As somebody who both uses various brands of powered speakers in live sound applications, as well as fixing them when they break, I just wanted to mention that the lots of screws / lots of silicone glue thing is intended to prevent vibration damage when playing at full volume, as well as hopefully protect from the inevitable tumbles and rough handling that happen to musical equipment on the road. Also, on this particular speaker, the back plate is forming part of the speaker enclosure, so ideally it should not flex or leak air when the speaker is used a high volume levels. The only way to achieve that is with lots of screws, or by molding a sealed chamber in the back where the amp module can live in peace. Alto chose "lots of screws". I was surprised, and pleased to see that the amp module uses discreet MOSFETs on such an incredibly cheap powered speaker. Most manufacturers in this price range use the TDA8953 / 8954 amp on a chip, which is complete chintz in my opinion. And of course it should be obvious, but I'll say it anyway... there is no way on this earth, or in any other universe that this is a 2000 watt amp. Based in NDA service manuals for similar products, we might expect something in the 200 watt RMS range. It appears from your video that they use different MOSFETs on each channel, so perhaps 30-50 watts RMS on the compression driver, and around 150 watts on the woofer. Usually, manufacturers use the same amp board across the different sizes of speakers (10", 12" & 15") in a series, and they program the DSP to deliver the amount of power appropriate for the size of the woofer. If the series has a subwoofer in it, some companies will choose to use the same MOSFETs & inductors on both channels, then either use a dual voice coil driver in the sub, or design the amp so it can be put in bridge mono mode to feed a single voice coil sub - the old QSC KW family does the latter. The compression drivers are nearly always the exact same part across all sizes in the series. Good video sir, always fun to see what is inside other brands I've never had a chance to crack open.

Why at 76 years old do i find myself waching your vidios,Amswer you cheer me up!!! good luck.

U remind me of me grandad... He was a watch repairer. He would rather sometimes engineer a cog or a wheel for a grandfather clock than peddle his bike to buy one. The love and care he provided to the the item was only understandable to engineers like us alike. 😎👍

Apart from the amazing knowledge and skills , Mark is also a master camera man and video editor. He moves camera positions so often so we can see. What’s going on, no static overhead shots for this man! I dread to think how long the editing takes. Mrs Mark must be very forgiving 😂

Fixing that was like stroking a dog through a letterbox 😁 I finished work an hour ago to watch you do what I do. Smashing some overtime in 🤟 Thanks for posting Mark

What a likeable and pleasant guy!

Hey Mark, as a test and repair tech that used to work for Citronic, (when they had their factory in Melksham in Wiltshire), I am finding your videos very reminiscent of the time I spent fixing audio gear. I now work in IT, but keep my hand in as a DJ (another reason I worked ay Citronic). I have a pair of TS115A's which had intermittently dropped output to the bass speakers. Inspired by your video, I ventured to have a go at fixing these & and... success! I have never worked on Class D stuff before so I was quite wary of doing it. Time to fix one cabinet was about 2 hours especially after trying to remember how it all went back together again (used the other speaker as an aid memoir!). It was dry joint s galore. Lead free solder is pants! Thanks for the videos, it is quite cathartic watching someone else do all the work!

Watched a few of these now this guy is a genius 👏 keep up the great work ...

I'm picking up knowledge and understanding with every video you make and you're a good egg to boot so happy days👍🙂

I load tested one of those and it only made 245w rms. 2000w a bit of a dream. Spiked at 1805w at 1khz.

I feel the palette knife spreading of the heat sink compound is not only a good idea but a great tool for the job.

Mark thanks for bringing us along. Best wishes.

I HAVE A TS312 ....YOU CAN BE VERY USEFUL TO ME, AM ALWAYS POKING AROUND WITH DJ EQUIPMENT. ANOTHER GREAT REPAIR. YOU JUST EARNED ANOTHER SUBSCRIBER !!!

2000 Watts my ass :D - 200 Watts top. Great job, I like your smile, and enthusiasm, and yeah, looking at the crack around the tin soldering was suspicious at first sight.. Long ago I caught a tiny crack on the circuit line, noticed only with magnifying glass, and that was the source of the failure!

I always give big inductor legs a tug, on numerous occasions I've had them snap Within the board out of sight! thanks for a great clip, as always!

nice vid, Active Speaker top boxes can only play hi & mids with some mid bass and not bass below 60hz,this were a power sub box come in to play. i have seen alot of powered speakers being use in the wrong way it was made to be use.

Not to used out side of a Bedroom. Or this is what you will suffer every time. Great Video again Mark, Keep 'Em coming.

Great content radiocruncher recommended your channel and it been great.

OMG! This actually helped! Alto TS310 is actually Headrush frfr 112. Same company for sure. Thank you!

Amazing how lucky you are to have so many fixes to be a simple cold solder joint. I was rarely that lucky.

