2013 Jeep Grand Cherokee - Front Brakes

2013 Jeep Grand Cherokee - Front Brakes - D.I.Y. in the Drive Way

Рет қаралды 26,829

4 жыл бұрын

Yet another video of a disc brake repair.
Can it be done in the driveway with cheap tools? I think so, just be careful, and keep safety in mind. It's not worth to lose a limb or the life over a few hundred dollars savings.
In this example the front rotors of a 6 year old Jeep Grand Cherokee with 70000 miles on it.
Is this video better than the others? Well, it is.
Important to keep an eye on the slide pins (as explained in the video).
They make a tool to clean the slide pin bushing holes in the caliper called ball hone tool. You need 22mm for the front and 18mm for the rear caliper. I used the Dremel i use to grind the dogs nails, that worked pretty well...

Пікірлер: 23

@RockDog101 Жыл бұрын

Wish I would have seen this video before I beat the tar out of my front rotors getting them off the hub this past weekend.

@irvingguerrero7303 4 жыл бұрын

Excellent video. Well done. Thanks

@aviationmotivation4957 3 жыл бұрын

Thank you, awesome explanation!

@dextermorgan7732 4 жыл бұрын

😍 this is great. Thanks for posting!!!

@stephencannon3140 3 жыл бұрын

If the corrosion on the slide pins is surface rust, then you should be able to clean up with a piece of mild duty sand paper and clean. Don’t forget the slide pin grease when installing the pins whether you cleaned the pins or replaced

@sinergy100 2 жыл бұрын

Yeah it's an easy fix. I did a winter tire change recently and I always check the brakes. Those pins are easily cleaned using a metal file (or sandpaper) Grease them up after and reinstall!

@bpettit1978 8 ай бұрын

Thanks, super helpful

@williamjamesrapp7356 2 жыл бұрын

Good General Over View but if you ever do any other videos TRY and show close ups of DETAILS that the average person may not know that YOU take for granted Like in this video the exact way the CLIP SPRINGS and how they exactly go on ( SHOW CLOSE UP ) or what you do EXACTLY when bleeding the break lines after a caliper REPLACEMENT . A BETTER CLOSE UP of the break pads and which go where. You said something about it but I was not clear what you were talking about, BUT OVER ALL REALL GOOD JOB AND WE THANK YOU.

@alihsas 4 жыл бұрын

Thanks

@williealonso9973 Жыл бұрын

I did the same thing my steering wheel shakes when i brake when im going over 65mph? Help please?

@stephengarden1287 4 жыл бұрын

Best video of the proper way to do a brake job on this truck by far! Thanks! Would appreciate if you know torque spec for rear caliper slide bolt as well as I need to do this job very soon.

@mygiguser 4 жыл бұрын

on my car, the one there in the video the FRONT Caliper Slide Bolt Torque Spec is 55Nm (41Ft.Lbs.), and the REAR Caliper Slide Bolt Torque Spec is 27.5Nm (20Ft.Lbs.)

@stephencannon3140 3 жыл бұрын

While you have the caliper and the old brake pads off.....do yourself a favor. Use one of the old pads and press one side against the piston. Probably the inside pad but can be either. Press a C-Clamp between the rotor frame...(side with the Flex line hose.)... Makes compressing the piston so much easier and eliminates the risk of the C-Clamp from sliding off the piston and possibly puncturing one of the piston dust seals. For front brakes I have tried two ways and both work well. Method 1: Align the Clamp with one of the pistons....(doesn’t matter which one and slowly compress that piston. Loosen the Clamp and repeat the same step for the other piston. Option 2: Depending on the caliper design this may not be as easy. Center the Clamp in between the two pistons and slowly compress the piston. Same result as method one but may save a minute or two. You are not worried about the old pads if they get damaged....They are going to the same junk pile as a rotor without damage. For the Master Cylinder: loosen but DO NOT Remove the reservoir cap. This will make the piston retract easier by less resistance. Very simple reason for compressing the piston.......... Takes up the difference between the old pad and the hopefully thicker new pad. The Anti Sieze on the rotor hub is a good trick will make the rotor easier to remove for next brake inspection/replacement

@MethuselahMusic 3 жыл бұрын

Agreed. Key word: "proper". Great job!

@stephencannon3140 3 жыл бұрын

Bonus points for Bilstein Shocks!!!......sorrynforgot this was a brake video....😂😂

@fishycomics 4 жыл бұрын

bro please complete cmera.. wait I am on a car build Awesome work I still use the slider and molykyte them.. again great camera work

@mygiguser 4 жыл бұрын

fishycomics that was Osmo Action rocksteady on a little table tripod handle. Unlike GoPro all with one battery, and no fails during the recording. I planned on using the GPH as second camera, but guess what the battery was dead, drained over night.

@letsgo9459 2 жыл бұрын

I have a '12 Overland Summit with HD brakes. Is this the same braking system?

@mygiguser 2 жыл бұрын

yes, just different size

@Hoden123456 2 жыл бұрын

I am missing the o-rings that hold the brake discs. Where can I get new ones? Does anyone have a part number? Thx

@MoparGuy1625 2 жыл бұрын

You don’t need it. It’s used to hold the rotor in place for when the caliper goes back on. Just use a few lug nuts while you place the caliper back on. Does same thing.