1993 Ford Explorer Clutch Replacement

Рет қаралды 24,307

7 жыл бұрын

I spent 3 days replacing everything clutch related in my truck, this is all part of my process of getting ready for my 1700 mile road trip to Kansas in a few weeks! Enjoy!

Пікірлер: 32

@samsala912 Жыл бұрын

This is a good video for repairing transmission.

@shawntowns8028 3 жыл бұрын

Gosh.... I really could have used a bit more footage on some of those pain in the ass portions. That's what I need to know how to overcome. Good vid though.

@PolecatCreekGarage 4 жыл бұрын

The slave cylinder went out on my 1991 ranger, also the throwout bearing has been sounding awful when depressing the clutch so i have been expecting this problem to come. Hopefully i can fix it in a weekend.

@fgallegos574 3 жыл бұрын

Oo9

@ayoal 4 жыл бұрын

Also worth noting the clutch will be completely out with it in first and will not even move, I've experienced clutches that go to the floor a bad pedal assembly ect, but never one that fully release s and slips so bad

@jerahmaya77 3 ай бұрын

fiddle around and find out ;)

@JoseRuiz-gw5ke 3 жыл бұрын

Hey brother, I have a 92 explorer 2wd, it shifts smoothly into every gear and the clutch engages the fly wheel fine but when pressing on the clutch pedal it makes a clanking and swooshing sound. And I have to depress the clutch carefully when switching gears or else it clanks. Have any idea what it could be? Thanks!

@TheShanegto 3 жыл бұрын

Jose Ruiz that’s a hard one haha, so I’d have someone under the car, take the little rubber plug out of the bellhousing so you can see the clutch engagement and then reproduce the noise and see if you can see anything

@RyanNelly 5 жыл бұрын

Oh crap. My 92 explorer.. Two wheel drive is getting there.. And I'm road tripping around the country. Wonder who to bring it to and how much it will run me

@TheShanegto 5 жыл бұрын

Ryan Nelson parts for me was about 300 bucks but it was about 2 days of labor so it would probably be fairly expensive

@pancakemix77 5 жыл бұрын

Hey man I was wondering if you could help me. I put a 18° camber on my 2004 Jetta M4 1.8T and I went over a speedbumb going 40 yesterday, and it felt like I hit a group of grannies playing ok it in the middle of the street. Now my car won't start and when I tried to do an oil check, I couldn't see any one my dip stick. Please help?

@TheShanegto 5 жыл бұрын

thanks josh please subscribe

@johnjames77 Жыл бұрын

I think you hit the oil pan and put a hole in it.

@ayoal 4 жыл бұрын

My clutch on my 1993 ranger 4.0 4x4 slips in every gear , it slips so bad it won't even move an inch in every gear even if you rev it high .it's the clutch? Slave cylinder? Flywheel? Any help u can advise me pleases

@TheShanegto 4 жыл бұрын

ayoal has to be the clutch. When your foot isn’t on the pedal there should be pressure applied. Pressing the pedal only releases that pressure. So the fact that it won’t move at all makes me think that. I’d look through the service hole on the transmission and have someone press and release the clutch and watch the clutch movement through the hole. I’d say the clutch needs to be replaced.

@TerryLooft Жыл бұрын

To change the clutch slave cylinder do I have to drop the transmission or can it just be moved back enough to get to the cylinder? I have a 4 post lift but not a transmission jack.

@TheShanegto Жыл бұрын

Transmission has to be fully removed unfortunately

@angelic420x5 Жыл бұрын

@@TheShanegto does the transfer case have to come out as well

@xavierperez2874 5 жыл бұрын

Excuse me bro, can you tell me what's the problem in my clutch because when I release it in 1st or 2nd gear, it makes an awful and loud sound .... Thank you

@TheShanegto 5 жыл бұрын

Xavier Perez that’s a tough one without actually being present. Generally if the noise only happens when the clutch is released (foot off the pedal) that usually means in my experience that it’s the throw out bearing. If it is only when In the gears 1 and 2 I’d suspect it’s a bearing within the transmission itself and is not clutch related. If you release the clutch in 3rd does it make the noise? How about reverse? If so it could just be the clutch pad itself.

@xavierperez2874 5 жыл бұрын

@@TheShanegto the noise presents sometimes, not always, but it feels like something is being rubbed, maybe if I can record the sound for you could you help me?... And in the reverse gear it doesnt make the sound..

@TheShanegto 5 жыл бұрын

Xavier Perez if you can send a video I’d be happy to take a look

@ernestoramirez6926 Жыл бұрын

Que bueno soy de el Salvador y tengo una camioneta igual pero el mecánico me perdió la manguera del clutch y quería saber la dimensión interna de la manguera para que me la fabriquen de ante mano gracias

@rubentapia1965 6 жыл бұрын

What is the model of that exchange box?

@TheShanegto 5 жыл бұрын

Rubeninti Tapia Arratia what do you mean?

@vascoiriondo6609 5 жыл бұрын

Why you change the fly wheel?

@TheShanegto 5 жыл бұрын

Vasco Iriondo a new flywheel is the same cost as resurfacing one so in my opinion it’s easier to just replace it.

@vascoiriondo6609 5 жыл бұрын

@@TheShanegto ohh ok thanks

@JohnDoe-gf6rj 4 жыл бұрын

Which model clutch did you get?

@TheShanegto 4 жыл бұрын

Jason Solstice all parts were from NAPA autoparts

@TheShanegto 4 жыл бұрын

I have had good results with Napa parts. I have 45,000 miles on the clutch now and recently had to pull the engine for a separate issue. The clutch looked in very good shape.