This vehicle is an auction vehicle. owner replaced the PCM with a re-manufactured pre-programmed one from Ebay. No crank no start status and No communication with PCM.
Пікірлер: 53
@adrianchavez47492 жыл бұрын
I had the same engine failure, hill assist and starting system fault. Thanks to your video i checked the 10 amp fuse, sure enough it was blown. Replaced it and car started up!!! Thank you!!!
@DallasAutoDiag2 жыл бұрын
Glad that it helped :)
@cccEngineer3 жыл бұрын
Long story short fuse #36 in engine compartment replaced and the engine started.
@8power02 жыл бұрын
COMPLETE DIAGNOSTIC, GOOD JOB !!!!!!!!!!!!
@SucksTeamMx2 жыл бұрын
PATS should be relearn after swap the PCM from Ebay, that system can't be plug and play, the key won't let start the engine till pair the PATS. Thanks for the info!
@DallasAutoDiag2 жыл бұрын
Thanks for the tip. I did not know that at that time.
@SergioHernandez-ir2wk Жыл бұрын
What does PATS stand for?
@SucksTeamMx Жыл бұрын
@@SergioHernandez-ir2wk Passive Anti-Theft Systems
@nicolasmarcano24122 жыл бұрын
I had the same issue. I replace the same fuse and the car started. I let the car without turn it on for 3 days and then it never start again. I checked the same fuse and I was blown. I replaced it and it didn’t turn on and now I don’t now what it can be
@sweetjordan48683 жыл бұрын
nice video thx
@robertchiarizia9463 Жыл бұрын
Have a 2015 Focus SE 2.0L Hit a deer on driver side in front. Dash glitches. Sacs we intermittently says key is not in on position. Checked relay and fuses. PATS could be an issue. No PCM changed yet. Want to check PCM but under car to get to. Wonder if I have to go that far. Also to check for 12 volts at starter difficult to get to. Any easier way than removing intake manifold to get to it?
@DallasAutoDiag Жыл бұрын
I think you can get to it by removing the driver side wheel and then the fender liner. I suspect wiring damaged or maybe pcm harness disconnected.
@robertchiarizia9463 Жыл бұрын
@@DallasAutoDiag thanks, will disconnect and reconnect the harness to pcm after inspecting condition. Thankyou for confirming how to get to it.
@richardmarkham83693 жыл бұрын
I have an 09 Focus 1.6 TDCI with similar fault. No crank. PATS is showing error 1:6. Dash is displaying DTC U2510. Forscan won't connect. Checked canbus at OBD. 60 ohms. Good signals on a scope. Good continuity between OBD and PCM. Power and grounds all good at PCM. Checked fuses and battery. +12 from ignition gets to PCM and ECU relay is operating. If I power up PCM on a bench it draws 200-300mA but Forscan won;t connect. Checked solering on dash pcb connector. Found some cracks, resoldered but made no difference. Is PCM dead? Will PATS stop Forscan connecting to PCM? Anything else I could check?
@DallasAutoDiag3 жыл бұрын
`i would fix the PATS issue first, then double check my powers and grounds at the pcm, if no comm then get new pcm.
@richardmarkham83693 жыл бұрын
@@DallasAutoDiag The PCM was dead. Probably blown due to low battery. Send it off to ECU Testing who couldn't fix it so they cloned another PCM. PATS issue was just reporting that there was no PCM detected.
@thestateofreal25333 жыл бұрын
I have the same problem on my 2017 focus but no blown fuses.
@thegreenboyuk2 жыл бұрын
Did you fix it?
