use a 16 AWG wire for the volt meter
@jayl5265 2 жыл бұрын
How long would this run before dead?
@DadHacks 2 жыл бұрын
Between 30 to 45 minutes. Some factors that effect run time are the driving surface (pavement vs grass) and the weight of the car and driver
@archand1 6 ай бұрын
I purchased this exact set up but also bought a speed controller. How do i connect it to this setup?
@DadHacks 6 ай бұрын
I have another video with a speed controller. Skip to 2:50 on the video and then 4:20 (ignore those links as it links to the current video) for the diagram for this video kzfaq.info/get/bejne/ntRydKimu-CrdXU.htmlsi=eXm_QbslqBvpxkvg
@archand1 6 ай бұрын
@@DadHacks thank you!
@archand1 5 ай бұрын
For the low voltage board...what connectors are you using? It's such a small opening none of mine fit?
@DadHacks 5 ай бұрын
@archand1 12 AWG wire can fit well if you “open” up the connection area when you unscrew it all the way
@archand1 5 ай бұрын
I got that to work thanks. And sorry to be a pest...I have the exact setup from the diagram you showed me with speed controller. I'm getting power to LVC and speed controller. But, no power to car. It's a Perego Gator...does it have 2 speeds plus reverse have something to do with it? No blown fuses etc.
@petersnng 11 ай бұрын
what relay model did you use?
@DadHacks 11 ай бұрын
You can use a 24 volt / 40 amp 4 pin relay. a.co/d/7OmMpjw
@petersnng 11 ай бұрын
thanks really helpful@@DadHacks . im trying to wire up a 24v, 4 motor 4x4 power wheels, with a speed controller, low voltage cut off and ryobi battery adaptor.
@Erosennin450 2 жыл бұрын
If I don’t use that low voltage cut off module Do I still need the relay?
@DadHacks 2 жыл бұрын
Nope. The relay is only used to protect the LVC board
@Erosennin450 2 жыл бұрын
@@DadHacks what if I use one of those pwm speed controllers with the adjustable knob would input a relay in front? Is a relay like a fuse that takes the load so it doesn’t fry circuit boards?
@DadHacks 2 жыл бұрын
The PWM speed controller needs the full load in its input, so you wouldn’t use a relay with the PWM. Also the PWM has a mini 30a fuse in it. I have had the mini fuse pop once or twice, but I put a 40a fuse in it and it did fine. Also note, there was a regular 30a fuse before the PWM’s fuse that didn’t pop, so that leads me to believe the mini fuse is more delicate. So I would still recommend a 30a fuse right off of the battery and then don’t rely on the internal PWM’s fuse. A fuse is a safety tool to protect the wire, the relay is a safety tool to protect a switch or board.
@Erosennin450 2 жыл бұрын
@@DadHacks awesome thanks so much !
@DadHacks 2 жыл бұрын
One thing I should clarify is that the fuse protects the wire from overheating too much. But the fuse can only work if it’s sized correctly. If the stock wires on the car are thin (16 AWG), then you should use a smaller fuse size, like a 20 amp. If you use a larger fuse, like a 30 or 40 amp fuse it will essentially be useless.
@gng1042 Жыл бұрын
You recommend a 5 pin relay, but wouldn’t a 4 pin make more sense?
@DadHacks Жыл бұрын
Yes, 4 pin works
@yanez3231 Жыл бұрын
The LED screen on the low voltage cutoff drains my battery if I forget to disconnect it from the car. SOS
@DadHacks Жыл бұрын
Great comment. Yes, brands like Power Wheels and Peg Perego do not have on/off switch. It’s best practice to always disconnect the battery after use, even on 6v, 12v or 18 volts
@Name-ld4kz Жыл бұрын
Put the whole system on an ON/OFF switch.
@TRISTOM307 2 жыл бұрын
My fuse keeps blowing. I'm running it with one battery. Any ideas?
@DadHacks 2 жыл бұрын
What size wiring are you using? Ideally, you want around 12 AWG
@TRISTOM307 2 жыл бұрын
@@DadHacks I used 12 all the way through
@DadHacks 2 жыл бұрын
Is it happening on pavement or just when they drive on the grass?
@TRISTOM307 2 жыл бұрын
@@DadHacks always
@DadHacks 2 жыл бұрын
@@TRISTOM307 typically, how long does it run before the fuse blows?
@kirbycollins3223 3 жыл бұрын
Can this Setup Be Done in Series?
@DadHacks 3 жыл бұрын
Yes, you could wire the batteries in series, But when you start to push 24volts or more through a Power Wheels, you start to have more problems. Gearboxes tend to be the first thing to break, because the plastic gears can’t handle the heat. Also, the wiring might not be large enough to handle the heat
@kirbycollins3223 3 жыл бұрын
@@DadHacks Yes I Plan to Get the 775 Gearboxes with the Metal Gear?
@DadHacks 3 жыл бұрын
@@kirbycollins3223 the metal will definitely help. Here’s my “please subscribe” pitch; I’m working on a video on how to add a ESC (electric speed controller) and variable speed pedal. The ESC is ideal when running 24+ volts because it causes less stress on the gears and functions like a real gas pedal
@ahlers1977 3 жыл бұрын
Thanks for the video! Any chance you know where I can find a schematic for 2 12v batteries in series with the low voltage cut off? We have a 24v Grave Digger with Banebot motors but the batteries are shot. I brought some milwaukee battery adapters & hooked them up but smoked the low voltage cut off in a matter of seconds. Definitely need a diagram to do it correctly if you know where I can find 1.
@DadHacks 3 жыл бұрын
@@ahlers1977 use the diagram at 5:22 in the video, but for the batteries, the + of one battery and the - of the other connect and then the other + and - run to the terminal strip... FYI, it’s a lot easier if you use the Sealed Lead Acid batteries, you don’t need a Low Voltage Cutoff for those and the time run is better than drill batteries
@Monstarr586 3 жыл бұрын
Nice. Where did you get the cutoff board?
@DadHacks 3 жыл бұрын
Amazon. For $3 more, you can get the 2 pack. Here’s the link: www.amazon.com/dp/B07QNXM4LS/ref=cm_sw_r_cp_api_glt_fabc_Q074VT8JK6J38SD53X2H
@Name-ld4kz Жыл бұрын
You really need to move your fuses to before the bus bar. It's not safe the way it's currently set up.
@DadHacks Жыл бұрын
Agree. The best place for the fuse is right off the battery
@ismaelmagana5184 Жыл бұрын
I’m going to put one before the bus bar and one before the relay too
@DadHacks Жыл бұрын
You really just need 1 before the bus bar
@ejonesss 10 ай бұрын
not just shorten the life of the batteries but fire risk because the chemistry becomes unstable and could start fires. some lithium chemistries can handle it better to really be safe you should go with lifepo4 witch you will simply ruin the cells and they may not last as long. i think this could one of the reasons why hoverboard batteries was catching fire besides shoddy cells, bad welds and shoddy charging systems. and now ebike batteries are catching fire it has been all over the news and youtube news.
@atmanfss1584 Жыл бұрын
Hello, pleas one help, i dont find some parts of gaucho superpower, the electronic card have burned but can repaired, pleas if yu can give me yur whatsapp or email i can show the picture to you, i think yu can help, thanks
Симбочка Пимпочка
Рет қаралды 2,5 МЛН
Torque Test Channel
Рет қаралды 427 М.
Building Stuff Is Fun
Рет қаралды 44 М.
Jasonoid - Solar Power, Batteries, and More!
Рет қаралды 161 М.