Hello mate Im John great videos marra love them keep up the good work

I work in a DJ shop on repairs, it's got to the point where we won't even take Alto stuff in for repair any more. Don't need the headache of fixing it, only for the customer to bring it back a month later with another fault! They're not a bad sounding speaker, just not very reliable it seems. And 2000 Watt? Nearer 200 than 2000 I'd say, don't know how these Chinese manufacturers get away with such bare-faced lies on their specs...

Hi Mark, everytime i see you get a shock in the titles it makes me laugh. I've repaired loads of speakers with the same issue. The last one was that the magnet came off of the bass driver, but the coil unbelievably was still intact. So i carefully bent the metal mounting lugs back into place then some strong resin to add extra strength, and yaaaay it worked. Keep up the great work m8. Paul😊

Gotta love an easy fix :) I bought a 1u power amp a couple months back, Its only fault was a blown main fuse... I originally assumed a short within the amp, to cause the blown fuse, But to this day, Running flawless on a new fuse... So must have been a power spike or something... Either way.... Loved an easy fix :D

Mark your the man....sooooooo clever!!

The beauty about Class D is that you can put a DSP into the control loop and correct the signals, you can also have your cross over directly in the digital domain.

I enjoyed. THanks. ! from Northern California ~

Love the smiley face well done !

Hola amigo estupendo tu canal me gusta mucho gracias por tu excelente trabajo 👍 me encantaría mucho si activases en todos tus vídeos los subtitulos en todos los idiomas el mio nativo es el español, y si en lo posible un día pudieras hacer unos vídeos explicativos muy detallados de tus equipos con los que reparas ,y algo más jjj de la serie de protección , y las cargas resistiva, con todo el esquema de construcción gracias y un fuerte abrazo

excellent video, thank you

I am guessing before you tore the Amp all apart you did check to see if the Speaker was Blown Right ? That would be mud in your face if you tore the amp all apart and it turned out to be a Blown speaker Huh ? That is why I teach my guys to ALWAYS check to see if the Driver on the horn or the Speaker is Blown first . Enjoy your Video's ..

That song you played is a banger

Thank you for posting 👍👍

Good that you fixed it. What surprised me is that you put all those screws back together before you tested it. Why? I would think for a low output test it should work without the cooling elements. And if there are another problem then you wouldn't have to do all the screws again.

ADORO SEUS VÍDEOS...VOCÊ MUITO INTELIGENTE..E DIVERTIDO...UM ÓTIMO PROFISSIONAL...GRATO..AMIGO....

You'd think they would cushion those pcbs better to prevent that kind of damage! BTW, when I have something like that where I know it's a common point of failure, I'll sometimes put some redundancy in it, like a bodge wire from the solder joint to a nearby trace, in case it fails again.

Nice one Mark

Proper job again, shame that we can already tell what will pop next on these - the chinesium caps!

Brilliant job - thanks

You are so funny! Thanks for your videos!!

Good job!

What a mess! Well done.

I'm just waiting for the day when a simple frequency sweep hits a YT content match. Satisfying that it was a relatively simple fix, though. Gosh, I'd get lost after the covers came off. I guess after you fix a few hundred things you learn what to look for.

What a horrible job to get in. This has put me off ever opening the 5 Kv2 EX10 active speakers I have, they'll be on thier way to you! You mention the voltage in the caps, for folk who don't know it would be an idea to explain and discharge safely.

Electronic specialist.youre great mend it mark

Love speakers like this "power consumption 800w" ....yet its somehow a 2kw speaker.

Hey Mark, nice repair, just a little info about the tongs you use to snip off the ends of the cable ties. I used to use the same Knipex ones till one day I had to do an installation and when cutting into a piece of plastic, one side of the tongs broke off and flew straight into my eye, have been on disability since with no sign of it ever improving. So just a heads up, beware of those tongs!

I've got a duff Dali E-12F subwoofer (known for problems with the amplifier board) so you've got me wondering now if it could be a problem with dry joints!

As you said, more work to get to the issue than fixing it. Such a simple issue as well.

Dont mind pal ...but you are looking like young Winston Churchill ❤😂😂😂

Love your channel, Mark. Whats the Blue material you are using for your work surface? I have a black Anti Static material, which was a nice idea, but heat sink compound makes a hell of a mess on the black. Ive got to change it for something that can be cleaned easier!!

Nice job Mark, reminds me of a car stereo I fixed for a friend with the exact same problem. Didn't have a lick of any kind of adhesive on it though. Your one was covered in it and still failed. Do you think it's down to thermal cycles in your case, that's a nice lump of copper!

Easy fix! Can't imagine these are anywhere near 2000Watts

Nice vid, love the skillful repairs. But this amp, what an aweful thing. Can't expect any decent sound out of it even if it works like intended.

