This is one of the best instructional videos on wheel bearings on youtube!
@alltsab4 жыл бұрын
Thanks
@michaelurukalo46573 жыл бұрын
You did a great job explaining the process of replacing wheel bearings
@gsmiklo8555 Жыл бұрын
Yes he did thanks so much bolt on bearings are cake im still practicing my press in methods
@luicarlos8822 жыл бұрын
this man the best video i have seen so far
@blow420 Жыл бұрын
Great video! The views were excellent and the instructions! Best one I've seen by far!
@alltsab Жыл бұрын
😊 thanks
@melvinmccoy983010 ай бұрын
Great job explaining how it was done.
@jwill98773 жыл бұрын
Overall nice work. I personally always use a torque wrench when it comes to bearings and hubs. And when I change one side I always do the other too because it's just a matter of time before that one goes. In my opinion when one goes they have reached the end of their life
@clintonschubert50912 жыл бұрын
Good explanation and really fast, just wished I had a press at home like you have in your shop.
@alltsab2 жыл бұрын
It cheap. You can buy one for under $200
@JRam757 Жыл бұрын
Thanks to the uploader for giving me the confidence to do this job myself. I had the misfortune of seized axles but I was able to push them out by hammering with the 30mm 12 pt nut 1/4 undone of the end of the threads to prevent the tip from mushrooming. It destroys the nut in the process but I was changing the entire knuckle which comes with a replacement 30mm (it was just easier in my situation). Didnt have access to a slide hammer otherwise I wouldve just used that
@alltsab Жыл бұрын
Good job buddy
@EJLily6862 жыл бұрын
thanks for the video. Let's me know what the mechanic will encounter on my car. Appreciate the volume of work to be done and I know at this time I won't be a DIY!.
@larryblatterman13 жыл бұрын
This is a really great instructional video!!! Thank you !!!
@alltsab3 жыл бұрын
You welcome
@lennylabastida99753 жыл бұрын
Great video and step by step instructions, thanks!
@alltsab3 жыл бұрын
You welcome buddy
@squeegeesquad19272 жыл бұрын
Thanks for the video, very helpful. You do need to replace both bearings at the same time as you would do it on your brakes, rotors etc...
@alltsab2 жыл бұрын
No you only do as need it Because bearing costly and sometimes it doesn't fail at the same time that is my opinion.
@justinmckibben45344 жыл бұрын
Did this today, you're awesome!
@alltsab4 жыл бұрын
Nice
@anshajansanshajans88073 жыл бұрын
Yes , good job.your video is pretty useful.
@dakotahogue4 жыл бұрын
You made this look so simple
@afrix8544 жыл бұрын
thank you Sir for this video..I have the same problem with my car (toyota corolla), noisy front wheel bearing (pax side) when running..I hope I can fix it, with your video as my guide..big big thanks Kabayan.. avid fan here from Northern Samar, Philippines..
@alltsab4 жыл бұрын
Thank you for watching don't forget to subscribe ok
@blitzreig92893 жыл бұрын
Great video man thanks
@thisoldgoat63962 жыл бұрын
Great video. I had the same noise from drivers side front. Not a diy job that I could do. My Corolla is a 2013 with about 75k miles .
@gabe6281 Жыл бұрын
I've got a 2013 with 250K miles on it.
@johnknope16642 жыл бұрын
Thanks for the video. I did it exactly how the video instructed me too. Except somehow it took 8 hours ! Lol. Nothing went as smoothly as it did in the video and at one point I thought I destroyed the new bearings. But I got it done and my car is fixed. Hopefully the wheel doesn't fall off on my road trip. Haha.
@alltsab2 жыл бұрын
Great job everything is practic and learn by mistake. I believe that your next bearing is piece a cake. I done many bearing job I still learning as well.
@madmag1458 Жыл бұрын
this tutorial saved me thank you🙏🏼
@alltsab Жыл бұрын
You welcome
@alvingatus49693 жыл бұрын
I learned a lot from you sir thanks a lot...
@alltsab3 жыл бұрын
U welcome
@jpal7542 жыл бұрын
Great video 🤙
@mikew61933 жыл бұрын
Great video. Just did this today, but I took a shortcut and purchased a complete hub that came with bearings installed (MOOG). Make sure you have a 12 point 30mm socket with 1/2 drive handy to take off the axle nut. A 6 sided one won't work.
@t1mech1ldtc603 жыл бұрын
Does that mean you totally skip the step of having to press the bearings in ?
@yvngkels12232 жыл бұрын
@@t1mech1ldtc60 yes
@505fastlife611 ай бұрын
Did you replace the bearing race on the hub?
@mikew619311 ай бұрын
No, the hub came with the bearing pre-installed. Super easy.@@505fastlife6
@fatbastardwithabeard10 ай бұрын
This is the best way for the average guy to do the repair. No press needed. Just remove and replace the entire spindle/knuckle assembly. Cost is a bit more but labor and frustration is less. Only downside is you may need to get an alignment after the repair. Why? Because the new knuckle could be a few mm off in the tie rod attachment area.
@Mlive7224 жыл бұрын
Great video
@fisherohvf-men6233 жыл бұрын
@7:17 would a tie rod end puller work better without risk of scarring the hub? ( I have to repair one of these on '12 corolla)
@This1LifeWeLive4 жыл бұрын
I think you are the first to show pressing in the bearing! My only beef is that there is a nut or something next to the tie rod nut that doesnt seem to have a hex head and I didnt see you remove it 😕
@whiteboy18973 жыл бұрын
Keep up the work my hmong brother
@alltsab3 жыл бұрын
You welcome
@newenglandendler5 жыл бұрын
i am doing a bearing this week i thought if you turn left then the bearing on the right makes noise if its bad , i am also going to use heat to remove the part thats known to stay on the hub . i am also going to put the new bearing in the freezer the night before . it makes it easier to install . thank you for the video
@bruceg18454 жыл бұрын
you're right - he said it backwards
@clintonschubert50912 жыл бұрын
At 307,578 miles I’m going to change both wheel bearings on my 2005 Toyota Corolla
@clintonschubert50912 жыл бұрын
Just to be on the safe side
@element2913 жыл бұрын
very good video. safety tip it was scary seeing your hand under that press when under pressure like you did at 9:10 never know what can happen with parts under pressure!
@alltsab3 жыл бұрын
There is no pressure just catching the drop of bearing only
@benhess35852 жыл бұрын
List of tools needed (minus everything bearing related) Impact wrench driver 30 mm socket has to have 12 points (non-hex) 22mm socket and 22mm back up wrench 21 mm 19mm impact swivel socket 17 mm impact swivel socket 15 mm socket 10mm wrench for ones with wheel sensor Needle nose pliers for Cotter pin, I had to drill and punch mine out from rust. On one of the nuts I had to use a propane torch to heat it up because the rust was so strong A few different hammers helped.
@rommeltolentino59543 жыл бұрын
Excellent job,anyway, Thank you very much.I hope you about to change the CV axle of toyota corolla .
@alltsab3 жыл бұрын
You welcome
@adrianolguin25533 жыл бұрын
for those who dont have a press would it just be easier to purchase a wheel hub/bearing/knuckle assembly all put together
@ingvar_primo8 ай бұрын
most brilliant way!!!!
@safetyalways77882 ай бұрын
Great car mechanic
@alltsab2 ай бұрын
Thanks
@oscarrmelchor4 жыл бұрын
Extra garbage just information. Great job on instructing and presenting.
@anthonyking43879 ай бұрын
How many miles! I noticed that you replaced both sides!
@GREENTICKETRO4 жыл бұрын
What socket size you are using to remove that nut from driveshaft?Thank's!
@alltsab4 жыл бұрын
Don't remember but I think 30mm
@kito1san5 жыл бұрын
does torqueing required on any of those bolts you install back?
@Carlitos2833 жыл бұрын
Yes, every single one of these bolts should have a specific torque.
@rickg8823 жыл бұрын
Thank you
@robertbolivarr83634 жыл бұрын
I have the same noise with my Toyota corolla 2017 when accelerating at 35 miles and up. And at the same time, it's making noise when you back up. Is it a bearing or Transmission? My car doesn't lose no power nor no engine lights on. Thank you All Tsab.
@alltsab4 жыл бұрын
Do a slow turn like the video to see it make noise increasing. If sound doesn't change mean that is not the bearing.
@qualifiedgabriel9130 Жыл бұрын
Nice one, but you didn't tell us the brand name of the bearing you loaded.??
@gyerekujsaggyerekujsag1853 жыл бұрын
Waohh!! It was really fast! Can you tell me the type of DeWalt that you used? It seems work really nice!
@alltsab3 жыл бұрын
I forgot the Dewalt model but if you search in Google or eBay it should have in there. The 1/2 drive with 700 ft lbs its really great one. I recently bought a Milwaukee one to replace the Dewalt but I'm not very happy with the Milwaukee. It said more torque but didn't and didn't run as smooth as Dewalt one. My opinion i recommend you the Dewalt brand.
@jacobkader26633 жыл бұрын
I don’t have a press. Should I just buy a whole replacement knuckle that has brand new everything... around 220 from rock auto for both sides. Both are going bad and I like to learn how to do this kinda stuff
@alltsab3 жыл бұрын
Yeah that is not a bad idea
@ynonser58042 жыл бұрын
thanks for the video and the explanation it really helped. what impcat wrench did you use?
@alltsab2 жыл бұрын
Dewalt and Milwaukee
@ynonser58042 жыл бұрын
@@alltsab which kind
@alltsab2 жыл бұрын
@@ynonser5804 the 700 ft lbs Dewalt and milwaukee one I think 800 ft lbs but I like Dewalt one better. It lighter and as powerful as milwaukee one.
@alltsab2 жыл бұрын
I don't remember the model number but if you search it only one in Dewalt that has 700 ft lbs.
@sol_2183 Жыл бұрын
My cv axle does not slip in as easily as yours does. I must be doing something wrong. Maybe I got the wrong hub bearing?
@alltsab Жыл бұрын
If rust sand the rust area. Some aftermarket part slightly bigger or smaller too
@byronlopez6787 Жыл бұрын
Great good👍🏽👍🏽👍🏽
@1221Ralph3 жыл бұрын
12:00 when pressing the hub in, is it going to stop where it wants to?
@alltsab3 жыл бұрын
Yes
@calibomber2094 жыл бұрын
is the press necessary to remove the bearing and intall? can you pound it out with a hammer and wood?
@alltsab4 жыл бұрын
Yes but it will take for a long time
@hazelsmith84794 жыл бұрын
If you dont have a press, you can get a bearing press kit
@charlielee33964 жыл бұрын
What happened to the ball bearings? I'm confused
@alltsab4 жыл бұрын
Bad
@lolwhodis78174 жыл бұрын
What is the part that you cut off with the machine??
@alltsab4 жыл бұрын
I think that part call Bearing race
@karenkoenig68013 жыл бұрын
What's the socket size for the 2 large bolts holding the hub assembly at the top?
@alltsab3 жыл бұрын
I don't remember but i think either 19mm or 17mm socket.
@SmokerBBQ2 жыл бұрын
@@alltsab 17mm
@ranger57053 жыл бұрын
Please tell me what you hit with hammer and screw driver at 13:42?
@alltsab3 жыл бұрын
That is to lock the axle nut to the axle shaft
@smtiic4 жыл бұрын
How much time is required for both wheels
@alltsab4 жыл бұрын
2 hours
@genericusername13653 жыл бұрын
Thanks.
@alltsab3 жыл бұрын
U welcome
@turdsandwicher3 жыл бұрын
Do you need to do an alignment afterwards?
@alltsab3 жыл бұрын
Yes if off no if everything set as default and running straight then no. I never have alignment on my work it run perfectly.
@richardmarsh13322 жыл бұрын
Whilst you would think the alignment would still hold in theory, in practice it doesn't . The reason is is the two bolts going through the suspension leg and hub casting are a very sloppy fit and unless you are lucky the alignment will be off for sure.
@zatan7913 жыл бұрын
When press the hub when do you stop
@alltsab3 жыл бұрын
Your press down until it soft stop
@msnod32 жыл бұрын
25 Dollars. Just purchased the same bearing here in New Zealand from Toyota. $187.50 thanks.
@alltsab2 жыл бұрын
Wow
@msnod32 жыл бұрын
That's the best price. One was $408!!
@alltsab2 жыл бұрын
@@msnod3 wow
@wRonG7652 жыл бұрын
I like hammer way too.
@vonniofdoom5590 Жыл бұрын
Some people turn into hulk after completing this
@zekejones69764 жыл бұрын
what is the purpose of your hammer at 13:45?
@alltsab4 жыл бұрын
Axle nut lock pin
@zekejones69764 жыл бұрын
@@alltsab what does that mean?
@kewln8ive4 жыл бұрын
@@zekejones6976 He was staking the axle nut to the axle shaft to prevent loosening.
@brinho1094 жыл бұрын
Where did you get the punch for knocking the old bearing out?
@alltsab4 жыл бұрын
Harbor Freight but you can buy from Amazon or eBay
@brinho1094 жыл бұрын
@@alltsab Ah ok, thanks for the quick reply. Is this part of a bearing race and driver set?
@alltsab4 жыл бұрын
@@brinho109 yes
@alltsab4 жыл бұрын
@@brinho109 please help subscribe to my channel ok I need your help
@foxmulder761611 ай бұрын
T think I'll just replace the whole knuckle with the new bearing and hub already installed..i don't have a grinder.
@alltsab11 ай бұрын
Good idea 💡
@luicarlos8822 жыл бұрын
unfortunally i dont have the presser to do the job the rest i can do it
@alltsab2 жыл бұрын
Take it to the machine shop they press for you
@malcolmjfaulkner79032 күн бұрын
Why not just replace the entire wheel hub assembly so you don’t have to cut the bearing out and press in a new one! They sell the complete wheel hub assembly
@naqibhamdan64554 жыл бұрын
Jack up the wheel..start engine put it in 3rd gear..so now you can feel which one is bad by touch and feel the vibrate at the spring..
@fisherohvf-men6233 жыл бұрын
@13:38 torque to 217 lbs/ft
@SilentServiceCode3 жыл бұрын
lol tell me you don't live in the rust belt without telling me you don't live in the rust belt. snap rings and knuckles and bolts just falling off the car like butter.
@alltsab3 жыл бұрын
I have work on some car came from the north region scared to touch it just fall off like you said. I don't know how those people work on car like that everyday. I probably will have nightmare every night. 😆 🤣 😂 😹
@donvandepeer77724 жыл бұрын
Looks like you don't torque anything. Especially the axle nut. Very dangerous