The homemade pcp compressor to fill air guns and diving bootles. Assembly of main pistons. . . . for more interesting videos click ,, HERE " / @paulxchannel
Пікірлер: 136
@jeffreystroman2811 Жыл бұрын
I saw a video from India I think where they took two regular high pressure hand pumps and had a huge flywheel that was driven by a jackshaft and then an electric motor. So elegant and effective I must say I've been gathering parts to make my own. Thanks for the video
@pirtekguy3 жыл бұрын
Minor adjustments to the counter balance so it doesn't go for a walk but otherwise it's a great build especially with the extra features like thermostat and safety glass.
@durangotang16814 жыл бұрын
This vid deserves a lot mor views. Fine job sir.
@robertqueberg46123 жыл бұрын
High quality work. This took lots of thought, to pull off.
@brian21964 жыл бұрын
Just finished watching it. That was very kind of you to lay it all out. I appreciate it. I suppose you own or have access to a lathe and mill. Im saving for a metal lathe, then im going to build a vertical mill and eventually my own 300 bar pcp compressor. Thank you again!
@PaulXchannel4 жыл бұрын
Hi. Look at my first pcp compressor video . There are any information.
@jubayerhaque11 ай бұрын
But why do not giveing description of the accessories or metrials pls give me that link of parts and how to make it
@jafinch783 жыл бұрын
Wow! Impressive, thanks for sharing. Great video detail walking through the assembly and parts.
@PaulXchannel3 жыл бұрын
Thanks for watching
@dom21164 жыл бұрын
Excelente, enfriamiento para los pistones, piensas en todo.
@michaelgriffin1205 Жыл бұрын
Beautiful work my good sir! A+.. all im down is a lathe been wanting one.. maybe this motivate me..
@brian21964 жыл бұрын
Awesome Paul! You're a pal thank you for the video! Haha Excellent!
@PaulXchannel4 жыл бұрын
Thanks
@gertjevanpoppel7270 Жыл бұрын
Excellent video and thank you for sharing 👍. Both pistons seem to make compression on the same time , shouldn’t they be 180 offset ?… So if 1 piston is compressing the other one is open or at suction ?…. Or can it be in this sett up because the difference in piston diameter ?. Is there more information to be found somewhere on the how and why ?…. Thanks again for a great diy project 😀
@rosanneennis7253 жыл бұрын
Well done that man
@dford3442 жыл бұрын
Hi Paul You fantastic work. I have a FX Impact. Using a cheap China compressor. After seeing your compressor design I would like to build my next one. I have the tooling covered, Okuma mill and lathe. Would you have drawings are list of your design? Don
@petrglinski52204 жыл бұрын
Super!👍👏
@recklessjunkie Жыл бұрын
This is beautiful
@diy_tigremasacre61763 жыл бұрын
How long did it takes to fill up the bottle and at what PSI did you stop it?
@The_Unobtainium Жыл бұрын
This is BRILLIANT! Subbed
@The_Unobtainium Жыл бұрын
What is the stroke and plunger diameter in both stages? Motor power?
@PaulXchannel Жыл бұрын
6mm 10mm 100mm 1.5kw
@SK-me9by2 жыл бұрын
Wow just Wow!
@adf3603 жыл бұрын
I hope there is a video regarding that sweet spanner wrench you have @ 3:29 in the video. Loving your channel, just stumbled on it this morning : )
@PaulXchannel3 жыл бұрын
Well thank you. I made the key in my workshop. Unfortunately I don't have a video with him.
@doctordapp9 ай бұрын
OK interesting, thanks, as I understand it this is a dual stage compressor, fed with 8Bar from another compressor... Nice work.
@PaulXchannel9 ай бұрын
Yes
@brianlowder81172 жыл бұрын
Have you posted a parts list and diagrams for this build ?
@nitrousman88822 жыл бұрын
Does the counterbalance serve any purpose? The motion of the pistons is driven by an electric motor… why the counterbalance? You might find thermal grease (on the cooling rings) would improve heat dissipation… but really, the detail on the cylinders is brilliant!
@marcusbennett69953 жыл бұрын
Excellent job. I can see where it pushes the air out but where does it draw the air in from?
@PaulXchannel3 жыл бұрын
Thanks. Classic compressor - help with 8bar
@stoffel892 жыл бұрын
Are you willing to share cad drawings of your parts? And parts list like seal sizes and o ring sizes?
@donzone16412 жыл бұрын
I prefer using thermalpaste in heat plate installation, it will improve the heat dissipation much better. You can find it in computer or electrical parts store for sure.