@witsasmusic5957 Жыл бұрын
Same
@reyaadahmed12873 ай бұрын
Hi I see the engine ligth flick and thats the problem I'm having when i turn the key before starting its flicks when I start no engine ligth the car lacks power and drinks fuel anyone with some help please New injectors are in the car coil packs are fine no vaccume leaks
@musicent430Ай бұрын
Man im havin trouble rn smh 6 days now car sittin , gettin same issues , dashes on odmeter , hill assist , low tire pressire , engine fault , i checked all fuses thyre good here the codes im gettin from forscan p0443-c purge valve circuit fault u1262 scp data link fault p0460 invaild fuel tank level p0113 iat sensor p0602 pcm prog error p0174 system tpp lean bank 2 p0443 purge valve circuit fault b2308 interior air temp b1318 battery volt too low b1994 side air bag b1877 saftey belt retractor b1244 rear wind wiper relay b2256 heated windshield b1428 safty belt lamp
@DallasAutoDiagАй бұрын
I think you should find someone to diagnose it for you
@AlejandroRodriguez-ol9mf Жыл бұрын
Very good diagnosis, I have a similar problem, but it's a titanium focus 2012, it works but it doesn't get to turn on. I already followed your steps but it didn't turn on either, any recommendations could you give me?
@DallasAutoDiag Жыл бұрын
You can start with checking all the fuses. Make sure no relays are missing. That doesn't mean you have to put a fuse and relay in every empty spot. Other than this someone specialized has to look at it.
@user-ky7ty3ie1x7 ай бұрын
Did you solve your problem
@juice5440 Жыл бұрын
I am going through the same problem!! I just picked up this crashed Ford Focus st turbo & I am getting no communication from the obd port
@DallasAutoDiag Жыл бұрын
Fuse blown maybe
@user-ky7ty3ie1x7 ай бұрын
Hi did you solve your issue
@anthonyacosta72357 ай бұрын
OK, so what was the problem? Replace #36 and check fuse. I had a recall for ignition control module ?
@DallasAutoDiag7 ай бұрын
It was just the fuse
@rolandonarvios21782 ай бұрын
Where is located # 36
@hugoparedes853 жыл бұрын
I have a bad problem with a truck its a 2014 escape also involve in an accident truck drains my battery real quick and has a missfire on two cylinder even do they have spark,180 compression, new spark plug ,coils dont make any sense i think its got a short
@DallasAutoDiag3 жыл бұрын
Is it 4 or 6 cylinders? Which cylinders do you have misfire on? Which side was your accident?
@hugoparedes853 жыл бұрын
@@DallasAutoDiag its only misfiring on cyl 2 and 3 its the 1.6 EcoBoost
@hugoparedes853 жыл бұрын
Its driving me crazy only has 49k miles and i check compression came back 180 psi ,new original spark plugs coils motorcraft they are firing also switch injectors 1 to 2 and 4 to 3 and problem stays on 2 and 3 they have voltage radio dosent work had a short which i found a wire touchinf ground and was blowing the obd port fuse after that no more blown fuses battery drains in less then a day
@DallasAutoDiag3 жыл бұрын
@@hugoparedes85 battery drains in less than a day huh. you have a big problem there. I would first focus on the battery drain before looking at the misfire. they might be related. Take a look at my las video I uploaded and use the same technique to find out which circuit you have the draw from. then update the comment here.
@DallasAutoDiag3 жыл бұрын
@@hugoparedes85 by the way, was there any harness damage because of the accident?
@carlosreyes445511 ай бұрын
Where are you locate? I have the same problem
@DallasAutoDiag11 ай бұрын
Kennedale TX
@user-ct6ng9pj9z2 ай бұрын
Could mine be thé same
@DallasAutoDiag2 ай бұрын
It could be
@luhnitro177827 күн бұрын
Sir please help me😢 I’m having a similar issue with my car but my car is a manual😢
@DallasAutoDiag26 күн бұрын
Where are you located?
@luhnitro177825 күн бұрын
@@DallasAutoDiag Alabama🥺🥺
@aymenmohamed1134 Жыл бұрын
👍🏻
@DallasAutoDiag Жыл бұрын
👍
@jerryblack1433 жыл бұрын
Could mine be the same issue. I posted the video of my behavior here kzfaq.info/get/bejne/prx4hZCKsrG4ZJ8.html
@user-fr5sx2kk8p5 ай бұрын
Okcv
@DallasAutoDiag5 ай бұрын
Ok
@jcwick0859 Жыл бұрын
i had a problem like this no comm with the pcm or scan tool make sure that main connecter is fully seated in the bjb it can cause no start no communication and your dash will say engine fault
@DallasAutoDiag Жыл бұрын
That also could cause same issue. Thanks for sharing.