I was certain I would be returning my bars for prewired. I watched this last night, slept on it, woke up this morning and did it exactly as he describes (down to the 12 ga stranded) and it worked in an hour. Thank you!

Thank you so very much for explaining how to connect the heated grips from right to left side. I’ve watched several videos but yours has helped me out the most.

This was the best video on bars i have seen nicely done thank you very detailed from stat to finish

Man you saved me so much 💰💵💰💵 I’m no mechanic by any stretch of the imagination but your DETAILED instruction has me looking good with 12 “ mayhem bars!!!!! You sir are the TRUTH!!!!!!

Thank you so much for this video! I just installed my bison baggers on my 2016 electraglide police model. I followed this video step by step. Only thing I didn't do is de-pin the wires. I ADVISE ANYONE WHO INSTALLS THESE BARS TO DE-PIN lol IT SUCKED pulling those wires through. Again,I'm so thankful for this video! Thank you KST Kustoms. I LOVE how my bars look and feel on my bike!

Just finished up my install with 14 inch Bison Baggers on my 2016 street glide special. Great video, it was like you were in the garage with me. THANK YOU for assisting me, you’re welcome in my garage any day!

Thank you for the detailed tutorial, I was able to install the bars because of it. It is much appreciated !

Thank y'all for the install video. Just added 10 in six bend kicker handlebars on my 2020 Electra Glide Standard. Huge difference. Great attention to detail in the video. Saved me some cash by doing it myself. Plus I learned how to work on my own bike. You guys rock.

Definitely the best video on bar swaps, especially the heated factory grips! Thanks

Amazing video. Due to fit mine tomorrow and this has helped a million times over. Glad I chose KST Kustoms!

That's the best install video I've seen so far, very detailed and easy to follow.

Thanks KST for your Bison bars and the video. Just finished installing the 12” on my 20 Electra Glide and they look great!

WOW!!! All I can say is THANK YOU for probably the most informative handle bar switch out (2017 Street Glide) available. You helped me save a lot of time & $$$. Thank You!!!

I litterly just finished putting 12s on my 16 ultra you were with me every step of the way . I can not say thank you enough for this video gave me the knowledge I needed to do this job right . Thank you so much

Thank you for posting this, saved me time and most importantly lots of money. Harley store told me I needed about $600 worth of extra parts to put bars with 2 more inches on my 2022 Electra Glide. Your video saved me that money.

Great video and great detail it's what we needed to do it our self! Thanks

Just used this video to install my 10” kst 6 bend bars on my 2020 streetglide special! Very informative video!! Thanks guys, keep up the great work!

Best how to video I've seen thanks! Just bought these bars for my baby

Hell yeah my man . I just saved over 500$ doing my bars . Thank you so much what a great video

The Bison bars are fantastic. Great video. Super helpful.

Thanks for the video! Looks so simple for you!

Awesome Job, and thank you for helping me decide which handlebars to install on my 19 Street Glide….

The customer service is next level with KST. The Harley dealer wanted 10 hours just to install the handlebars but instead using this awesome video and the amazing support from James at KST I was able to take off my stock bars then send them to KST. They did all the wiring including the install of new grips and set back a ready to mount set of Mayhem Bagger bars. Total time not even trying to go quickly was 3 hours and easy. KST rocks and thank you so much for all the help. The picture of my controls looks great on the website lol

thanks for your guidance on this install and nice meeting you at Bike week 2023. installed mine with no issues

Thank you KST Customs for this very detailed video. I installed your 10" Mayhem bars on my 2019 Elextra glide. I did have to order extentions for right and left controls. Job complete, now have an engine code, hoping to clear and not have to redo TBW again!

Great video thanks for the help. Followed step by step and got my bars done with no problem.

The perfect step by step walk through, helped me put install 14s on my 22 SG ST

Thank you very much. Best video on bars install by far.

Glad I found this video. I watched another notable big harley stuff channel, they took seat, gas tank, clutch and brake lines off and replaced the lines, for 10" apes.

Fantastic video Bret!! Sadly I wasn't able to have you do the install at Daytona, soooo I'm going to do it myself. Lots of great tips on the install. Thanks.

Awesome video and install and like most everyone has been saying great job on the step by step

Great video you made that look about as easy as it gets!! It don’t look like your first bar switch..

