What you should of done was construct electrical leads on each corner. That way you would reduced the electrical resistance of corrosion resistance metal plates. This would increase efficiency and reduce the heat in the HHO generator Sir. Hope you keep that in mind when you build another unit of want to upgrade what you made by modifying just a few plates. Also, you need to tweak the car system electronics to take advantage of the OxyHydrogen gas. JOB well done DIYer. v
@user-jp2em5hy5f2 ай бұрын
If the HHO is fed into the intake BEFORE the airflow meter; the flow meter is metering out fuel for a gas mixture that already contains fuel (H2). Feed your HHO into the system AFTER the airflow meter just for a start. There are other changed engine parameters that need to be tuned for too.
@kentevans4218Ай бұрын
Correct.....same with oxygen sensors. Put spacers/extension between exhaust pipe and ox sensor.
@shaneoneill225425 күн бұрын
Why
@shaneoneill225425 күн бұрын
What kind of spacers. For length
@caseiriks7169Ай бұрын
Did you add an efie, ? Otherwise the ecu detects more o2 and starts to compensate adding more fuel. I disconnected the fuel system and add a SU carby, the ecu only controls the spark and timing. I run a very lean fuel mix and add 180 watts of hho at 15 amps giving me 10 liter per 100 on a 3 liter pajero that used to do 15 liters per 100ks.
@esahg54212 ай бұрын
flash positive charged water over a negatively charged aluminum wire. when they meet, they should create 100% hho with aluminium oxide as a byproduct, which can be heated back into aluminium.
@messiaslavorperrone29482 ай бұрын
I spent 3 years doing all kinds of experiments with hho, I even used Peltier tablets to cool the water, the Idea to know the consumption and use the scanner to know the injection time.
@amirgedon20 күн бұрын
i think u should step down dc fuel pump and injector from 12v to 8-9v. My opinion.give me your update..
@rexford90192 ай бұрын
Voltage should be around 1.7 VDC per cell, target amperage should be .25 amps per square inch per cell. Use cross hatch pattern. HHO implodes during ignition. Water fog injection is needed to emulate slower burning fuel such as gasoline.
@SKAD_692 ай бұрын
2Н2О >>>2 Н2 +О2 !!!!!!! 😅😅😅😅😅😅😅ННО 😅😅😅😅😅😅😅😅😅😅😅😅
@godwinsboomАй бұрын
2H2O =HHO + HHO
@quantumenergysolutions912814 күн бұрын
Incorrect! The reason the graphite cell was shedding was because he used way to many volts with the Urea electrolyte. It only needs 0.3v per neuteral cell! He could have had 18 cells with only 5.5V.
@gearscodeandfire2 ай бұрын
Great build video. I am working on something very similar. Is there anyway for you to estimate how much gasoline was needed to replace the charge on the battery?
@albertnario48772 ай бұрын
i can't compute it when it comes from the engine.. i don't have intentions to charge it from the alternator, instead it is solar or grid. it makes it cheaper that way
@pcpatel012 ай бұрын
Had received a few suggestions. Hope it helps 1. Use a powerful flashback arrestors- preferably 2 one near the hho kit after the bubbler and 2nd near the air in-take. 2. HHO input after the MAF(Mass air flow) sensor and not before. p.s. these are just some suggestion that - do it on your own risk
@albertnario48772 ай бұрын
yes, thanks 👍
@shaunhall68342 ай бұрын
Hello from Colorado. Excellent work!
@albertnario48772 ай бұрын
thanks sir
@mrsunyofficial10 күн бұрын
amazing tips
@DaVeHiLl2002 ай бұрын
🤫 Perforated metal sheet has a larger surface area, also if your gas can't get away from anode/cathode fast enough you're generation efficiency goes down as you're using less or the available surface area. The water heats up because stainless steel is very resistive, platinum is the perfect material to use but it's too damn expensive. Low voltage, high amps is apparently the way to go or high voltage low amps pulsed at quite low frequency to keep temperatures down. I wonder how well 240v at 50hz rectified would perform? With graphite plates the problem is that it's very sacrificial, no good as you seen, not for anode anyhow. We need to use an anode that can't be used for electroplating yet is very conductive and does not erode or corrode. If you think of a cost effective material that fits requirements please let me know 😊👍
@MiloBeni51692 ай бұрын
Este video nos anima a seguir haciendo lo que la mayoria de las empresas se niegan a reconocer. Felicitaciones por el video, seguramente seguiras desarrollamdo este sistema, y estaria bueno injectarlo directamente. Habra que reprogramar la computadora y agregar un compresor a diafragma para que sea capaz de generar 3,5 bares. Asi se puede usar el injector del auto y evitar explosiones.
