2005 - 2015 Toyota Tacoma Front Door Speaker Install

Рет қаралды 56,976

Күн бұрын

Parts linked in the description below!
Watch a full tutorial as a 2015 Toyota Tacoma will have a new pair of NVX component speakers installed in the front doors. We will be using the NVX VSP65KIT 6.5" component speaker system amplifier which is rated for 125w RMS each side of power output for better sound quality.
Note: This vehicle wasn't equipped with JBL from the factory so we do not need to retrain a factory Bose amplifier.
This video applies to Toyota Tacoma models for years 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, and 2015. This video also includes door panel removal, crossover wiring, and installation.
Click here to see the rear speaker install on this Tacoma:
• 2005 - 2015 Toyota Tac...
Click here to see a small 8" sub install on this Tacoma:
• 2005 - 2015 Toyota Tac...
NVX 6.5" Component Speaker Unboxing and Demo video:
• NVX 6.5" Component Spe...
If you have any questions, leave a comment below! Be sure to like and subscribe!
Speaker Installation Parts Used (Amazon Associate Paid Links):
*NVX 6.5" Two-Way Component Speakers VSP65KIT: amzn.to/3qnxv13
--Recommended 6.5" Component Speakers: amzn.to/3vVgA73
--Recommended 6x9" Component Speakers: amzn.to/3kPlosO
*Metra 82-8147 Speaker Bracket Adapters (6x9 to 6.5"): amzn.to/3h9boYa
--If installing a 6x9" Speaker, you will need the Metra 82-8146: amzn.to/3hiOQnN
*Metra 72-8104 Speaker Wiring Harness (Pair): amzn.to/3xQDgqB
*2" Hole Tweeter Bracket Adapters: amzn.to/3gX571u
There are other sizes available (hole cutout includes flush mount cup diameter):
--Toyota Tweeter Bracket Adapter 1.25": amzn.to/3F7vT59
--Toyota Tweeter Bracket Adapter 1.5": amzn.to/2V9RS6w
--Toyota Tweeter Bracket Adapter 1.75": amzn.to/3D6LZKD
(Optional) - Toyota Tweeter Harness Adapter: amzn.to/3vS3wPN
Disclosure: As an Amazon Associate I earn from qualifying purchases

Пікірлер: 60

@nevamind7686 2 жыл бұрын

Awesome! But I’m really a slow learner I’ll probably have to watch your video 15 maybe 20times while I pause n play then rewind a thousand times lol. Hopefully I get it right.

@blazebott 2 жыл бұрын

nice video made my decision easier to snip the wires as i already purchased the metra adapter same as you did

@landonsugar2531 Жыл бұрын

thank you for the video! super helpful. I have a question for you. The resistor inside my crossover broke off, so there is not any signal being sent to the mid-range speaker. Can I replace the crossover with ANY crossover? Or does it need to be the same brand that I have now?

@luisgarcia4572 Жыл бұрын

Great video, this was done on the right door, when I do the left door do I need another crossover on the left door?

@markvegajcb Жыл бұрын

Thanks for the video. Those stock speakers are amazingly weak. My 1989 Hyundai had a better sound system. This is the best upgrade I've ever done on a car.

@El_Chompo 5 ай бұрын

Thanks for your vids. I'm exited. I'm getting those alpine components you recommended along with the metra adapters. Exited to have some high quality sound again. When I was a kid I had 6.5" Alpine type R speakers and they sounded sooooo good along with my subwoofers, unfortunately they went to the junkyard before I could get them out of my car and it's still one of my biggest regrets. Not only did they sound amazing, but the Type-Rs from 20 years ago looked super cool too, they were polished silver with the R in the center and a big fat rubber surround. The new ones have that cone which I guess improves the sound quality which is good, but it just doesn't look as cool and sleek as those old silver dish ones. The Alpine S-S65C are quite a bit cheaper than the type R spec, but I know they will still blow away the stock speakers in terms of sound quality. I wonder how different the S-S65C's really sound compared to the much more expensive type Rs?

@wilsq30 Жыл бұрын

Wish you showed when you cut the harnesses. Also do you have the part number for just the crossover?

