In this video we show how to replace a broken door lock assemble on a Toyota 4Runner from years 1995-2002. If you have any further interest please visit www.2carpros.com *Disclaimer: Please use all safety precautions
Пікірлер: 47
@s_gwalls61062 жыл бұрын
Thanks from New Zealand! Just saved me two hundred bucks, I lost my only key. Now I can just take my key barrel in to get a new key cut, instead of the mobile locksmith coming to the truck
@2carpros2 жыл бұрын
Nice! Thanks for watching!
@GRNS21157 ай бұрын
exactly why I looked up this video! Hope I have the same success!
@TheParchisi5 жыл бұрын
Killer soundtrack
@2carpros5 жыл бұрын
Thanks for watching!
@Mahigeer18 жыл бұрын
Nice video. Thanks for sharing.If I am permitted to add, a bent ice pick can be very useful tool for removing the plastic clips. simply insert the sharp point between the rod and the "U" shaped plastic clip. A needle nose can also be very helpful for holding the rod/s while inserting them in the plastic clips.The installation of the "E" clip on the lock cylinder was omitted, but I can see it in the following segment.
@2carpros8 жыл бұрын
+Hashem N Thank you for your input.
@markgarry7866 Жыл бұрын
Nice vid and instructions! I'd would use the Mark technique for the vapor barrier! Use a sharp razor blade to cut the silicone down the middle, parallel to the vapor barrier carefully, may add an extra minute, but when putting it back together, each half of the silicone around the vapor barrier will stick together perfectly without having to buy more sticky material. Thanks for the great video!!
@TheSnideSniper7 жыл бұрын
thanks, did both locks in one hour today
@danajohnson15747 жыл бұрын
Thank you for the clear and precise video!
@2carpros7 жыл бұрын
Thanks for watching!
@UFGator19725 жыл бұрын
There is only one problem with this video, the locks are not keyed alike. Should you not take the old lock and key and get the locks keyed alike before the new one is installed? By the way, was this a power lock? It doesn't look to me that it is because the power lock switch is black. Viewers need to be informed before they attempt any DIY project!
@tfebres17 жыл бұрын
I think I am having a similar problem, what is the name of the small plastic piece you replaced before you put on the new lock?
@LUCKYIRISHLADY774 жыл бұрын
Can you do a video on replacing the lock on the rear door. I have a 1995 4 runner
@LUCKYIRISHLADY774 жыл бұрын
The back window will Not go down.
@arcangelpr20122 жыл бұрын
Excellent video...the best and professional..thank you..!
@2carpros2 жыл бұрын
You are welcome!
@RobertMOdell6 жыл бұрын
2CarPros. I didn't notice any key lock switch that unlocks all the other doors when you turn the door key. How do you obtain that functionality ?
@garyhunter6676 ай бұрын
Great video, but who else fould themselves tapping their feet and rocking their head to the music?
@julia70017 жыл бұрын
Is it true that a worn out piece in the door lock mechanism may be the cause of repeated failure of the outer door handle? The inner handle works fine but the outer handle needs to be replaced for the 2nd time in a year. The nonpower lock is also functional.
@2carpros7 жыл бұрын
Yes absolutely
@julia70017 жыл бұрын
Thank you for answering my question so quickly and the excellent tutorials!
@2carpros7 жыл бұрын
Thank you so much for watching!
@hugos.50594 жыл бұрын
I’m having issues with my 3rd gen 4Runner in regards to the key and lock/unlock button.. the key only unlocks the drivers door and won’t unlock the rest of the doors while inserted in the drivers door and the button on the driver side door panel won’t unlock or lock any of the doors either... is this the fix for that or would be an electrical issue??? Thanks
@jendys1008 ай бұрын
OEM parts? Plastic clip and locker?
@yamatomusashi141210 ай бұрын
3:16 was this step necessary? thank you.
@GnTGamePlays2 ай бұрын
So does that new key work for the passenger door and ignition??
@2carpros2 ай бұрын
If you get the lock cylinder coded to your old key. Thanks for watching!
@yeebthooj7 жыл бұрын
I'm having a hard time removing the door lock control rod @2:20. The clips come off just fine but the rod won't pull out at all. HELP!!
@addsub497 жыл бұрын
yeebthooj I'm having the same problem. It will not come apart even after removing the yellow clip.
@Elefante886 жыл бұрын
I’m having the same issue problem with the rod. Were you guys able to find a way? Thanks!
@cesarpuente52786 жыл бұрын
Im having the same problem with the control rod too. Did you ever find a way?
@erikhamsa63785 жыл бұрын
Grab ahold of the metal rod right underneath the yellow clip with some pliers... gently pull and wiggle. Not too hard or you might break door handle.
@kevjao2675 жыл бұрын
Yeah me too. i tried using pliers and still doesnt want to come of. Im scared that if i pull too hard, the yellow plastic holder might break.
@pablodiaz-dz8jl7 жыл бұрын
hi my name kalett, and I was watching your video very good by the way and I have a Toyota Camry 1997 and my dorr lock it's totally broken anybody can open it and I don't know how to do, amean can I get those thing in a autopart or I have to order directly with Toyota dealership can you guys help in that one please, I know how to do all the process but I don't know how to get that piece thanks and I hope to hear from you guys...
@2carpros7 жыл бұрын
Check amazon or rockauto.com Hey thank you so much for watching!
@pablodiaz-dz8jl7 жыл бұрын
thanks guys...
@WillisOutdoors8 жыл бұрын
so do you now unlock and start the car with different keys?
@2carpros8 жыл бұрын
Yes, the only way to keep the same key which is usually worn out anyway is to take it to a locksmith.
@stevejette23296 жыл бұрын
yes
@rickbravo97925 жыл бұрын
95 is 2nd gen 4runner.
@RobertMOdell6 жыл бұрын
but your left and right door locks will not match, nor will your tailgate lock.