30 HANDLES IN 30 MINUTES OR LESS! How to Install New Handles on Kitchen Cabinets

Рет қаралды 73,443

Күн бұрын

Hey Gang! Today we're installing these beautiful gold handles on the doors and drawers for the new kitchen! Let us know how you think they look!

Пікірлер: 38

@jessicahites871 Жыл бұрын

I used to build doors and drawers for a living. I wouldn't ever want to do hardware after install. Looks great guys!!

@johnbarnett2804 3 жыл бұрын

I've had the problem with the screws being just a 1/4 inch too short, I just counter sunk the whole a bit in the inside of the cabinets. Looked fine.

@jmadig 11 ай бұрын

Great content! I was thinking that that my pliers with the thread cutting feature would help me if that was an issue. But no, your right, sometimes you need to go to Ace for those metric threads on the foreign cabinets pulls! Thanks for the heads up! Always helpful insight in your videos! Thank you for sharing your wisdom!

@mardopresidente5346 4 жыл бұрын

Great job guys

@taylorr1554 2 жыл бұрын

Great job on the entire job your a true craftsman 👏

@StudPack 2 жыл бұрын

Thx Taylor 💪👊

@wscottparks 3 жыл бұрын

Perfect!!!

@albertshilton5336 3 жыл бұрын

Great video ..one question. What is the typical distance from the bottom of the door for the lower screw of the handle?

@inijahsouljah907 5 жыл бұрын

Gr8 work Sir2💯💯

@john.french 3 жыл бұрын

Great project. Always a good day when you get to place an order to McMaster Carr!

@jeffchandler5520 3 жыл бұрын

Cabinet pull screws are the same as the 8/32 on your electrical strippers. You can cut with the strippers, back out and they will screw right into the handles

@StudPack 3 жыл бұрын

These were metric thread 😡

@TheTravelerMan Жыл бұрын

Please add a video on exactly where to place each cabinet pull on the door for different kinds of handles and door styles. 🙏

@kenmore01 3 жыл бұрын

Great job guys! Since you asked, what I would do differently is to put flat washers between the screw heads and the wood to make sure the heads don't dig in, and use loctite threadlocker to make sure they don't come loose. It's not a criticism because I respect the work you do and it's always well done, but you asked.

@StudPack 3 жыл бұрын

Cool. What happens when your wife wants to change them with locktite 🤔😂

@kenmore01 3 жыл бұрын

@@StudPack Not a problem. Use loctite 242 blue. It holds well, but comes apart with hand tools.

@jmadig 11 ай бұрын

@@kenmore01 I used to know a guy that would eat the blue Loctite to freak people out! He said it tasted like candy! He also ate the food safe grease from the grain mill! Good memories!

@kenmore01 11 ай бұрын

@@jmadig lol, I met a guy selling simple green door to door when it came out in the '90s. He drank it to show it was safe. Lately I used it in a coffee cup and it dissolved the glue holding the cup together. I have to wonder if that guy is still alive.

@angelenaa1912 2 ай бұрын

Hi. Great video I learned a lot. But I do have a silly question, but how did you make your jig for the cabinets and drawers?

@anniewilson6737 2 ай бұрын

❤❤❤❤ I want a jig😂😂😂

@aram7821 3 жыл бұрын

Very informative! Are these 6 in ?

@N_Pet 2 жыл бұрын

Great video. Skip t0 5:30 for handle installation.

@agreer3519 2 жыл бұрын

genius!!

@Esiddik 2 жыл бұрын

I wish you linked the screws in the website I am having the exact same problem !

@Jfinishman 3 жыл бұрын

Should’ve shown a completed view of pulls after installation

@mudder4660 Жыл бұрын

Labor time and plywood is money, a $50 adjustable all-metal jig just ordered. 60 holes thru a wood jig can wallow out the holes.

@andrewssd 2 жыл бұрын

If you didn't have Jordan to drill while you're hold the template, just put some masking tape on the back to keep it from busting out.

@danf6070 3 жыл бұрын

Great vid. Would it not have been worth the time to cut down the long bolts so they fit all the cabinets and drawers? I run into this sort of issue all the time and just grind down the long screws that come with the handle until they're the right length. Usually only takes a couple of seconds per screw. I work by myself so I assume it would go a lot quicker with one of you holding the screw in a wrench while the other cuts it.

@StudPack 3 жыл бұрын

I've certainly cut screws before with the screw cutter on electrical strippers but these were metric plus there were 60 of them plus my grinder (you talking about a bench grinder or an angle grinder?) was at home 😖

@danf6070 3 жыл бұрын

@@StudPack yeah, I use my angle grinder. 60 screws does sound like a lot. I've only ever needed to do a handful at a time. Thanks for the quick reply btw!

@mr.g937 3 жыл бұрын

In my experience sometimes it doesn't cut cleanly or it compresses a thread and then you get a cross-threaded machine screw

@FRUGALNISTA 2 жыл бұрын

Pulls instructions start @5:32

@rickbarber6758 4 жыл бұрын

Did you say McMaster Car? For bolts.

@StudPack 4 жыл бұрын

Yes their website is mcmaster.com I can find anything I need in 6 clicks or less and get it delivered next day regular UPS. Best website on the planet.

@jonpadilla5728 3 жыл бұрын

Well done

@cartilagethesecond 4 жыл бұрын

Did you buy those handles from amazon?

@StudPack 4 жыл бұрын

Yes sure did.

@cartilagethesecond 4 жыл бұрын

@@StudPack thanks !bought the same handles too. I also had the exact same issue and was able to use the 30 mm screws you recommended. Thanks for saving me the headache!