DIY to buy the repair kit copy and paste the link www.ebay.co.uk/itm/Bonnet-Rel...
Пікірлер: 124
@TheDeedsta3 жыл бұрын
Use some electrical tape around the flat head screw driver when prying off tabs/clips. So you dont damage paint on bumper.
@AidanD236 ай бұрын
Wish I'd seen this comment before I went ham on it 😂
@daltonhewitt-haynes86662 жыл бұрын
Dude. Your a life saver. I'm absolutely useless with cars and you simplified it enough for my simple brain!! Thanks a lot bud.
@declanmeaney2753 жыл бұрын
no need to break anything, once you get the grill off just grip the lock barrel and turn to the left then the right. the cable inside will do the work.
@vivk51353 жыл бұрын
My mum and I have never worked on cars before but this video was amazing, watched twice then took under half an hour start to finish!
@thesep19673 жыл бұрын
The guy who designed that is still wanted by Interpol ...
@zurcherzurich2133 жыл бұрын
;)
@russell62946 ай бұрын
ahahahaha @@zurcherzurich213
@lfitzfinch Жыл бұрын
This is absolutely spot on. It is a 10 min job with zero damage.
@GreyFox8843 жыл бұрын
I followed this guide and I now have a working bonnet lock. Thanks mate! 😄
@jdarny38772 жыл бұрын
You literally saved us hundreds at the garage! Thank you
@uberkelvin4 жыл бұрын
Successfully did it on my 2008 Focus! Pay close attention to where the creator inserts the screwdriver to pop the grille off - is quite difficult otherwise. Also be careful of where your fingers are when getting the lock itself out, I ended up pinching my finger between the bowden cable and the bottom of the grille. Smashing the white plastic bit off is quite a task, I ended up using the screwdriver as a sort of a chisel. The whole thing took me about an hour and a half, I also ended up damaging the paint on my bumper a bit, though I'm pretty sure many of you are more careful than I am - many thanks for making this video!
@TheDeedsta4 жыл бұрын
Yes I should have done it a better way of not damaging the the paint on the bumper. But you made good points👍
@uberkelvin4 жыл бұрын
@@TheDeedsta Cheers - again thank you so much for making this video, helped a lot!
@dubvibes7315 ай бұрын
Job done and back indoors within half hour , great video
@TheHiggins101 Жыл бұрын
Really appreciate you uploading the video it really helped when I could not get my bonnet to open. The steps were just what I needed. Thank you
@lamby6954 жыл бұрын
Well you helped me big time, installed a new part and works a treat! Thanks
@douglasvinter25573 жыл бұрын
Just popped bonnet now, what a great video well done,
@marksoden3 жыл бұрын
Thank you .your video is the easiest and quickest to follow
@chrismundy1604 Жыл бұрын
Brilliant! Thank you. Prising those press clips blind was only possible because you'd pointed it out. I wouldn't have tried pulling out the grill if you hadn't shown it. The rest was easy. THANK YOU!
@jamesprior94904 жыл бұрын
trusted what you said on the video and although i managed to break a piece off the plastic attached to the grill when pulling it out, it went perfectly with a replacement lock i bought for £20 on ebay. you saved me a ton of mmoney. cheers
@cintiaspataro32054 жыл бұрын
Can you please tell me what year is your Focus? Do I need many tools? Do you think I'll be able to do it?
@brianfearn42462 жыл бұрын
Great video. My 2010 bonnet has just given up this week. It dose tend to warn you as the mechanism becomes more difficult before it goes completely. I understand the mechanism was supposed to prevent would be thieves from opening the bonnet but this idea back fired on the proper owner 😳 I've ordered a new lach and cable. I've had my focus from 2011 and it's the first time this has happened.
@ash40342 жыл бұрын
Thanks this video maker . Really this video was helpful and we opened it so easy . Just who ever designed this did not have any clue of cars maybe fired from safe box company
@rich83rs3 жыл бұрын
If you are watching this ...also first watch another vid on YT from Chris Burton. He does it without hammering & breaking stuff and it only takes about 90mins. Try that first, but thanks also for this vid..all trying to help us.
@mcyates3 жыл бұрын
Thank you for this video, I was stuck at getting the gille off, didn't want to break the car, but watched your video and how you just yanked it out. I just went for it and it come out. Now I'm just ordering a new lock. These cars are rubbish lol!
@craigfishcake25434 жыл бұрын
Really good video. Thanks.
@andysmith859910 ай бұрын
Thanks very much for the video, managed to replace the lock successfully, thanks for you4 help cheers.
@pamelasoto69033 жыл бұрын
Thank you so much it worked! So easy to follow
@TheDeedsta3 жыл бұрын
You're welcome
@joe23.9 ай бұрын
Great demonstration , very helpful thanks 😊
@TheDeedsta9 ай бұрын
You're welcome!
@mikebircham76283 жыл бұрын
Really helpful, took a bit longer that video suggests
@dfwdanny4 жыл бұрын
Nice! Very detailed
@TheDeedsta4 жыл бұрын
Thank you very much.
@hearmenow9093 жыл бұрын
Legend. cheers.
