Thank you for taking the time to show others how to replace those sensors, you definitely made the job very easy for me. People like you place our community in a better world.

No cap bro. I went to autozone today told me the same thing charged me 68 a piece . Went to a mechanic and was quoted a 1000.. wasted 140 but save a full band thank you

Awesome video bud, simple and to the point. Had same issue here, I said no way I'll do it, I found 2 sensors on eBay and here we are. Thanks bro, I appreciate it

Problem Fixed: Whenever your ECM detects P052B on L33, the first thing to check is your MAF sensor and Camshaft sensor. When the IAT is faulty is going to trick out the PCM and send wrong messages to some units such as fuel injector by pumping more fuel and oil. This will probably damage some other sensors such as camshaft, crankshaft sensor and PCV valve. to fix P052B code on Altima 2013 to 2015 you will need to change the cam-sensor after inspecting MAF sensor, PCV valve and intake air housing. Consider oil change before doing this. Tx

Thank you very much it is well appreciated, its -30degrees c here in Canada and I will have to fix it outside, life saver!!!

Yes i am getting the shaft by a dealership right now..just spent 4k on having them replace the tranny and have gone through 3 alternators in 3 weeks since i got it back

You nailed that video. You’re the man!

Bank 1 or A would be Intake which is on firewall side or back of engine and Exhaust B or Bank 2 would be at front towards rad on 2.5 engine head .

Thanks so much for the video, I was searching for hours trying to find a video for the location of these sensors. Any idea of a part number on these?

I'm having the same issue with my 2016 altima 2.5 litre 4 cyclinder....I replaced the camshaft position sensor on bank 1 and the spark plugs...and its still cutting off...what might be the issue

Ur vid nailed it for us. Thanks for posting it.

Appreciate this... Perfect way of showing it...

Hey quick question is the crank shaft position sensor in the back of the motor? I can't seem to find videos on that either... or it doesn't have a crank shaft sensor?? Sorry just learning mechanic.. I have a Nissan Altima 2018 and no videos on that I'm lost

what was the symptom that car was having to throw that code? My 2015 randomly turns off when idling, sucks when in busy intersections, but I dont have any CEL now.

I have a 2016 altima 2.5 4 cylinder. Codes read P0300 and P0011 would the first thing to change are camshaft position sensor? Car will start idle low then cut off. To keep running got to drop in gear and gas it. But still will shut off if at light and idle shakes rough, HELP! ALREADY PAID NISSAN FOR NEW TRANSMISSION!!!

Help can anyone tell me where the throttle position sensor is for that same vehicle?

I got an issue with bank 1 camshaft but the only thing I found was the crankshaft is that it?

Hello bro, I have a 2013 Nissan Altima and I'm trying to remove the Camshaft position sensors, (P0014) like what you deacribed, and I am having a difficult time removing the engine cover. I removed the 3 bolts and proceeded to moving the cover, but there seems to be something holding it down near the back, on the right side, could you tell me what's holding it? Thank you so much I'm advance.... cheers!

Wondering if you’re still here? I know this is an old video. I’m trying to look at the purge valve solenoid, located at the top of the screen and to the back of where you’re working. The plug broke off of my Altima and I am trying to rewire the new plug in and I’m not sure which wire goes on top and bottom, it is the brown or the purple wire on top?

I’m Having trouble disconnecting the wire connector. Any suggestions? What am I missing?

Where is it located on a 2013 Altima? Thank you

Hello there not sure if you know this one or you've had any problems or since you owned the 2.5 liter but my question is not about the camshaft sensor but the MAP sensor LOCATION i can not seem to find it at all on my 2014 2.5 liter ..and EVERYTHING i find points out to taking the INTAKE MANIFOLD off for a maybe ?? Just desperate here TRYING TO HELP OUT my friends actually. Question is do you know where the MAP SENSOR LOCATION for the 2.5 liter is ? Thank you for any help

Hi, I have been looking for a video for crankshaft position sensor on a 2016 Rogue 2.5. This is the closest year I've found for the 2.5 but is that sensor in the same spot on the Rogue?? I've had people say the CPS is on back of motor - and just remove air box and hose and access it from top. I had been looking underneath.

thank you !!

Replaced the new camshaft position sensor and it wouldn’t start. I changed them back to the old ones and started right back up. What do you think the problem could be? You think I should change the O-ring from the old to the new? Great video btw. Edit:do you think the whole time I had to reset the check engine code?

Any idea why when i replace both it wont’ start? Had to put the old one back in (the rear one) to get the engine to start. Thought it was a bad sensor even thought it was new. Got a new one and have the same issue. Thanks,

Thank you!! Is the one camshaft sensor you pointed out is bank 1 or bank 2

Ok so i located the camshaft sensor im trying to discinect by squeezing the clip but it not budging,was it simple or you have to squeeze hard?i dont want to break it thanks

I bought the camshaft position sensor from Autozone and I have a question. It brought a little packet that has a type of liquid, and I’m wondering if I have to put it on the O-ring and if I have to remove the O-ring to get it all in there. But I don’t need to take any oil out or anything? Just a quick remove and replace? Awesome video btw.

