I called Mercedes to order a replacement handle, they told me they don't sell just the handle, I had to buy the door panel (which included the handle) for $1600; I hung up and ordered the handle for $22 bucks online and plan to replace it myself after watching this . . . . . . . That's nearly a $1600 savings . . . . . . . Thanks for posting this!

Thank you for this thorough video. You probably saved me over $500 instead of going to Mercedes.

Thank you for the video you just saved me 800 bucks from the dealership, they said some assembly needs to be replaced lol

Thank you for this! I got stopped trying to figure out how to remove that pin in the handle. You just set me back in motion!

Damn , my w204 door handle just broke. Seems like a lot of work. Thanks for the video.

Can’t believe I have to go this process 3 times… I have 3 door handles to replace

This is so much work to fix. I would mentally lose my mind lol

Great simple and straightforward video! Thank you for taking the time!

Thanks for the video saved me a lot of money didn’t save me much time tho. that’s okay I got it done thank you sir

Thank you for this information! This tutorial is so helpful! Wish us luck!

Thanks for the good tutorial! Here are a few things that I ran into that others may also find: 1. The upholstery padding on top of the door card (the part that tucks into the panel you're trying to remove) got plastic-welded to both long tabs. So I had to use a sharp edged tool to cut it free where it was stuck onto the connecting panel. Have to be careful not to peel the upholstery up and off the panel where it shows in the car. 2. The last white melted tit on top on the door latch side was too shallow to get a screw into, so I left it without a screw. Otherwise a screw would have punctured the upholstery on the other side of the door where you see it. 3. I used a 1/2" drill bit to cut the melted tits. I made sure it was sharp like new, and used very low rpm's like you did. 4. The door handle pin didn't extract like you said it should. So I had to use dikes to nip apart the handle down to the pin. I had 1/2 the pin showing full length. Then it still fought me to get it to pop out the back of the panel. 5. The customer purchased a metal handle (Made in CHIna), so hopefully it won't break again. 6. The new pin was too tight in the bore. So I had to tap it in with a backup piece so as not to damage the end of the pin. The end of the pin that didn't finish flush like the original one. It stuck out about 1/8". The handle pivot was a bit 'tight', but it worked good nonetheless. 7. The new cable keeper clip that was in the hold of handle wouldn't hold the cable in tight. So I replaced it with the original clip. 8. I removed the entire upper trim plastic. Made removing the door card much easier. 9. The BIGGEST improvement was I pilot drilled every hole to the bottom of each tit using a 1/16" drill bit. Otherwise, most of the screws would have wallowed-out the tit and been useless. Pilot drilling made all the screws go in good and tight. Again, thanks for the informative tutorial!

Thank you sir! Helped me change my power window switch out with a new one👌😁

MAN!!!!!! That's a lot of work ... should I do it myself or bring it to the dealer...... thank you for the vid 👏👏👏👏👏👏👏👏👏👏👏👏

Thank you sir, your directions were clear and easy to follow.

Thank you for the video, definitely helped a lot

Thank you for sharing something helpful.

Thanks, this helped a lot. greetings from Germany ✌️

Great job explaining.

You are awesome thanks for the tutorial, and the link to buy the parts. Look like it took you 3hr to complete?

My c300 handle just broke, wish me luck you all

Really appreciate this video!! My dad and I did it today but he broke the fragile plastic piece would that cause any problems??

another question, can we do this without removing all the wires and drill the panel? Why cannot we just replace the door directly after taking out the door panel?

Thank you , good info

Hello sir I need your help after fixing on the door the best I could my door would not lock or unlock. Please help.

Thank you, thank you, thank you!

My girlfriend's C250 has the same issue. Thanks!

Question - For a 2013 e350 - I needed to replace the rear passenger door. I was fortunate to find a replacement that matches except for the exterior door handle. The original door has the touch sensor, the replacement does not. Would the replacement door be wired for the touch sensor handle.

Does someone know what the white piece that goes into the handle to keep it together is called mine broke and the kit i got didn’t come with that piece

Door lock would not lock after I closed the door thin it locked

I have a 2012 mercedes c250 sedan and the door handle broke off on the driver's side. I ordered a replacement on Amazon with screws for $10 before tax. It seems fragile and plastic. I couldn't find a heavy-duty version.

Thank You!!!!

I accidentally drilled through the plastic so the screws won't catch. Can I wax it together? or use longer screws?

How long did that handle last. I got one from Amazon for a different car. Broke in less than a week.

Thanks

Man are you near Arkansas? I would gladly pay to have mine door handle fixed. My wife pulled on the handle one day and it broke.

A question, if I order a new indoor panel, do I need to go through this process?

Saved about 1,300 by watches this and other videos.

Would a 2010 model exterior skin door fit a 2013 model?

What’s the plastic thing connected to wires you said can easily break it broke😭😭

Did anyones car not start after fixing the door ? Mine says SRS malfunction and wouldn’t start. Please help!

I think it would cheaper to bring the car to you and you fix my car handle..... are you in or close to New York?

The plastic thing In the old door handle is now stuck is there a different way I can get it out or is it gone ??

It’s ok sir I got it now I got a little scared for a moment

What size is that drill bit you used

Wished you showed how you disconnect wire in 7:05

Poignée porte arrière gauche

My car shut down. Suggestions?

Lavoro ottimo ma da orologiaio. .non da meccanico.

This is why I buy BMWs. What a fucking joke