@RECKLESSMELANCHOLY Жыл бұрын
thanks for the help!!
@jonescrusher14 жыл бұрын
Helped me out
@SilviaParraTruckingEU-NZ-AU Жыл бұрын
Thank you thank you thank you ❤
@tomennis74142 жыл бұрын
Thanks pal 👍
@8skellerns3 жыл бұрын
I rebuilt the lock in the new cable to match the old locks key when i did mine : )
@joppyjoppy77974 жыл бұрын
How long is the string? Thanks
@chamuzmchapa29742 жыл бұрын
Thank u...
@stephenm50004 жыл бұрын
If you don't want a 2 x key car. many Ebay kits sell a customiseable key tumbler you can build for your existing key. Also, I didn't half wince on watching you use bare metal screwdrivers against that nice shiny paintwork under the grill!
@TheDeedsta4 жыл бұрын
Yea i tried to be careful when i did it. Best if you put black electric tape on tip to prevent scratches.
@alirahmati78183 жыл бұрын
Tnx
@bosco99224 жыл бұрын
Top man great video 👍. I just bought the part and installed it there now was easy, saved me time and money much appreciated thank you🙏
@bradleyturner57503 жыл бұрын
Great video. Does anyone know the part number of the replacement lock? None of the eBay links work.....
@mayuranpanchacharam29713 жыл бұрын
Hi can u let me know what should I ask for in the car Orr shop for me to do the same
@PRE1543 жыл бұрын
Twist the wire (lock) left then right, after you get the grill out, should pop the hood.
@haticouponer29533 жыл бұрын
Tried this mine won’t pop
@sarajamil26722 жыл бұрын
ye u just need long pliers. will do the job, im reliably told by a mechanic.
@anamariachurchman61414 жыл бұрын
Neale H Hey I’m struggling with the hammering the plastic bit out. What did u do? Scared to break something. I see the vid jumps from old key unit to just cable and it’s out in no time
@TheDeedsta4 жыл бұрын
Yes because it took me a few minutes to break it. You just need to keep hitting it hard until it breaks.
@stuartyaxley53083 жыл бұрын
You can also swap the lock if you just want the original key all you have to do is punch out the two roll pins and swap the barrel I've done it .
@philip-w-brighton2 жыл бұрын
on mine there were 3 little pins
@bhorvath42083 жыл бұрын
Hi. The link no longer works. Would you have another link for this please? Thanks
@MrSmid8883 жыл бұрын
Arnold Clarke UK quoted me £600 to do this job today. I declined . She said it was £149 for the part and the remainder was for 2 hours labour
@rasher62903 ай бұрын
Push down on bonnet, turn key,ur welcome 🤗
@Locallybuiltauto4 жыл бұрын
That’s what ya get for owning a ford
@georgesearle74434 жыл бұрын
Hi what model is this focus ? I’m a zetec but don’t know if I have clips on the grille
@TheDeedsta4 жыл бұрын
I dont remember. I actually live in USA. Ill ask my cousin which trim it is and get back to you.
@djtyros19 күн бұрын
6:06 - I'd really like to know more about these two push clips. I'm currently researching to do this fix myself, and I'm unclear on how these clips or screws should be removed. Any advice greatly appreciated. thanks
@TheDeedsta18 күн бұрын
You can get a push clip removal tool or it's also called panel/trim removal tool. But I just used a flat head to pry it out.
@kevinhunter83934 жыл бұрын
Great help with mine, got the cable out of the housing but can't get the small cross piece out, any ideas, thanks.
@TheDeedsta4 жыл бұрын
That you yank out with a plier. ➕
@kevinhunter83934 жыл бұрын
@@TheDeedsta Tried won't come out at all.
@kevinhunter83934 жыл бұрын
By sheer luck put the screwdriver in to try and force it out and the bonnet opened! Have now removed it and your driver trick works a charm, really needed this because my battery was flat too, all well now, thank you very much.
@kevinhunter83934 жыл бұрын
By the way my car is a 2010 Focus and the grill removal is slightly different, held in different places, but still works, thanks.
@GreyFox8843 жыл бұрын
@@kevinhunter8393 I had the same issue, using a plier works but it took me a good 30 mins of yanking 😂 had to squeeze the clips at the end in so it could be pulled out.
@kirt1214 жыл бұрын
Brillant saved me money and time, gunna try this. have you got a link for the new part?
@TheDeedsta4 жыл бұрын
Link is In the description.
@kirt1214 жыл бұрын
@@TheDeedsta cheers man!
@kirt1214 жыл бұрын
@@TheDeedsta will that part fit my 2008 focus 1.6? Pretty sure your cars the same right?
@TheDeedsta4 жыл бұрын
@@kirt121 yep should work
@wendysides70813 ай бұрын
How do I open a ford escort 95 bonnet when I can't release mechanism ?
@antluvsbecky4 жыл бұрын
Hi I m currently having this problem could you please tell me which locking kit you got as my car is the same car but I've heard there is 2 different kits I dont want to purchase the wrong one thanks
@TheDeedsta4 жыл бұрын
Ive put the link to the one I bought in the description. Let me know if it doesnt work.