Great video. Did everything step by step. Put the new sensors in. The car still sounds off, takes a while for the engine to turn over too for the push start. Check engine light still on. Did the diagnostic and it still says camshaft………anything possible I could have missed?

Thanks for been clear and quick!

I have a 2014 Nissan Altima s 2.5L Do you buy 2 camshaft position sensors? Or one is camshaft and the other crankshaft sensor?

Did you have any issues starting the car after changing them out? We did it on my buddies car and now when we start up the car it idles for a few seconds and then dies

Perfect. THANK YOU!

Thanks bro bro. Good looking. Take Care 🔥💯

I got P052B on my, does this will apply for my car? Thanks

Any one know where i can see/read on a diagram or video where the crankshaft sensor is on this model...well the 2013 2.5. I replaced both camshaft sensors but it didn't do the job...bummer..

Hey! Great video. Quick question, only my cam shaft A or 1 sensor is bad. Which one is number 1 or A? Thanks!

Hey brother thanks for your video one of a kind because there's one 1 of this year.... I change 1 the top one of the both you pointed at just not the other one should I change both... I changed 1 and it started working more then before should I change both

I have a 2014 Altima and I'm having an issue with -occasional- increased crank time prior to start (like maybe 1 in ~40 starts). Could the camshaft position sensors potentially be the issue? (There are no check engine lights). Thanks for the video!!

Thank you sir!

Thank you Richard

Helped me out! Thanks for the video

What was the issue you were having? Was your car randomly stalling or shutting off? Thanks

Will camshaft be in the same place on a 14 ?

I have the same issue with my 2015 Nissan Altima S. By any chance you know the part numbers from Nissan so I can get the correct parts?

Omg thanks so much i had no ideal what a camshaft was never had it come up on any car I've ever owned when i went to autozone i thought i had to replace the whole camshaft... face plam !!! But hey thanks to your video i have learned something new today 😂 and being a woman some of these mechanics will get it he almost had me buying the whole camshaft which is expensive i was like OMG WAT IS THIS THING??? thank you so much for this video i can have someone else do it now cause ill let him know a youtube video just save me a few thousand he can kick rocks smh my god the nerve of some people and thank god for you an youtube

2014 Nissan Altima 2.5 S I am having issues with bank 1 But AutoZone does not carry where can I buy them at?

Hey which is camshaft the one in the top or bottom please point which is which I got both and they don’t cost the same or are the same

I have Nissan Altima 2019 2.5 S .. where i can find Camshaft Position Sensor bank 1

Saw your video. I may have the same issue. My 2015 Altima has 55k miles. Should this happen?

I have engine and rpm shaking same altima model with code p0171 can u please help

Where is the crankshaft position sensor on the 2013 altima model

Thanks bro big help did u change both or just bank 1

Thanks I didn't know I needed two sensors I'm going back to the store today. And wow $600 for something that only takes 20 minutes tops or less. That's a scam.. the parts alone at an auto parts store don't even cost $200 it's like $140 for two parts that you need. What do they come up with the other $520 at? For literally unscrewing five screws.

did you have any problems? Rough idle or anything?

Thanks a lot for your video Fix the problem

Do they have to be replace in a specific order?

Is the camshaft sensor for 2014 altima located in the same place?thank you

How to change?

Cleaning the Mass airflow sensor....?

Would this work for a 2013 model with the same engine?

How do you get out the wire?

What was it doing b4 yiu replaced them

How do u remove the wire harness? I tried squeezing, and pulling. It wouldn’t come off.

What was your code number for the check engine light

Took my 2015 Nissan Altima 2.5L to O'rielly for the free diagnostics test because the check engine light was on. The code reading it gave was p0014 and the probable cause was the camshaft position sensor. I'm confused on which OEM part to get, there's a part #23731=JA11A and 23731JA11B. When I put my VIN# on the Nissan parts website it calls for part # 23731JA11B.

Is this the same for my 2016 2.5 ?

Thank you so much!

I’m haven the same problem same car too thanks man so much my plugs was also bad I had to sub

Thank you so much ❤️

Neither of those two sensors are camshaft or crankshaft! They are on the back of the motor both difficult to diy but possible

Big help thanks

Thanks a lot.

Thanks

Thank you very much man

Thank you for this but what about a 2011 crankshaft sensor

Are the 2 the same part???

It helped

i thought one of those was the crankshaft position sensor

$600!!! :O

Bruh, why all the talking at the beginning of the video? We didn’t need your own personal backstory, bro. Just show us the location. Y’all make this KZfaq shit harder than what it is supposed to be. You dragging this video on yapping about your experience. 😑