@dhanjitsarma9673 Жыл бұрын
Hi Paul. Very nice project. I am also making one. Can you please share me the size, material used in the block and piston. Also please tell motor hp and wheel size
@jairmachado10974 жыл бұрын
Dear Paul. It was really a nice job!!!! Congrats!!!! have you used stainless steel to manufacture the cyliders?
@PaulXchannel4 жыл бұрын
Thanks . The cylinders are from aluminium. The pistons are solid carbide rod.
@bangagih3 жыл бұрын
Do you have the scheme of this machine?
@griggs3104 жыл бұрын
Самое главное что молчит, и так всё понятно. Молодец!
@kuspriyantobaru1704 жыл бұрын
Di sade mboten kang?
@nielsdaemen Жыл бұрын
Could make some amazing explosions
@paulosoarescarvalho62194 жыл бұрын
Do you have some video with sealings assembly? Would be interesting to see that part. Thank you!
@PaulXchannel4 жыл бұрын
I don't have it at the moment.
@paulosoarescarvalho62194 жыл бұрын
@@PaulXchannel Ok. Thank you in any way. And what is the diameter of pistons ? 1st and 2nd stage you are using?
@PaulXchannel4 жыл бұрын
First piston 10mm . Second piston 6mm. Stroke 120mm.
@redgum13403 жыл бұрын
Hello, if you were to use opposing cylinders, do you think it would work twice as quick?
@PaulXchannel3 жыл бұрын
in the same way
@Z-Ack Жыл бұрын
I dont understand how the regulator/. Oil water separator works when its on the inlet side.. or why the high pressure line wasent used on its connection., wouldnt that too be at high pressure if its reading the pressure in the system? No comprende
@raymundoortiz72694 жыл бұрын
did you make the check valves? or you buy them?
@PaulXchannel4 жыл бұрын
I made the check valves.
@3_TM4 жыл бұрын
Tolles Video und Projekt! War sicher viel Arbeit, was hat dich das ganze an Zeit und Geld ca gekostet? Wie lange hat es gedauert, bis der Druck in der Flasche auf 3500psi war?
@PaulXchannel4 жыл бұрын
Viele danke. Ich habe das Geld nicht gezählt es ist ein Hobby. Füllzeit eine halbe Stunde.
@mbahcarrier16292 жыл бұрын
success for "Paul X"
@normanhalabi15823 жыл бұрын
Very impressive and interesting setup you got. How fast can you get 300 bar pressure in a 2 gallon tank? Can you make a higher grade faster compressor if ordered?
@PaulXchannel3 жыл бұрын
Thanks for watching. I don't have a measured filling time. Approx 2-3h.
@antoniolaracalvache76763 жыл бұрын
No sólo saber los componentes, sino donde comprarlos
@oktogen1476 Жыл бұрын
Very nice! I understand check valves on intake to prevent exiting during compression, but where are check valves on exit to prevent compressed ait back into cylinder? Are they inside that cap that you screwed on cylinder top? Is piston made on lathe have you some idea to improvise it without lathe etc. Overal great construction.
@PaulXchannel Жыл бұрын
the piston is a carbide semi-finished product - it is not machined
@oktogen1476 Жыл бұрын
@@PaulXchannel So where you found it? Yup, carbides are hard but that rod before must have been lathed
HELLO, EXCUSE MY DARE, BUT IT WOULD BE POSSIBLE THAT YOU CAN GIVE THE DRAWINGS OF THE CYLINDER ASSEMBLY, I WOULD LIKE TO MAKE ME ONE. I THANK YOU VERY MUCH, GREATEST GREETINGS FROM ARGENTINA
@omidzamani5630 Жыл бұрын
👏🏻👏🏻👏🏻
@paulosoarescarvalho62194 жыл бұрын
Hi, Very nice job! Congrat! What is diameter of piston shaft first and second stage? And movement lenght (stroke)? The piston itself looks like aluminum with brass on top, am i correct?
@PaulXchannel4 жыл бұрын
Thanks. First piston 10mm . Second piston 6mm. Stroke 120mm. Material of pistons solid carbide rod.
@paulosoarescarvalho62194 жыл бұрын
@@PaulXchannel Ok thank you. And at second 0.54 of movie we can see two brass pieces with side hole ( i supose hole goes in 90º till top where spring sits). - Are this pieces one way valves sit on top of cilinder? How do they seal? Have o-ring or another kind of sellant inside cilinder?
