2007-2014 Cadillac Escalade EXT Custom Platinum Dash Swap, Suede, Wood, Heated & Cooled Cup Holders

Рет қаралды 33,306

3 жыл бұрын

07-14 Cadillac Escalade EXT Platinum Dash Door Panel Swap, Suede, Wood, Heated & Cooled Cup Holders. Covers 2007 2008 2009 2010 2011 2012 2013 & 2014. The Escalade EXT was only available in Luxury and Premium. I wanted to do a Platinum interior swap so I changed the door panels, dash and trim.
►Support the Channel & Purchase WorkingWithWimberley Apparel!◄
teespring.com/stores/workingw...
As an Amazon Associate I earn from qualifying purchases
Craftsman Socket Set: amzn.to/37fwBZW
GoPro Hero 7 Black (What I Use to Record): amzn.to/2NCDCwf
► Subscribe: kzfaq.info...
► Website: www.workingwithwimberley.com
► Instagram: / workingwithwimberley
► Facebook: / workingwithwimberley
► Twitter: / wkwithwimberley
► KZfaq: / workingwithwimberley
This is a how-to video for the “Do-It-Yourselfer” working in the home, driveway or garage. No fancy or crazy expensive tools. I'll show you step by step how to get the job done!
*If the video was helpful, remember to give it a "thumbs up" and consider subscribing*
Music by @tru_inferno: truinferno.bandcamp.com
Disclaimer:
Due to factors beyond the control of Steven Wimberley & WorkingWithWimberley, I cannot guarantee against improper use or unauthorized modifications of this information. Steven Wimberley & WorkingWithWimberley assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. Steven Wimberley & WorkingWithWimberley recommends safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond the control of Steven Wimberley & WorkingWithWimberley, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not Steven Wimberley & WorkingWithWimberley.
2007-2014 Cadillac Escalade EXT Custom Platinum Dash Swap, Suede, Wood, Heated & Cooled Cup Holders #WorkingWithWimberley Episode 129

Пікірлер: 230

@greatgandalf5233 3 жыл бұрын

My 2008 lower dash Escalade 6.2 EXT has developed cracks on both sides of the Dash..Thanks for sharing the knowledge!

@WorkingWithWimberley 3 жыл бұрын

No problem!

@a.r.bigdog8957 2 жыл бұрын

New subscriber. Decided to keep my 07 EXT (had it since 09). Really glad I did after watching your channel 😀 Thanks brother. May GOD continue to bless you and us all 🙏

@WorkingWithWimberley 2 жыл бұрын

You’re welcome! I’m glad the video helped! And God bless you too!

@dominicsaad4103 Жыл бұрын

That car is a gem don’t ever sell it

@mrtennessee1o1 Жыл бұрын

Simply just too clean! Bravo! This walk through video was on point. I've used several of your EXT videos to work on my own.

@WorkingWithWimberley Жыл бұрын

Thank you! I definitely appreciate that! Glad it helped.

@daroachdoggjr188 2 жыл бұрын

This is brilliant, love your ambition and efforts

@DJKadilac 3 жыл бұрын

Looks good bro! The mistake I made was not allowing the adhesive to FULLY dry before trying to fit the material. I’m going to redo it in suede.

@WorkingWithWimberley 3 жыл бұрын

Thanks! Good luck!

@daroachdoggjr188 2 жыл бұрын

This looks really fresh, nicely done

@WorkingWithWimberley 2 жыл бұрын

Thanks! Much appreciated!

@akramalzain9730 3 жыл бұрын

Looking fire 🔥🔥🔥

@WorkingWithWimberley 3 жыл бұрын

Thank you! It was definitely worth it!

@vehcor 3 жыл бұрын

Looks good!

@WorkingWithWimberley 3 жыл бұрын

Thank you! The dealership that I traded it in to tacked on a lot more than I got for the trade in and it sold in less than a week. I guess I should be flattered.

@michaelschneider5190 3 жыл бұрын

Wow, came out great!!

@WorkingWithWimberley 3 жыл бұрын

Thank you!!