@antluvsbecky4 жыл бұрын
Linked worked. Brilliant stuff thanks 👍
@emergaa2 жыл бұрын
Hi bro, where did you buy that bonnet latch thatcomeswithkeys? I'm having problems as well with my ford focus cmax tdci. Thanks
@TheDeedsta2 жыл бұрын
There should be a link in the description.
@emergaa2 жыл бұрын
Thanks
@readyplayer2759 Жыл бұрын
What size is the replacement bonnet release mechanism?
@TheDeedsta Жыл бұрын
Im not sure what you mean by size.
@yesihavereadit3 жыл бұрын
It always rains when you are outside!
@zigmarskupriss71313 жыл бұрын
Good video but you only replaced the lock. What happened to the cable?
@TheDeedsta3 жыл бұрын
New lock doesnt use the cable.
@richardgosset45703 жыл бұрын
How much is a windscreen washer pump for a 2000 corsa 1.2
@richardgosset45703 жыл бұрын
Or even a recon
@jennasearle88772 жыл бұрын
I have a 2007 focus, has anyone tried this with that year? Not sure how much they differ, if at all?
@TheDeedsta2 жыл бұрын
I believe its the same
@MrTruth1114 жыл бұрын
damn they didnt fix the 8 year old problem...
@mr838114 жыл бұрын
Is this an estate car?
@salmansabarwal7484 жыл бұрын
will it work for ford focus 2009?
@Jonathan-L4 жыл бұрын
Yes, it's for 2004 to 2012.
@mohammedsaif91923 жыл бұрын
Im struggling to get the lock out any advice?
@TheDeedsta3 жыл бұрын
Breaking the plastic part?
@mohammedsaif91923 жыл бұрын
@@TheDeedsta no when taking the grill fully out the lock chamber is still there can’t seems to pry it out with force
@TheDeedsta3 жыл бұрын
@@mohammedsaif9192 maybe check with a camera if yours has any tabs behind it. Could be you need to twist it with the key then push it out. But I'm not sure. If yours is a different year maybe they changed it a little bit. Also try popping it out with a screw driver from the back by pushing against the cable
@The_Original_KL7 ай бұрын
Mine has gone, gonna have a go at it. Difficulty out of 10??
@TheDeedsta7 ай бұрын
4/10
@The_Original_KL5 ай бұрын
Finally got round to doing this. I'd say it was a little more difficult than a 4 🤣🤣 My grill deffo didn't come off as easy as yours in this video and I broke the cold air intake which I could glue and tape and put it back on and it's good. Hopefully I don't ever have to do that again. 💪💪💪
@yypyomastercar30374 жыл бұрын
Excuse me. Is this to same about Ford Mondeo?
@TheDeedsta4 жыл бұрын
Id imagine the repair would be same but parts would be different. But I dont know, not without seeing the car.
@yypyomastercar30374 жыл бұрын
@@TheDeedsta thank you.
@erosbifebeef51154 жыл бұрын
If I buy a replacement for a 2015 model, will it work for my 2006 ford focus model? It should be obvious but I found one that says it works for 2004 up to 2015 models. I dont want to buy it and it not work. Thanks!
@RandomClips27. Жыл бұрын
Done this but the new part only lasted 4 years which is really a crap design so have to do it again at least I know have to do it just needed a refresher 😁😁
@TheDeedsta Жыл бұрын
Maybe just do the flat head screw driver method?
@RandomClips27.4 ай бұрын
TheDeedsta just got a metal one from ebay it came from China so far its not broken
@jackbuff_I3 жыл бұрын
Brill
@christopherleishman99902 жыл бұрын
you spent more money than you should have and you can keep the original lock without breaking it swan neck 10mm spanner at the back you can access they 2 bolts from the front of the car just put your hands up and over and it only took me 40mins to undo the bolts remove the lock hatch replace that broken part and put it all back together
@OfficialMiles2Go2 жыл бұрын
How much does it cost for someone to do this for me. I need to fix an old car to sell it.
@davinatest84673 жыл бұрын
I don’t want to put another crappy locking system into this car......Cani just leave the bonnet without a lock?
@TheDeedsta3 жыл бұрын
Yes. Just use a flat head screw driver when you need to access it.
@cornwall92 жыл бұрын
Mine has broken twice now! Really poor design this. Probably gonna just use a long screwdriver instead of a key now once the 2nd broken latch is taken out.
@odyhira4 жыл бұрын
thanks for this i fuckin hate this design
@connectlogic Жыл бұрын
can you not just twist it with pliers rather than break it?
@sarajamil26722 жыл бұрын
this is the most annying but of having a focus. who designed it? why?!
@TheMcooper173 жыл бұрын
instead of hammer use vice grips and twist. but ideal fix/mod would be something like this kzfaq.info/get/bejne/jaqId8WIqLezaWw.html
@sarajamil26722 жыл бұрын
long pliers is all you need?
@TheMcooper172 жыл бұрын
@@sarajamil2672 if you have them. Mondeo mod works
@user-km4om8lh8q2 ай бұрын
This is a horrendous invention. Why not have another release inside the car. Unbelievable