1968 Mustang door hinge rebuild. Jade part 37

Рет қаралды 5,254

3 жыл бұрын

In this video I rebuild the passenger side door hinge for the 68 Mustang known as Jade. All went together smoothly. I pan to reinstall the hinges and hang the doors.
My Amazon page: www.amazon.com/shop/jodaddysg...
As an Amazon associate, I earn from qualifying purchases.

Пікірлер: 26

@PR-nq4dt 4 ай бұрын

I also got my set of bushings from cj pony but mine were the hw2948 1965-1968 and are the correct length. Thanks for the tutorial! 👍

@jamessmothers6475 3 жыл бұрын

Great video, one easy tip to install the bushings. Get a bolt , nut, 4 washers it will center the bushings as you tighten bolt and nut the 2 washers on each end act like a makeshift bearing surface. Plus reducing the risk of damaging the new bushings.

@tedbponycars3014 3 жыл бұрын

Nice ! More Jade please

@rickburt7055 3 жыл бұрын

Nice to see you working on your own projects again 👍

@clabe1000 3 жыл бұрын

I put a strip light in my same blaster, its worked great for years also I changed my plastic to glass I cut. last longer

@davidcherylbarch2802 3 жыл бұрын

You did a great job on the hinges and a better job explaining the process of rebuilding them! Keep doing what you do so well and your channel will grow! Big thumbs up!!!!

@greifill 3 жыл бұрын

I rebuilt the hinges on the driver's door 4 years ago. I can't remember if the pins in the rebuild kit had these extra long serrated teeth. Now I have to go and look, lol! Nice burnout at the end!

@clabe1000 3 жыл бұрын

yes they do I also saw this on a falcon I did

@clabe1000 3 жыл бұрын

I did a pair once and they were longer on the serrated teeth on mine, I too cleaned them up

@hectorsarmiento8840 3 жыл бұрын

Excelente video saludos desde Honduras

@clabe1000 3 жыл бұрын

I also hooked up a vacume to back hole

@davebrittain9216 3 жыл бұрын

Hey Barry I have heard you refer to you cut disc as a "zizz wheel" a few times and I wondered if it was a brand or something so I did a search on Google and this is what came up lol. "zizz-wheel Zizz Wheel refers to a woman's ablility to gyrate her pelvis rhythmically in perfect attunement to her lover's thrusts. Hip tilt and "swirl" are other prime examples of this rare and much-sought-after talent." I am not kidding look it up. lol Well you learn something new everyday.

@JoDaddysGarage 3 жыл бұрын

It's a term used in the aircraft industry. At least where I worked.

@gregworkshop5713 3 жыл бұрын

hi barry bnice work i wish mine were that easy .i have to drill mine and read pin wift a roll pin .

@elcam84 3 жыл бұрын

Ooh pretty. Do I need to make a trip out there and put lights in your cabinet? I have a pile of stuff ready to go in the blasting cabinet and get powdercoated in my micro powdercoating oven. Future project is building another big powdercoating oven for the shop.

@JoDaddysGarage 3 жыл бұрын

I'll buy the pizza.

@jcook69camaro 3 жыл бұрын

so you are using all 3 of your hands to hold the hinge and drive the pin out.. Did you notice you have a vise right next to you. but still a good video as always. keep up the good work.

@clabe1000 3 жыл бұрын

Lol I was thinking same thing

@miguelortega7799 2 жыл бұрын

Great videos question not related to this topic. On a 65 Mustang do the headlight buckets and rear quater extensions need a gasket to mate them to fenders and rear quaters?

@JoDaddysGarage 2 жыл бұрын

There is no gasket on the front that I remember. They had one in the back, but I don't use them.

@POLOreme Жыл бұрын

After pressing in the new pins on the lower hinges, when pivoting the hinge, before the hit the rollers, is it suppose to somewhat stiff with some resistance or loose? I did mine and the driver side came out loose when pivoting but has no play. And the passenger side has some resistance when pivoting the hinge

@JoDaddysGarage Жыл бұрын

There can be some resistance. As long as it's not binding, it should be fine. I would rather have slight resistance.