@ritawimberley544 3 жыл бұрын

It looks very luxurious 🥰

@WorkingWithWimberley 3 жыл бұрын

Thanks mom!!!

@omarzowila 2 ай бұрын

This makes the truck look like it was a Platinum from factory and Cadillac should’ve made a Platinum version of the EXT

@WorkingWithWimberley 2 ай бұрын

Yeah, that would’ve been cool.

@mndnmne 2 жыл бұрын

Looks really good!!!

@WorkingWithWimberley 2 жыл бұрын

Thanks!!!

@israela9631 3 жыл бұрын

Great work big bro 👊😎

@WorkingWithWimberley 3 жыл бұрын

Thanks! I’m glad it worked out. 👌🏽

@chuysprojectssilverado1642 3 жыл бұрын

Great video looking forward to swapping my interior to a platinum

@WorkingWithWimberley 3 жыл бұрын

Cool! The dash trim is the easy part. If you do the door panels, you’ll have to hunt for those Linen interior pieces.

@jayquezada3412 3 жыл бұрын

Came out sick bro

@WorkingWithWimberley 3 жыл бұрын

Thanks! It was tricky getting the suede on the dash, but it was worth it. 👌🏽

@jamesanderson4014 Жыл бұрын

Good job great video. Not a GM owner but highly appreciate your work. Going from a Concorde to install interior options from 2002 300m special which I stripped engine fuse block to tail light wiring. Need dash and upgraded BCM speakers and door panels installed. Programming will be the issue fitment flawless. You got a nice ride very well done.

@WorkingWithWimberley Жыл бұрын

Thank you so much! I hope your project goes well!

@E_-lb6df 3 жыл бұрын

Good video and nice Escalade

@WorkingWithWimberley 3 жыл бұрын

Thanks! Much appreciated!

@RonGau 3 жыл бұрын

looks awesome 👏🍁🙋‍♂️

@WorkingWithWimberley 3 жыл бұрын

Thanks! Much appreciated!

@Papadoodles 3 жыл бұрын

Great videos very informative

@WorkingWithWimberley 3 жыл бұрын

Thank you!

@chaelodoul9401 2 жыл бұрын

Dayum great work!!!!! Wish I could hire you to do mine.

@WorkingWithWimberley 2 жыл бұрын

Thanks! Much appreciated. It was definitely a labor of love.

@khalillong698 10 ай бұрын

Solid work brother

@WorkingWithWimberley 10 ай бұрын

Thank you!

@sonofogun8351 9 ай бұрын

Great job

@WorkingWithWimberley 9 ай бұрын

Thank you!

@djlonsiamdjlons9179 2 жыл бұрын

Looks good bro

@WorkingWithWimberley 2 жыл бұрын

Thanks!

@JOE_GOMEZ777 2 жыл бұрын

Great videos

@WorkingWithWimberley 2 жыл бұрын

Thanks!

@dylanb2142 2 жыл бұрын

excellent job!

@WorkingWithWimberley 2 жыл бұрын

Thanks!!!

@xxcloudxx6606 3 жыл бұрын

Love the coco/white linen.

@WorkingWithWimberley 3 жыл бұрын

Thanks!

@investinghutler5323 2 жыл бұрын

Awesome!!👏🏼👍👍✊🏼💪🏼💪🏼

@WorkingWithWimberley 2 жыл бұрын

Thanks! Much appreciated!

@raolito1980 3 жыл бұрын

Dang now you got me wanting to do Escalade interior in my gmc Sierra. Man hold up!

@WorkingWithWimberley 3 жыл бұрын

If you can find the parts, do it!!!!

@raolito1980 3 жыл бұрын

@@WorkingWithWimberley offer up has a dash but I would need panels for doors

@WorkingWithWimberley 3 жыл бұрын

@@raolito1980 I would check eBay. There seems to be a lot of door panels on there. Of course it’s going to be up to you as far as how much you’re willing to spend.

@shawnbraden6689 6 күн бұрын

Good work dude

@WorkingWithWimberley Күн бұрын

Thank you! Much appreciated!

@bjohns6279 2 жыл бұрын

Nice job. Very cool. I wish the EXT came as a platinum. Would make things a lot easier….

@WorkingWithWimberley 2 жыл бұрын

Thank you! Same here. Maybe we’ll see another EXT in the future.

@D.Magic_ 2 жыл бұрын

Very nice 👍🏿

@WorkingWithWimberley 2 жыл бұрын

Thanks!

@cmatta318 Жыл бұрын

Lookin good

@WorkingWithWimberley Жыл бұрын

Thank you!

@ElFinoJefe Жыл бұрын

Looks Supperr

@WorkingWithWimberley Жыл бұрын

Thank you!

@indevibe 3 жыл бұрын

Thank you very much for this tutorial.. The A pillars and forward Vents looks amazing.... We're they hard to get done... I like the way it look

@WorkingWithWimberley 3 жыл бұрын

The A-Pillars were easy, but the part under the windshield was a little tough because you have to cut around the vent.

@indevibe 3 жыл бұрын

@@WorkingWithWimberley oh ok, I see... Most of our trucks have VENT CRACKING ISSUES. I think this would mitigate that instead of cover all dash cover.... But the Interior looks clean.. I am going to take a stab at it......

@dirtykustomz 2 жыл бұрын

Sick

@WorkingWithWimberley 2 жыл бұрын

Thank you! Much appreciated!

@TRUCKOCD 7 ай бұрын

Was going to put the Platinum door panels in my Denali truck but decided not to bc the tan is lighter shade on them.

@WorkingWithWimberley 7 ай бұрын

I talk about that at 6:12. I had to get more pieces to match. Thankfully I was able to find them.

@bugsbunnygang7188 3 жыл бұрын

Send def go for the brown seats too, they nice

@WorkingWithWimberley 3 жыл бұрын

Yes, the brown seats are nice! Very hard to come by though. And they never made the brown seats for the EXT.

@Cleaning_Hero 10 ай бұрын

Wow! It looks awesome! Can you replace the steering wheel airbag cover with a leather-wrapped version?

@WorkingWithWimberley 10 ай бұрын

I don’t think Cadillac made a leather wrapped version of this particular air bag.

@keepitthoro6768 2 жыл бұрын

Nice work! Way better, now just match the headliner with the rest of the brown

@WorkingWithWimberley 2 жыл бұрын

Thanks! I don’t have this Escalade anymore. I drive a 2015 Escalade ESV now.

@HaulingStuff Жыл бұрын

I’m gonna bring you my truck… beautiful job..

@WorkingWithWimberley Жыл бұрын

Thank you! It was a lot of work, but not too bad. I think the toughest part would be tracking down all the platinum parts.

@eli2976 3 жыл бұрын

I see ya boi.. Niceee👌

@WorkingWithWimberley 3 жыл бұрын

Thank you!!! 👌🏽👍🏽

@TruInferno 3 жыл бұрын

Ayeeeeeee another project

@WorkingWithWimberley 3 жыл бұрын

Yes indeed! Keeping the Escalade fresh.

@TruInferno 3 жыл бұрын

@@WorkingWithWimberley this one makes me want to get a really cool whip so I can work on the interior like this

@WorkingWithWimberley 3 жыл бұрын

@@TruInferno You can customize the Malibu. I just saw a guy with 22” wheels on a Malibu just like yours.

@dadrut305 3 жыл бұрын

Nice work. I have a 09 platinum esv thinking of doing the A-pilers in a darker material like the coco brown seats. Where did you get your material ?

@WorkingWithWimberley 3 жыл бұрын

I purchased it from joann fabrics. It’s Stretch Faux Suede.

@sergiochavis223 2 жыл бұрын

Hey, I love the video. I have a 2009 base Escalade. I want to make my interior all black with the platinum seats. But where did you get the center console with the logo? I like that.

@WorkingWithWimberley 2 жыл бұрын

Thanks! I bought the console lid from Amazon and had it embroidered locally. Check out this video where I go over the process. kzfaq.info/get/bejne/q62VopCjtdnQdWw.html

@shotimemsu 3 жыл бұрын

fire

@WorkingWithWimberley 3 жыл бұрын

Much appreciated bro!! 🔥🔥🔥

@giohuncho Жыл бұрын

I have a 2007 Escalade and I was wondering if I could put platinum parts on it like the cluster since mine is different and stuff like the trims, door panels, radio and center console

@WorkingWithWimberley Жыл бұрын

I know you can do the trims, door panels and console. I’m not sure about the electronics like the cluster and radio. You’d have to do some research on those.

@ronisharobinson1735 2 жыл бұрын

Looking good! Do you think the 2015 escalade steering wheel would fit? Im thinking about doing it and did you just change the trim and door panels?

@WorkingWithWimberley 2 жыл бұрын

Thanks! I’m not sure about that steering wheel since it has different buttons and controls. I changed the door panels, door sills and some of the interior plastic trim. I disassembled parts of the dash and wrapped it with suede.

@Bluu1017 3 жыл бұрын

Great video!👍 I have a 2013 Escalade premium and I was wondering. Where do you order all your stuff for the Escalade?

@WorkingWithWimberley 3 жыл бұрын

I purchased to platinum dash from eBay. The door panels came from a junkyard I found on car-part.com and they shipped them to me. All the rest of the stuff like the knee bolster, glove box and door sills came from a local junkyard. It was the only time I’ve ever seen an Escalade platinum in a junkyard. It was my lucky day.

@DavidJones-pv5wn 3 жыл бұрын

Want to do this to my 2012 ext you have any links were to get parts or get started look so much better

@WorkingWithWimberley 3 жыл бұрын

I don’t have any links. Your best bet for the interior pieces is going to be eBay and if you’re lucky, a local junkyard. The suede was purchased from Joanne fabric.

@chuk0one47 2 жыл бұрын

I have the same Escalade 2014 esv but mines have premium package I got the cold heating cup holders that I want to install can you explain on how did you wire the cables to the cigarette lighter power

@WorkingWithWimberley 2 жыл бұрын

If your Escalade didn’t come with heated and cooled cup holders from the factory, the connector won’t be there. You have to wire it up yourself. To wire it up, I tapped the red power and black ground wires into the cigarette lighter. All the rest I combined and tapped into a fuse that only gets power when the key is in the run position. That was it.

@cliffhall4198 3 жыл бұрын

I have the same truck (just fitted with a 2019 front clip) and i was hoping you could tell me where you got the platinum center dash surround from??? i've been looking for about 3 weeks now with no luck.

@WorkingWithWimberley 3 жыл бұрын

I got it all from eBay. It’s really the only way. You’ll have to check pretty much daily to see if someone lists the parts.

@hillarykingart1983 3 жыл бұрын

What is the tool you are using to pry trim pieces off? Thank you

@WorkingWithWimberley 3 жыл бұрын

Nylon Pry Bar Kit: amzn.to/38iJRgu

@yunjang7548 Жыл бұрын

Wow! You are the Man! I have the Harley edition Ext. Would love to finish Harley ing it out. This is giving me some great ideas. Idk what they're called, but I want to Harley those 2 spines that come down the sides along the windshield interior where the speakers are. What would you suggest?

@WorkingWithWimberley Жыл бұрын

Thanks! 😂 I would probably say go with orange suede. That would pop with the Harley theme.

@yunjang7548 Жыл бұрын

@@WorkingWithWimberley Thanks. On a mission for Harley orange now.

@wezzil Жыл бұрын

Weird question but would you know how to hook up the platinum seat DVD players?

@WorkingWithWimberley Жыл бұрын

I don’t. If it’s separate from the rest of the entertainment system, you’d just need power. If it connects with the head unit, I don’t know how you’d do that.

@mrdeanv4414 3 жыл бұрын

Wow...looks amazing! What year corvette are you sitting in?

@WorkingWithWimberley 3 жыл бұрын

2002 Corvette Z06, 1995 Cadillac Fleetwood Brougham and 2015 Escalade ESV.

@jasonibis Жыл бұрын

hey where did you get the power for the heated cup holder, i dont see an extra jack in my truck

@WorkingWithWimberley Жыл бұрын

@dsten5947 3 жыл бұрын

Great vid! Can you show how to do that to a trailblazer in your next one?

@WorkingWithWimberley 3 жыл бұрын

😂 It’s the same process as what I did on the Escalade. If you’re feeling brave, we can definitely throw some suede in the TrailBlazer!

@shatteredaspirations746 Жыл бұрын

I wonder if those door panels would fit a 2013 Yukon XL.

@WorkingWithWimberley Жыл бұрын

They should fit. You just need to check the window switch trim. They changed them at some point on the front doors.

@DavidJones-pv5wn 3 жыл бұрын

How u get to fit the cup holder did you cut the air vent it don’t fit it’s to deep

@WorkingWithWimberley 3 жыл бұрын

I believe I heated the vent with a heat gun so that I could soften it. Then I pressed it in a bit to get the extra room for the cup holder. I didn’t cut it.

@MegaHowtoMan 6 ай бұрын

What adhesive did you use on the swede?

@WorkingWithWimberley 6 ай бұрын

I used 3M Super 77. amzn.to/3H45eWk

@edwardgarcia9170 2 жыл бұрын

Is it possible to go over how to fix sunroof when it won’t close

@WorkingWithWimberley 2 жыл бұрын

Unfortunately I don’t have the 2012 Escalade EXT anymore. I now drive a 2015 ESV.

@SIXONETHATSALL Жыл бұрын

Where did you purchsse the heated and cooled cupholders

@WorkingWithWimberley Жыл бұрын

I found them used on eBay.

@Papadoodles 3 жыл бұрын

Can you make a video on replacing the center consul with the heated and cool cupholders.

@WorkingWithWimberley 3 жыл бұрын

Unfortunately I can’t. The Escalade EXT is gone. But the wiring is simple. Tap the power and ground from the cigarette lighter. And the rest of the wires can all just go to a ignition only power source.

@ezradegreat Жыл бұрын

Great video! I just bought a 2007 escalade Esv. I got the cathedral tail lights for it. But I saw you had the heated and cooled cup holders. Where did you go to get that piece? Would really appreciate if you share that info. I looked everywhere and was not successful. Thx!

@WorkingWithWimberley Жыл бұрын

Thank you! I bought the cup holder from a junkyard that I found on car-part.com and they shipped it to me. Basically, you’d have to find one at a junkyard or eBay.

@ezradegreat Жыл бұрын

@@WorkingWithWimberley ok gotcha. Thx! I been searching every junk yard and no luck yet. Do they wore right in? Or did you have to do some extra work to make them functional?

@WorkingWithWimberley Жыл бұрын

@@ezradegreat If your Escalade didn’t come with heated and cooled cup holders from the factory, the connector won’t be there. You have to wire it up yourself. To wire it up, I tapped the red power and black ground wires into the cigarette lighter. All the rest I combined and tapped into a fuse that only gets power when the key is in the run position. That was it.

@alhamedi66 Жыл бұрын

Amazing beautiful project clean work. I plan to upgrade my 2007 ext to platinum but no used parts around me must order all from USA overseas shipping too much expensive. Can you put list by all parts diffrant between laxury and platinum. How much total cost Well done.

@WorkingWithWimberley Жыл бұрын

Thank you! I don’t have a list. I just bought parts as I could find them. I know it’s door panels, door sills, glove box, knee bolster, wood trim and b pillars. You should be able to find the part numbers on GMpartsdirect.com

@alhamedi66 Жыл бұрын

@@WorkingWithWimberley Thank you for your quick reply and interest and patience. Best regards,

@WorkingWithWimberley Жыл бұрын

@@alhamedi66 You’re welcome. No problem!

@DJ_BIGWOO 2 ай бұрын

? How did u wire up the cup holder is the plug already ran as a option??? Looks great bro

@WorkingWithWimberley 2 ай бұрын

Thank you! If your Escalade didn’t come with heated and cooled cup holders from the factory, the connector won’t be there. You have to wire it up yourself. To wire it up, I tapped the red power and black ground wires into the cigarette lighter. All the rest I combined and tapped into a fuse that only gets power when the key is in the run position. That was it.

@DJ_BIGWOO 2 ай бұрын

Thanks Bro

@WorkingWithWimberley 2 ай бұрын

@@DJ_BIGWOO No problem!

@mikeh1348 Жыл бұрын

Where did you get the heated and cool cup holders

@WorkingWithWimberley Жыл бұрын

I found them at a junkyard. I used car-part.com to find them. Your best bet is probably eBay though.

@ChevySS1968 Жыл бұрын

Hey man, nice vid! I've got a 2010 EXT that could use a little something. Can I ask how you got the knee-contacting console trim piece off? Are they just held in by clips?? My right knee firmly hits that trim piece (the piece you covered with brown suede), and I am gonna have an upholstery shop modify it for clearance. Thanks! Dave F.

@WorkingWithWimberley Жыл бұрын

On the bottom closer to the pedals there are a few bolts. On the top closer to the steering wheel, it’s clips. That’s it.

@ChevySS1968 Жыл бұрын

@@WorkingWithWimberley - thanks very much!!!

@WorkingWithWimberley Жыл бұрын

@@ChevySS1968 No problem!

@davidrossi8480 3 жыл бұрын

My 2008 Escalade windshield vent piece is cracked in the EXACT same place as yours. Wonder why that is. Any ideas?

@WorkingWithWimberley 3 жыл бұрын

It’s a known issue. It’s cheap plastic and becomes brittle being in the sun.

@sergiochavis223 2 жыл бұрын

Where did you order the platinum door panels? I can’t find a good set no where.

@WorkingWithWimberley 2 жыл бұрын

I found mine at car-part.com but I also saw quite a few on eBay.

@LiLrampage209 Жыл бұрын

Do you have a video showing how you wrapped the A-Pillars?

@WorkingWithWimberley Жыл бұрын

I show the process @ 3:45 and it’s the same for the A-Pillars. The only difference is I had to pull the existing fabric off the A-Pillars before I glued on the suede.

@LiLrampage209 Жыл бұрын

K thank you that’s what I was wondering because the fabric on mine is loose and ugly whoever had it before me tried to regule and the glue is showing thru 🤦‍♂️ but I really like how your looks with the suede 👍 thank you

@WorkingWithWimberley Жыл бұрын

@@LiLrampage209 No problem!

@AlanTrades 2 жыл бұрын

How did you wire up the heated/cooled cupholders? Do they actually keep the drinks hot or cold?

@WorkingWithWimberley 2 жыл бұрын

It did keep cans cold. I actually never used it for anything hot. If your Escalade didn’t come with heated and cooled cup holders from the factory, the connector won’t be there. You have to wire it up yourself. To wire it up, I tapped the red power and black ground wires into the cigarette lighter. All the rest I combined and tapped into a fuse that only gets power when the key is in the run position. That was it.

@AlanTrades 2 жыл бұрын

@@WorkingWithWimberley cool thanks! Do you remember which fuse you tap into? And what I'd the fuse tap you need. It's the fuse box on the driver side panel right? The one to the left of the steering wheel?

@WorkingWithWimberley 2 жыл бұрын

@@AlanTrades I don’t remember. But in this video, I tapped under the hood for a LED running light. kzfaq.info/get/bejne/b5xldZRor8q5eXk.html

@AlanTrades 2 жыл бұрын

@@WorkingWithWimberley if you could check your driver fuse panel and snap a photo or video that would be great. I need to tap a heated steering wheel as well.

@WorkingWithWimberley 2 жыл бұрын

@@AlanTrades Unfortunately I cannot. I traded in the 2012 EXT a year ago for a 2015 ESV which I currently have.

@jdm2877 2 жыл бұрын

WOW

@WorkingWithWimberley 2 жыл бұрын

Thanks!!!

@funguy7979 Жыл бұрын

I heard the avalanche and caddy ext dash has the same install points. Are they direct swaps?

@WorkingWithWimberley Жыл бұрын

I don’t know, but I’ve seen a few guys swap Escalade dashes into Silverados. I’d ask one of them. kzfaq.info/get/bejne/h6-JerSTvd_dqWw.html

@funguy7979 Жыл бұрын

@@WorkingWithWimberley thanks

@WorkingWithWimberley Жыл бұрын

@@funguy7979 You’re welcome.

@manbehindthecamera9898 2 жыл бұрын

Look good I’m doing something similar to mine

@WorkingWithWimberley 2 жыл бұрын

Thanks! It was a lot of work but I was really happy with the result.

@Bestbro2012 2 жыл бұрын

Hello, what did you use/how to wire up the cup holders?

@WorkingWithWimberley 2 жыл бұрын

I tapped into the power and ground on the cigarette lighter for the power wires. And all the rest, I combined and tapped into an accessory fuse in the fuse box so that it knows to only turn on when the key is in the on position. That was it.

@Bestbro2012 2 жыл бұрын

@@WorkingWithWimberley thanks!

@WorkingWithWimberley 2 жыл бұрын

@@Bestbro2012 You’re welcome!

@tyrannyterminator4179 2 жыл бұрын

How did you wire in the heated and cooled cup holders?

@WorkingWithWimberley 2 жыл бұрын

@tyrannyterminator4179 2 жыл бұрын

@@WorkingWithWimberley perfect! Thank you!!

@WorkingWithWimberley 2 жыл бұрын

@@tyrannyterminator4179 You’re welcome!

@glezrob Жыл бұрын

Great job and looks great Thanks for the info how getting wired

@Daniel4real20 3 жыл бұрын

Where did you get the door panels?

@WorkingWithWimberley 3 жыл бұрын

I found a salvage yard on car-part.com that had a set. There’s also a decent amount of them on eBay.

@AlanTrades 3 жыл бұрын

Wow where did you learn how to do all this

@WorkingWithWimberley 3 жыл бұрын

My father taught me. He’s the reason I started the KZfaq channel to share with others! 👍🏽👌🏽

@samariaclark3222 11 ай бұрын

If you still have the EXT, would you consider selling it? Very nice truck!!

@WorkingWithWimberley 11 ай бұрын

Thanks! The EXT is gone. I’m in a newer ESV now. kzfaq.info/get/bejne/r9ySmMqVnd2RdXk.html

@user-bv5os2ts2e 2 жыл бұрын

Where can I buy the same kit?

@WorkingWithWimberley 2 жыл бұрын

You have to try and find the pieces used. eBay is probably your best bet.

@dianecb1997 2 жыл бұрын

My car it’s a 2007 but has all the interior from a 2014 platinum edition but I have solo problems 🥺😭 the cup holder are not heating or cooling I disarm it and I didn’t find a plug for connect the heating and cooling. Pleaseeeeee do you know some one for do this cup holder work 🙏🏻🙏🏻🙏🏻 pleaseee

@WorkingWithWimberley 2 жыл бұрын

@dianecb1997 2 жыл бұрын

@@WorkingWithWimberley thanks so much I love your videos please do more like this one 🙏🏻😁 I’m an Escalade lover thanks for shearing

@dianecb1997 2 жыл бұрын

@@WorkingWithWimberley im sorry last question where can I buy the connectors that I need for this 🙏🏻. Thanks again for you help

@WorkingWithWimberley 2 жыл бұрын

@@dianecb1997 There is no connector you can buy. Your Escalade was not equipped to plug in the cup holder wires. You have to cut, splice and connect the wires yourself. This is custom work that requires you to have a decent understanding of wiring.

@8151noname 3 жыл бұрын

Hello Wimberley, Your truck looks great. Was the heated and cooled cup holder plug and play?

@WorkingWithWimberley 3 жыл бұрын

No it wasn’t. But it was pretty easy to do. I tapped into the power and ground on the cigarette lighter for the power wires. And all the rest, I combined and tapped into an accessory fuse in the fuse box so that it knows to only turn on when the key is in the on position. That was it.

@8151noname 3 жыл бұрын

@@WorkingWithWimberley Thanks, I think I'm going to have a heck of a time finding one of those.

@8151noname 3 жыл бұрын

According to the dealer I can still get the cup holder from them.

@WorkingWithWimberley 3 жыл бұрын

@@8151noname That’s good. How much? I usually see them go for $500 on eBay.