@PaulXchannel4 жыл бұрын
@@paulosoarescarvalho6219 Yes. There are one-way valves with 90° hole.
@paulosoarescarvalho62194 жыл бұрын
@@PaulXchannel How do you did one-way valves seal? with o-ring? And where is that seal? Inside cilinder?
@PaulXchannel4 жыл бұрын
@@paulosoarescarvalho6219 A plastic ring. In first part . ( cylinder head )
@paulmanhart44812 жыл бұрын
Excellent design. Do you sell these? Did you make or purchase all the parts? Thanks, Paul
@PaulXchannel2 жыл бұрын
Made in my workshop
@paulmanhart44812 жыл бұрын
Damn!
@prototype90003 жыл бұрын
Simple design would have went with some bigger pistons though and a multi stage design though
@rosanneennis7253 жыл бұрын
No you wouldn't of
@5tr41ghtGuy3 жыл бұрын
If you look carefully you may notice that Paul is feeding the high pressure compressor from his low pressure compressor (~7 bar). Also, the rods/pistons of the high pressure compressor are different diameters, suggesting that the high pressure compressor itself has 2 stages - altogether that makes 3 stages. If you wanted bigger pistons delivering 300 bar pressure, you'd need a *very* powerful motor! Remembering from physics class: force = pressure * area and suppose you want a 50 mm diameter piston on the final stage: pressure = 300 bar diameter = 50 millimeter radius = diameter /2 = 0.025 m area = PI * radius ^ 2 = 0.0019635 m^2 force = pressure * area = 58904.9 N (13,242 lbf or 6.6 tons) and that only accounts for the final stage - Yikes! As Nikola Tesla once said of Thomas Edison, "His [Thomas Edison] method was inefficient in the extreme, for an immense ground had to be covered to get anything at all unless blind chance intervened and, at first, I was almost a sorry witness of his doings, knowing that just a little theory and calculation would have saved him 90 per cent of the labor."
@icarossavvides2641 Жыл бұрын
You're feeding it with pressurised air? At what pressure? 100psi?
@PaulXchannel Жыл бұрын
8bar
@normanhalabi15823 жыл бұрын
Can it be water cooled?
@PaulXchannel3 жыл бұрын
Now only with air
@tylerdurdencotw3 жыл бұрын
Just wondering, how hot could your cylinders get without the cooling rings?
@PaulXchannel3 жыл бұрын
I think if I turn off the two fans it's about 65-70 degrees celsius.
@tylerdurdencotw3 жыл бұрын
@@PaulXchannel Do you think that is because of the friction of the compressor moving back and forth, or the compression of the air?
@PaulXchannel3 жыл бұрын
Large rotating mass.
@tylerdurdencotw3 жыл бұрын
@@PaulXchannel thanks 👍
@5tr41ghtGuy3 жыл бұрын
@@tylerdurdencotw I'm not sure Paul understood your question, so as a mechanical engineer I'll note that compressing air makes it hotter according to the ideal gas law: en.wikipedia.org/wiki/Ideal_gas_law Solving for temperature, you get T= (PV)/(nR) I suspect heat due to friction is negligible compared to heat from compressing the air.
@SK-me9by2 жыл бұрын
I would ask if you build to order but the $$$$$$ would be that of a nice sports car, lol.
@PaulXchannel2 жыл бұрын
No, I'm not building.
@user-rv8ie8pb2b4 жыл бұрын
飞轮太小,重量太轻,所以运转时空压机老是抖动
@alexamd3 жыл бұрын
плохо вышло ( , правда
@millionmilesman3 жыл бұрын
What kind of “glue” in assembly? Thanks
@PaulXchannel3 жыл бұрын
I don't use any glue - only oil on the O rings.
@bangagih3 жыл бұрын
@@PaulXchannel what oil? Silicone oil?
@PaulXchannel3 жыл бұрын
@@bangagih It can also be machine oil. Mixed into the air in the device.
@WaschyNumber13 жыл бұрын
🖖 👍
@bull_bhopali3 жыл бұрын
Is this available for sale
@PaulXchannel3 жыл бұрын
Not for sale. Thanks.
@antoniolaracalvache76763 жыл бұрын
Muy buen compresor, pero me gustaría saber los componentes para hacerme uno. Gracias
@diy_tigremasacre61763 жыл бұрын
Hola! Cómo estás? Dónde vives? Para piensas usar algo como esto? El fabricó casi todos los componentes.