@unikzacontrutora2 ай бұрын
Tests should be conducted on vehicles with 5th generation GNV systems. As they already have more advanced equipment that allows changes in the systems and can better accept HHO. As an admirer of the HHO system here in Brazil, I am interested in learning more about its applications and benefits.
@esahg54212 ай бұрын
put a positive wire onto a tap with water, so that when the water drops out it carries a positive charge. then put your negative terminal onto some aluminium wire (like used for welding) when the positive water meets the negative aluminium, they should flash into 100% HHO, the byproduct will be aluminium oxide, which you can reuse again by smelting it back into aluminium.
@EustaquioNunes2 ай бұрын
Eu também tenho muito interesse nesse sistema, desejo troca de informações. I am also very interested in this system, I want to exchange information.
@johncollins19692 ай бұрын
My gosh you are very clever. Thanks for the video.
@Matt-wb7lm2 ай бұрын
Very ingenious, your on your way to something positive.
@vincentcliong2 ай бұрын
Have you try using 4x LiFePo4 battery to replace accu in gasoline car. It saves fuel more than 10% and no maintenance needed.
@idontknowmyfirstname692 ай бұрын
Did you have any problems with your electrolysis cell getting hot? It appears to be a lot of current for the volume of the cell
@albertnario48772 ай бұрын
it's getting hot without the PWM.
@jozefsetlik70502 ай бұрын
After just a few minutes, such a cell boils and the insulation that needs to be used is PTFE. another disadvantage is that stainless steel plates corrode and the electrolyte turns into green soup. For many years I have had contact with devices from OWELD, which produces such devices intended as gas welding machines. a better solution for a car is an oxygen cylinder with a volume of 5 liters and a tube leading to the air intake. The engine has a great kick. You have to be careful not to overheat the pistons.
@philjoyce79392 ай бұрын
Urea and potassium hydroxide? So how do you dispose of the chemical mix that remains after electrolysis to exhaustion of the hydrogen?
@kevinlsims73302 ай бұрын
Clean Your Drains With It?
@kentevans4218Ай бұрын
Legit test.....good job!! You need to put an extension piece between your oxygen sensor and the pipe. That way the oxygen sensor won't tell the computer to make the fuel mixture more rich. Heat i@the challenge on these HHO generators. Maybe try less electrolight.
@sridharboyana92502 ай бұрын
I liked your experiment. I am planning to build one for my bike {350 cc carburetor bike}. I understand that graphite has a smaller lifespan to SS304. So I made my plates with 316L which is more anti- corrosion. I was thinking in the same lines as not to overload the alternator and considering a separate power supply. I intend to publish the results on my channel when I get to where you are presently. I was also thinking to install a wind and solar generator to charge the additional battery on my bike. One factor which I would like to consider is de-carbonization of the engine(while using HHO) over a time period which may result in better efficiency. Instead of HHO. What performance one can get of ICE if it pure hydrogen? This is my unanswered question so far. All said and done I respect you for the time and energy to make the video and sharing. Thank you. Bless you
@Siriusinfo18 күн бұрын
😊
@AngelRodriguez-mb2vv7 күн бұрын
Tal vez no era para más potencia pero si para más peso eso k le puse en un auto iría haciendo maravillas x la carretera
@Timothyis2 ай бұрын
Looks wonderful - Canada
@Woffy.Ай бұрын
If you look at the short term fuel trim through the OBD 2 you should see a drop as the ECU changes the injector pulse width, this way you can keep the ECU in the system and avoid a lean burn condition which is not good at high RPM. