2003 CTS Traction control light - shifter lockup - C1295C code. LED brake lights need load resistor.
Пікірлер: 44
@Chillphill832 жыл бұрын
I just wanted to say thank you!!! You helped me so much with this!!! I had to tell my friend that sold me the car
@saskgrass2 жыл бұрын
Glad I could help! I’ve benefited from KZfaq videos many times. Glad I could pay it forward.
@ernestomytv4 ай бұрын
Cant believe a caddy got 250k miles wow
@saskgrass4 ай бұрын
That's kilometres.. it's 155,300 miles. :)
@McTyOnYouTube3 жыл бұрын
Do you only have to install 1 load resistor on the passenger side or did you put on 1 on the driver side too?
@saskgrass3 жыл бұрын
Just one did the trick. Working fine to this day!
@southerncross36385 ай бұрын
I have a 2005 srx, same problem, your radios the same as mine, goung to give it a try, Thanks.
@saskgrass5 ай бұрын
Hope it works! Good luck.
@cadillac91422 жыл бұрын
Traction control light on but I can drive my car and everything but my ac isn’t working now and it says service anti theft
@keithnoneya3 жыл бұрын
Great video, THUMBS UP! Only the resistor slows the current, as LEDS draw more current because they have less resistance. The computer senses this as a short not a blown light. Why it would set the traction, is probably something to do with how the circuit was designed in the computer by the electronic engineers. More than likely the LEDs are pulling down the voltage so low on the brake power feed circuit and the computer is setting a computer flag in the fault circuit as a break system open circuit, as there's not enough voltage to run the circuit. I do electronic Aircraft Test Set repairs for a living and I see this kind of stuff all the time. Good call on increasing the resistance on the circuit to fix the problem. Thanks for sharing. Best Wishes & Blessings. Keith Noneya
@saskgrass3 жыл бұрын
Keith I bow before your excellence!! Thanks for shedding light on the intricacies of why this happens. Knowing why it works is always better than just knowing it works.
@keithnoneya3 жыл бұрын
@@saskgrass Thanks David, no problem you seemed like the type of guy who would. I thought you did a super job on that video. I was looking for how to pull codes on a 2003 CTS. I think you would get more hits if you added, "& pull codes with the radio" at the end of the title, or did a separate video on just that. It seems there is no video named that on KZfaq. We sold the CTS when the rear end or transmission, not sure which, started making noise. Best Wishes & Blessings. Keith Noneya
@johnwolford27153 жыл бұрын
Please post more on this car I'm about to buy one ($500) that won't start and no lights come on with new battery and won't shift from park
@saskgrass3 жыл бұрын
@@johnwolford2715 Sorry John, I have not experienced that problem. Could be an ECM module or even the ignition key itself. (If the key was cut but not programmed the car won't start. Programming differs depending on the country the car was sold for. I had a new key cut but because I didn't have both original keys I needed a GM dealer to program it for me. In the US I believe you only need one original key to complete the programming).
@johnwolford27153 жыл бұрын
@@keithnoneya thanks so much!
@emiliorivera374 жыл бұрын
David wich colors wire you used to connect the resistor? White and wich other??? And where you get that? (the resistor)
@saskgrass4 жыл бұрын
On mine it was white and black.
@emiliorivera374 жыл бұрын
Thanks
@Polarcaine11 ай бұрын
One resistor makes sense because i yested one stock light and one led light and the issue was gone.
@mysikhlife5 жыл бұрын
David, which load resistor did you use? What are the specs? Thanks.
@saskgrass5 жыл бұрын
Be Spoke 50 watt 6ohm load resistor. They use them to stop hyper flash on led signal lights too.
@j.garcia646 Жыл бұрын
Mine start to give me this problems today but the only LEDs I have are the reverse lights and headlights,is this problem could be related to those LEDs too?
@j.garcia646 Жыл бұрын
Almost forgot mine has ABS,TC,and brake light on dashboard
@saskgrass Жыл бұрын
With mine I was able to fix the problem by adding the resistor to the tail lights. If you just added the LED headlights it might be the reason or part of. If your LED lights have been in for a while now and the traction control problem just shown up now the problem could be something else. With the brake light also on I would try to diagnose that issue first.
@ta7mourtv1213 жыл бұрын
Where. Clock temperature of this car
@saskgrass3 жыл бұрын
The 1st edition CTS came out in 2003. They had no temperature gauge. The year after they replaced the clock with a temp gauge. On the 2003 all you have is a warning light and a display that will tell you the engine is overheating on the radio screen.
@guttazonefpv52073 жыл бұрын
There’s a traction control button in the glove box maybe you can turn it off.
@saskgrass3 жыл бұрын
Good thinking.. but I don't think that would've worked since the error was caused by a low voltage signal from another system causing the traction control light to come on.. (which indicates the TC system is disengaged, same as pushing the button) and locking the shifter in place at the same time.
@smood_o24399 ай бұрын
Donut time
@jesusquijada86623 жыл бұрын
Traduselo en español
@MichiganMan19855 жыл бұрын
Moral of the story...don’t put ridiculous and silly aftermarket LED tail lights on ANY vehicle!
@saskgrass5 жыл бұрын
In this case I had no choice. I bought the car used and it already had LED lights in it.
@builderspluscustomhomesand21465 жыл бұрын
There's nothing wrong with LED lights and today's cars are led. Newer caddys are LED. It's not the LED lights, is the parts that people NEVER put on and/or the manufacturer's never include as part of their lighting setups. Even stock vehicles with LED lighting has the resistors in. That is actually a good looking stock-style kit and I like them. I have LED's in mine and the lighting kit included it. Never had an issue
@csimental03854 жыл бұрын
How do you make the stereo show the codes?
@saskgrass4 жыл бұрын
The station buttons 1 through 6.. push and hold buttons 1 and 6 till the screen lights up all pixels. you can use the right control knob to cycle through the codes and the clear button to cancel them.
@csimental03854 жыл бұрын
Is button 1 and 6 only pressed? It's not working for me, is there any other way to do it?
@saskgrass4 жыл бұрын
Carlos Simental that’s how it works on mine. 1 and 6 at same time. My CTS is Canadian. I know some aspects differ depending on its country origin.
@redsreelz75214 жыл бұрын
@@csimental0385 what year is your they stopped it in 05 or 06
@csimental03853 жыл бұрын
@@redsreelz7521 2005
@AcesK9AGA Жыл бұрын
Traced my wires and the main harness on the side of the engine by the AC compressor burnt out
@saskgrass Жыл бұрын
Good catch! With all the new electronics with vehicles it makes you wonder how many miles of extra wiring is in there..