@antoniolaracalvache76763 жыл бұрын
Cuanto cuesta el kit completo
@diy_tigremasacre61763 жыл бұрын
@@antoniolaracalvache7676 Antonio en que país estás ? Tu puedes comprar un compresor desde los 300$ -3000$ dólares, para qué tipo de uso lo quieres y así te puedo recomendar algo y no tienes que pasar trabajo
@antoniolaracalvache76763 жыл бұрын
España, y el compresor lo quiero para una carabina PCP. Ya se que los venden hechos, pero me gustaría hacerme uno y así me sirve de entretenimiento
@diy_tigremasacre61763 жыл бұрын
@@antoniolaracalvache7676 le voy a preguntar si él te puede fabricar los pistones y las válvulas, pero no te recomiendo eso te sale más caro solo el envío a España va a costar unos cien dólares, sabes que este sistema tiene un compresor regular conectado? Esto es como un multi picador, busca un aparato llamado shoebox.
@jerrycarnrike75973 жыл бұрын
How much I will take 1
@PaulXchannel3 жыл бұрын
Not for sale. Thanks for watching.
@ahmedfocak56914 жыл бұрын
How much did this build cost you? Thanks
@PaulXchannel4 жыл бұрын
I don't know. It is a hobby. I did not count the cost :)
@ahmedfocak56914 жыл бұрын
@@PaulXchannel oh thanks, i converted paintball to bolt action rifle, and i made a compressor from an old fridge, but the power wasn't sufficient. I have a lathe and a mill, but I dont have the money cuz Im 18 years old. I mean if its around 200 euros its not expensive. Thanks for the information Im gonna try to build it if its not that expensive
@PaulXchannel4 жыл бұрын
I wish you a lot of success in the construction - thumbs up for people like you.
@ahmedfocak56914 жыл бұрын
@@PaulXchannel thank you, it means a lot
@Wranhart184 жыл бұрын
I will buy it off you. Please let me know if it's for sell?
@PaulXchannel4 жыл бұрын
Sorry but isn't for sale.
@diy_tigremasacre61763 жыл бұрын
@@PaulXchannel. Hi Paul, thats a nice system and I would like to know if you would sell the necessary parts so I can put on together? And how much would this unit cost if it was ever build with that intention?
@PaulXchannel3 жыл бұрын
Thank you for watching. Unfortunately I have little time to make new parts.
@mehdimehdizade8132 Жыл бұрын
Hi. Pistons are 10mm and 6mm. But what are the diameters of cylinders?
@mehdimehdizade8132 Жыл бұрын
inner diameters I mean
@PaulXchannel Жыл бұрын
10.1 ...... 6.1
@mehdimehdizade8132 Жыл бұрын
Thanks! Do you filter oil from air after high pressure compression?
@mehdimehdizade8132 Жыл бұрын
@PaulXChannel
@PaulXchannel Жыл бұрын
I don't filter
@markhall9124 жыл бұрын
A car ac unit will do 350psi why wouldn't you use one of those
@PaulXchannel4 жыл бұрын
I'm sorry, it's just a hobby.
@markhall9124 жыл бұрын
@@PaulXchannel ok cool I use to make stuff but if I can repurpose stuff I will now time vs money hard to have both
@PaulXchannel4 жыл бұрын
@@markhall912 O.K. Cheers.
@diy_tigremasacre61763 жыл бұрын
This unit will allow you to have 10times that pressure, I don't know why he built one but I can tell you how useful it can be to many, people with off-road vehicles have to deflate and inflate back and forth their tires a 3000-4500psi air tank allow them to do this during the whole trip. Another use for hobbies like, Air rifles PCP to 2000-4650psi, Paintball hpa makers, some airsoft guns and for the lowest end using between 200-800psi water rockets. You could use it for scuba diving, but you will need to have a very nice system of filters to ensure the air is clean and safe to your health. I personally would like to have one for my PCP rifles.
@mbahcarrier16292 жыл бұрын
350 Psi = 24, ..Bar
@chenmengqing2457 Жыл бұрын
Our brand would like to invite you to test our products for free, how can we get in touch with you?
@absolute___zero4 ай бұрын
linear guide? HGR25 or 30? shit, this thing must have cost about 5k USD. no way I will DIY such a machine, just saw PCP air compressor on aliexpress at 158 USD. , 4500 PSI pressure, free shipping
@daniellewis5413 Жыл бұрын
No filters i wauld love to see how much water come out in the tank .!! Coz i use pump to fill my guns and iv seen shit loads ov water in my guns coz filter gets wet over time .!! Fuck that tank going bang !!! Coz rust eating in side out 😂