@8151noname 3 жыл бұрын

@@WorkingWithWimberley Hi, They said $470.00 before tax. That's Canadian, I'll verify that when I go to the parts counter.

@omarnino449 Жыл бұрын

Where did you buy the suede material from?

@WorkingWithWimberley Жыл бұрын

I got it from Joann Fabrics. You can find something similar on Amazon, just make sure it has a little stretch. It should contain spandex. Something like this: amzn.to/3D2IRiz

@omarnino449 Жыл бұрын

Ok thanks for your help

@WorkingWithWimberley Жыл бұрын

@@omarnino449 No problem!

@ikateulilo9058 3 жыл бұрын

No mods? Looks good!!!

@WorkingWithWimberley 3 жыл бұрын

Besides the interior, the only other thing I did was a Gibson dual exhaust. 👍🏽

@Jacblack69 3 жыл бұрын

I see you pimpin over there....is that a factory radio in there,and how did you put the cool and heated cup holders in?

@WorkingWithWimberley 3 жыл бұрын

Yes, it’s the factory radio. The cup holder is wired to get its power from the cigarette lighter. The cup holders aren’t bolted in. They just pop in and out with clips like the dash pieces.

@VITODABOSS1 3 жыл бұрын

@@WorkingWithWimberley I have a wire connection on the side of my cup holder. However, I can not find the connector to plug into it. Where is it?

@WorkingWithWimberley 3 жыл бұрын

@@VITODABOSS1 If your Escalade didn’t come with heated and cooled cup holders from the factory, the connector won’t be there. You have to wire it up yourself. If I remember it correctly I tapped the red power and black ground wires into the cigarette lighter. All the rest I combined and tapped into a fuse that only gets power when the key is in the run position.

@dianecb1997 2 жыл бұрын

@@VITODABOSS1 I have the same exact problem 🤦🏼‍♀️

@chrismadison8786 3 жыл бұрын

Good morning, Sir, How much did this complete job cost you???

@WorkingWithWimberley 3 жыл бұрын

The highest cost was the door panels. I think I paid like $600 total for all four. And the platinum dash and cup holders I paid like $300 total for that. The rest of the plastic interior panels I found cheaply at a local junkyard and all the suede was really inexpensive, it just took the effort to wrap the parts. And I did offset the cost by selling all the original parts that I replaced. That brought the cost down quite a bit. So if I had to guess, it probably cost me $300 to $400 total after selling all the old parts. It took a lot of effort though.

@royhickman4679 Жыл бұрын

🔥🔥🔥🔥🔥🔥👍🏾👍🏾

@WorkingWithWimberley Жыл бұрын

Thanks!!

@frankventimiglia5098 Жыл бұрын

i have same truck to a tee 2007 i just did mine with raptor radio

@WorkingWithWimberley Жыл бұрын

That’s awesome! The EXT is a great truck.

@chuk0one47 3 жыл бұрын

Nice ? You don’t have a video on how you made the cup holder work

@WorkingWithWimberley 3 жыл бұрын

Thanks. No I don’t have a video on that. It was trial and error. I eventually just tapped into the power of the lighter.

@teddybarboza6697 3 жыл бұрын

Looks amazing When you tap into the power the way you did does it allow for the buttons for the hot and cold to light up as well?

@liljune8209 3 жыл бұрын

How much did this run you

@WorkingWithWimberley 3 жыл бұрын

Probably around $900 total, but I sold the old parts on eBay and Facebook marketplace to offset the cost so it was actually less than that.

@raolito1980 Жыл бұрын

Easy swap since you already have an escalade

@WorkingWithWimberley Жыл бұрын

Ok thanks.

@realacerboy30 3 жыл бұрын

Second ✊🏿

@WorkingWithWimberley 3 жыл бұрын

Thanks bro! ✌🏽

@thegoodlifedrive 3 жыл бұрын

My dash broke in the same spot

@WorkingWithWimberley 3 жыл бұрын

I decided to repair mine and cover it. It turned out pretty well. kzfaq.info/get/bejne/orhorKljs8-4ioE.html