@mikestivers8302 10 ай бұрын

thanks for the links. not many options for a 6x9 comp set, glad i searched for the adaptors. the entire head unit and factory wiring along with amp and all 7 speakers are going in the trash. that i can use almost any 6.5" mid is gonna open up the floodgates for my build options. update 12/5/23: i found a 3 way comp set that will fit perfectly, with a little trimming, that is.. be aware that some comps use a 2.5" midrange in their 3-way set. in this case, im going w/ Morel maximo ultra which is 6.5 midbass, 2.5" midrange, and 1" silk tweet. i found that it's possible to trim the "subaru/toyota tweeter adaptor" (around $11) to fit the 2.5" midrange. once this was done and that little mid was put in the metal bracket where the tweeter comes installed at factory, i was able to surface mount the tweet in the sail panel. this replaced a 2-way system using the CT sounds Meso set that I installed last month.. and omg it's a world of difference. soundstage was raised by a foot. now it sounds as if there is a live band playing on my dashboard! so my system i installed required a complete trashing of that JBL factory garbage, i used 3 way comps in front doors, 6.5 midrange in rear doors, 5 channel amp in back wall, 10" sub in truck box @ back wall, and a 10" android unit for the radio portion. the Joying brand comes w/ all harnesses to wire direct for '15 tacoma, and the factory back up cam also works! took prolly 15 hrs to do all doors and back wall w/ sound deadener and complete wiring, then another few hours to get the comps in the doors, with speaker rings, setting the gains and all that jazz. i see a lot of vids promoting a plug and play type set up, but friends.. if you have the time and resources do the entire system, you will not regret it!

@darkpharaoh666 2 жыл бұрын

I see you had no issues when closing the cover, how tall do you think is the max a speaker can be to fit in there?

@wafflemaine3953 8 ай бұрын

Do you have a video on how to replace the factory subwoofer ?

@youzabihh7763 Жыл бұрын

if i’m replacing the speakers do i also need to replace the tweeters ?

@joemay7704 5 күн бұрын

Great video! I don't see the link for removing the pins when retaining the factory plug?

@electricalron Жыл бұрын

Thanks

@bash7102 5 ай бұрын

Noticed that you added three different size mounting brackets for the tweeters. Which one did you use for the 25mm (1") tweeters in this kit?

@darrenbaillie98 6 ай бұрын

Hi i have a 07 extra cab tacoma with 6x9" mids & tweeters in the front doors i have a set of Rockford Fosgate T 1 series coaxial 6×9" speakers. I want to add tweeters and and amplifier to the system. Is this possible?

@joelmlutz Ай бұрын

Does the crossover absolutely have to be utilized if you have wiring harness adapters for both the tweeters and midrange speakers?

@GansterOzzy209 2 ай бұрын

I installed some new JBL speakers on my 2010 Tacoma, the two front ones work but the rear two keep cutting off. I checked to see if any wires were touching but nothing. Whenever I play music the music plays but then I just cuts off. Any suggestions.

@camokid8558 3 ай бұрын

Hey what size screws did you use for the 6 1/2s

@vancejones8244 8 күн бұрын

I want to replace the tweeter trim. I got it off, painted it and I cant get it back on

@brianwynn4968 2 жыл бұрын

the speaker adapter according to Amazon doesn't fit my 2015 Tacoma. is there any OTHER adapter that fits it?

@drakegriffin487 Жыл бұрын

i have a 2012 tacoma and this website called “crutch feild” says this exact mount the metra 82-8146 fits but for my jbl speakers it doesn’t need it. i would say check out that website it helps with everything you need and doesn’t sell you one thing but will tell you what to get for it all to work

@dougcrowe1226 2 жыл бұрын

Can i just install some 6.5 rounds and leave the crossover thats there

@ProvoBeastAudio 2 жыл бұрын

You mean leave the tweeter and just install a coaxial in the door? Sure, but you may be selling your self short with audio quality.

@cristovalmontoya5222 2 жыл бұрын

Can you just get rid of the factory wiresin door and run new wires from wires going to the radio.

@nastysoda9212 8 ай бұрын

much easier said than done

@6henny443 Жыл бұрын

So the radio speaker wire runs the cap and the tweeter and back to the woofer ?

@ProvoBeastAudio Жыл бұрын

Toyota runs the audio signal from the radio to the harness that the tweeter is plugged into, splits the signal there where one lead goes to the tweeter, and the other lead goes to the midrange speaker in the door. Both speakers are receiving full signal (no crossovers yet), but each speaker is individually crossover internally.