Excellent presentation👍🏼!!..and video quality. Thank you sir.👏🏼

Thanks I bought bagger bison bars was really easy to figure out

Great video! Now I have decided to do it myself and saving tons of $$$.

Damn, You did an amazing Job showing how to do this , wish you were close by to do mine. Thanks for the great video

Watched several times install was fairly easy, thanks for all the short cuts, Bison 12 inch bars look awesome on my 21 SGS

Very nice Instructions for Handle Bar Install I will give you Five Stars Brother, Thank You.

Great video and my hats off to KST for a great install today. I was amazed how quickly the job was completed. Only a group of professionals like KST could have pulled this off. A special thanks to Sid for getting me in the house and keeping Gods word the highest of priorities. For those of you looking to get out of the factory bar business, why look any further than KST for your upgrade needs. Don’t waste your time! Let KST hook you up!!! Thanks again..

Great video! Just installed the Mayhem Bagger 12” bars today on my 2017 SGS. Took about 4 hours. Everything was pretty smooth and easy with the exception of getting the wires through the bar. As others have said the welds inside the bar are very rough and the wires get caught. Definitely expanded my vocabulary working those wires through. 12 gauge copper wire and a little grease is essential! I was definitely intimidated by this project and almost coughed up the cash to have the dealer do it but this video gave me the confidence to do it myself and I am glad it worked out. Love the look and feel of the bars. Should have done this years ago. Thank you!!!

Nicely done!

Great Video Matt

My bars will be here tomorrow! cant wait to get them on. Gotta make myself a pulling tool.

I tip my hat to ya . Dam Informative video you’re the man excellent keep them coming .

Thanks for the tips on these new bikes....missed the red wire for grips.... 5 mins here and all set..👍👍👍👍

Thanks for the video, will be attempting this weekend.

Now those are instructions thank you sir an it was too very easy

Wanted to also add my thanks. I was struggling to run the 2 wire bundles down and inside the HD Fat Chizeled ape bars. I left it for the day and started doing some research and came across this video. Your explanation of how to get both those wires through did the trick. Much appreciated. Thanks again

THANK YOU for your tips man.

Great video!! I just installed the 10" Mayhem Bagger bars on my 2020 Ultra Limited 3 weeks ago and this video would have been helpful. I struggled with the wires through the bars but I didn't de-pin any of the plugs or remove the OEM harness cover from the throttle side. I am sure doing that would have helped run the wires through.

Great way on feeding two wires through the bars

Great presentation, I'm going with 12" bars on my 2019 SGS from fat baggers(ez install) lotsa good tips, I'll use your video as my go to for sure...... thanks Marty, from Michigan

Best install video. Fought with the wiring a little bit but other than that follow the video and youll have no problems !!! 🤘🏽

Thank you for the help!!

The most detailed video on you tube. I mean step by step!

Hi, I really wanted to take a minute to write, and say “Thanks” for your video! After watching it, I decided that I would be able to tackle it, and placed an order for the 12” 6 Bend Kicker Bars, along with the Wire Extension Harness. Take care, Eddie Hugs Philadelphia, Pa.

Watched this video while installing 10” six bend kickers on my 22 street glide. Some very different procedures for the cable clutch. No way 12” would have worked with stock clutch cable. It might be a good idea to make an updated video. Took me about 3 hours start to finish. Thanks for the great video and awesome bars.

Thanks for the video, very helpful

Thanks to this video I was able to install my 12" by myself.. took me 5.5 hours though 🤦🏽‍♂️

Nicely done

Installed Bison bars onto my 21 Streetglide using this video…It was super doable and the results are amazing! A couple of things I did for those interested. I used weed eater string and I didn’t de-pin any connectors…. I plumbed both bar ends and switch slots first. Duct taped the wires, connectors, weed eater string and applied a light coat of Vaseline and pulled both the bar end and switch slot electrical wiring simultaneously ensuring I offset the connectors per entry point so I didn’t have a tie finish around the bends etc…. Pretty smooth for what I thought was going to be a tough install.

This guy gives super instructions did some 10 inch la choppers twin peaks 1.5 on my 2016 limited low thank you sir but I hate my 10s I want 12 or 14s 10s too damm short

best tech. video I have seen thanks

Excellent!!!!! Thank You.