Mark which soldering iron do you use ? great vids 👍👍

چقدر از خنده هات خوشم میاد 👍😍❤️😍😍👍👍👍😍😍😍😂😂

ill also teach you a small simple trick to get the amp panels off the speaker, i use a short XLR that goes between an input and out put, (its filled internally with hot glue or resin to act as a handle, and a firm tug gets them out

Sir your smile is so pretty love your video

Features Redesigned transducers for more efficient performance Class-D bi-amplification with 1,000 peak output 10" low-frequency driver with 2.5" high-temperature voice coil 1.4" high-frequency driver with neodymium magnet Compact, lightweight design for increased portability ($299.00)

Pop a PTC thermistor on the tweeter input. Would have to work out ac voltage near peek but it will heat up and increase resistance protecting tweeter driver from over powering.wont stop square waves though???

I have all Alto speakers, which have done me right for years. 2000w is peak, of course. But they are extremely loud, clean and efficient. The problem I'm having is not with my mains, but one of my TS212s subwoofers. I've have them for 6-7 years, so they've served me well, until one completely died. Won't power on. Tried replacing fuse, but no luck. Not sure it this would be a similar fix, or something else entirely. I'm no electrician. Wondering if this might fix the problem, or something else entirely.

You pull things apart by the plug NOT the cable.

Thousend Screws :) Good Work

Hi Mark, I tried to fix my AKAI Amp after it getting wet and it probably only had a minor fault but in the process I didn't recognize the drain of the transistors were connected to the metal heatsink on them. So it came like it had to and when taking out the board, I touched the heatsink with the metal thingy and it made a small smark between heatsink and transistor (seems like caps weren't drained). The power fuse ( 2.5A on the other side of the board) blew immediately. What do you think I should do? Is it possible that only the fuse blew or should I look for other faults on the board?

hello mark been watching your channel for quite a bit now you are very knowledgeable ...do you think that amplifier is 2000 watts ...true 2000 watts ???? ..i have yamaha dxr series powered speakers and dont go no where near 2000 watts ..alto ?

Hi Mark, do you mind telling me what soldering iron you use , mine is so crap , yours looks epic

For once, I think we could see the cracked solder joint better than you could. It was so clear it could have been magnified.

Hi Mark, Some 30 years ago I obtained a circuit to do a simple modfification to remotely control a Technics 1210 Mk2 turntable with three wires conected to the PCB and the audio mixer, unfortuneatly I have mislaied the info and it is no longer any referance to it on the internet, are you able to suggest a simple mod. I really enjoy your repair videos keep up the good work

Any chance you’ve had a look at any TS412/415’s? Can’t seem to find anybody doing a tear down or similar to see what the guts of it is like…

For information, can you please advise what make, model and tip style you use? 😁

I wonder why Mark did not put thread lock back on the amp chassis fixing screws, given his comments about the bass vibrating everything.

❤❤❤❤

师傅是英国的吗？技术真好。

I have same brand and the model is ts315.. ..but i have a problem of my tweeter is not working properly! its working but you can't heard louder!!

👍👍

My powered speaker turns on..but when i put the volume up..the music sounds scratchy and starts cutting out..also no sound coming out of ny subwoofer

Mark, at what temperature do you usually keep your soldering iron?

Skillz

Mark where can I buy cartridge cables inside the arm of SME309

whats the song at the begining? Sounds like a rendition of take me out to the ball game I want to know the name of that piece Super work on the skeaker too thanks was fun to see whats inside an alto speaker. I am getting one soon. was there polyfill inside?

Are the silicone pads under those devices not very good? You shouldn't need thermal compound AND silicone pads. Usually it's one or the other. The whole point of silicone pads is to eliminate the need for thermal compound.

According to 1:55 of your video, LED red wire is closer to the edge of the board. 😉

I only had the power switch fail on mine i have 2x ts112A top and 2xts112sub and a alto live 1604 PA desk :) i only use it for halloween and party.s

That speaker is NOWHERE near 2000 Watts of power output, what with absolutely no heatsink and fan, an idiot could work that one out.

Man, you're so happy... what you take?

what are you using for your signal gen?

How much do you charge for a repair like this?

If tandy was still open and sold speakers 🤣

I presume you shorted the capacitors off camera before you opened the power supply?

Where are u based ? I’ve a dsr 115 with protection light on . Been told need a new amp module but surely will be one component that needs sorting🤷🏻‍♂️any response will be really appreciated.

Coils can move on their own too!

When the clip red is on whats the problem? I News help with that problem

Hello How much"mV"you inject in the baffle with your frequenties generator? Tanks M from Belgium

0:44 Contour IN for a 🙂 Smiley Face If you know. Then you know. 😄

Has anyone ever got a schematic for an Alto product? I have a little ZMX122FX mixer that I'm sure just has a little power supply problem, but I can't even get a block diagram from them much less a schematic. They are very unhelpful.

I have a load of hifi stuff for repair, got any time spare?

Where are you based I've got a qtx 15a active speaker It works with low volume but as soon as i Turn it up, it sounds really distorted Being told it's the amplifier

Have you measured real power of the amps? I really dont believe that it has even 1000W in total. Maybe closer to 500W. But dont have such speaker so cannot do that.

are you in the uk sir?

😮😮😮😮😮