@6henny443 Жыл бұрын

@@ProvoBeastAudio OK you actually did explain that in the video so the four leads that are going into the Twitter harness two of those are for the in on the crossover and the others are for the woofer ? Then plug harness to new woofer and attach new tweeter to crossover ?

@Josedelgado001 Жыл бұрын

Can you install 6x9 instead of 6.5?

@Yogachara 7 ай бұрын

yes Metra makes adapters for 6x9 too

@bnyang84 2 ай бұрын

Isnt it be easier to replace it with a new 6x9 rather than a 6.5 speaker. Not only, dont 6x9 bump better than 6.5?

@wbrooks1234 Ай бұрын

Yeah they make a specific 6x9 adapter for the aftermarket magnet

@eghatch826 2 жыл бұрын

Are the crossovers needed ? What do they do, you have a video on crossovers? Lol

@Tomcoma2832 2 жыл бұрын

they change the radio output to the sound you hear. they are needed

@kodylemire2986 6 ай бұрын

Does anybody know why the speakers on the bottom of the door would go out but not the tweeters? Both of my bottom door speakers went out at the same time but the tweeters are still playing.

@ProvoBeastAudio 6 ай бұрын

Yes, they can fail at separate times.

@kodylemire2986 6 ай бұрын

@@ProvoBeastAudio yea I know they can because that’s what happened. But from what I’m reading it would be weird for both bottom door speakers to blow simultaneously right? So my question is does anybody know what would cause both bottom door speakers to stop playing at the same exact time? Is it the head unit or like a blown fuse?

@2011cubs Жыл бұрын

Does this work for the JBL system as well?

@ProvoBeastAudio Жыл бұрын

Technique, yes. However, the JBL audio system likes to see a 2 ohm speaker, where these speakers are 4 ohm (less sensitive, thus appearing quieter). I'd recommend replacing your JBL speakers with a 2 ohm speaker.

@2011cubs Жыл бұрын

@@ProvoBeastAudio last question. Do you know of a more powerful amplifier that is plug and play? Kinda like audison with BMW?

@hucarr5703 4 ай бұрын

One Question When do you have to up grade your speakers Wire ??? Thank you

@ProvoBeastAudio 4 ай бұрын

Nope, typical OEM wiring (in most circumstances) can support up to about 80-100watts RMS before there is a need to pull new, heavier gauge wiring into the door.

@hucarr5703 4 ай бұрын

Oh ok Thank you very much . I’m trying to up grade my system Tacoma 23 4 doors also need to buy the harness ready from you …

@ProvoBeastAudio 4 ай бұрын

Why are you watching this video then? We have a full install series on your gen truck. kzfaq.info/get/bejne/bLp_lZRnrq6ul5s.htmlfeature=shared @@hucarr5703

@hucarr5703 4 ай бұрын

@@ProvoBeastAudio omg Thank you . What harness do I have to buy from you if I planing to install an audio control amplifier?? Thank you

@brianhill3973 Жыл бұрын

With the crossover and speaker upgrade, are you still using the stock stereo?

@ProvoBeastAudio Жыл бұрын

Honestly we took this footage years ago, can’t remember sorry!

@_JEBUS 2 жыл бұрын

Is the install the same if the truck has the jbl system?

@ProvoBeastAudio 2 жыл бұрын

Yep, will work just the same.

@_JEBUS 2 жыл бұрын

@@ProvoBeastAudio quick question. If I use the adapter harness on the tweeters do I not have to use the crossovers that come with the nvx kit?

@ProvoBeastAudio 2 жыл бұрын

@@_JEBUS If your speaker requires a crossover, you must use it. If not, you risk blowing the speaker because you are sending frequencies to that speaker it cannot handle.

@andrewarciniega5436 Жыл бұрын

@@ProvoBeastAudio what about the part in your description where it says you need to retrain it?

@6henny443 Жыл бұрын

What did you do with the capacitor installed to the factory tweeter ? There are 2 speaker leads going into 4 attaching to a harness and then two going to cap and 2 going to tweeter. Should I retain the harness and just use one + and one - lead for the xover in and the others for the tweeter power.