Love your vids, but wish it was in hd. I've changed bars on my 08 Ultra twice. Biggest job is taking the wire ends out of the plugs to do internal wiring. I found if you lub up the harness with Vaseline or similar, they slide through the bars easier.

thanks. i just used this video step by step.

good show thanks

I just noticed the man cave sign in the corner at the end of the video. I have one just like that. Purchased at Old Time Pottery in Foley, Alabama while on vacation down there

Going to give it a shot… rolling 🎲

Great video, would love to put some custom bars on my street gilde. Was thinking to have my local harleydavsion dealer do the install. Depending on cost . Also concerned about warranty if I do it myself.

Fantastic video. I successfully installed 10” bars on my ultra. I’m so glad I didn’t give Harley $500 to install them. Thank you so much!!! Great job!!

Thank you

dan nicosia ..its fixed . when I did this ... our friend didn't say disconnect the battery ..hmmm its ok my fault .I did not disconnect the battery and it was crazy fearful ..nothing worked but the radio and head lights were on and i had no control over anything .. and it wont start ..no worries your 5 amp fuse blew ..replace and rejoice ..everything is fine now ..go ride ..

Very nice, thank you. If the new handlebars had rounded corners would I need to take the switch connectors apart?

I never depinned the connectors, I would tape with electrical tape and throw a little grease on the end of it and rub down the tape. All of my connectors came through easy

great video!!!! helped greatly with my 10” Mayhem install. Thanks!

I completely agree with every commenter before me, this vid and others gave me the confidence to do my own bars and save from going to the local HD shop, going to order my Bison bars from you, but for a 2023 RGS, do I need to get that Krazy Klamp you guys sell, if I get the torque per pound right and also would you recommend changing out bushings....every video I have watched someone is doing something different, so just wanted your opinion.

Hey man excellent video! Gonna order some KST 16’s today. Can I run a 16” with using cable extensions only on 14 street glide?

Bought 14 straight jackets from you guys that say they are for a 07 road king cvo with hydraulic clutch, but the 1 1/4 bar interferes with both brake and clutch resivors.

What would be different on 2013 street glide install? Thank you for all your help

Great job there! Question 🙋🏻‍♂️. I’m going for 14inch factory 47 assault handlebars on my 2021 StreetGlide Special. Do you think it will block the stock mirrors? I’m 6.1 ft if that helps

Hey I bought the mayhem 12 bars for my 16 street glide and when I try to attach my switch housing that have the run switch on it won’t snap in place

You guys should post this video for road kings since we don’t have to take off the front fairing . Would really help

Just did Patriot bars on my 23' SG special and found out I had to modify the inner fairing when using aluminum risers as well as the lower plate by the ignition switch below the inner fairing. It did not want to seat correctly without doing that.

Yeah my 14 bars are just 👌 think I'll give this a miss 🤔😉😎

In the process of finishing up 12inch bagger nation but I’m having problems with fitment on the clutch and front brake lines any suggestions @KST Kustoms

This was an absolutely fantastic video. I just watched as I went through it on my own the only issue I have now is that when I start the bike up, I hear a weird clicking noise when the ignition is on, and it won't start. It'll just keep turning over until I give it some throttle, and then when I do it pretty much red lines. Any thoughts? It's killing me

Do you have to extend the wires on a 2016 SG for 10 inch bars

I’m getting my bars installed at HD.. I don’t have heated grips but I might want em later on... what do you suggest I do?

Installed my bars tonight and have no power to my right controls. Triple checked all plugs and pins and they are all good. Everything is connected and I'm throwing a bunch of codes. Any tips or help would be greatly appreciated.

Any videos for older harley glides 90s-2008

I noticed you relocated the stock mirrors. How did you do that?

Will you make these for the 2021 Street glide?? I been looking for new bars I love yours but I don't think they work on the 2021 models

Are new Poly bushings needed / suggested with a new Electra Glide Standard and these 12" Mayhems?

Do you do these bars in stock height with less pull back?

How high can the bars be before you have to change the brake and clutch cable?

Brett

Do I need the wire extensions when in installing khrome Werks 300519 bars? They are two inches taller and 2 inches further back. Tks

fantastic video watched again and again . Ive done the job I have a question if you don't mind. 1. the red/black power you plugged in when reconnecting the heated grip side (close to the fork) was the power connector there as standard or did you install it?. I cant seem to find it . I guess there is a back to closing everything up too ....phew . many thanks Andy

Do you have to remove the gas tank and move the ABS line for the 14-inch bars? Thank you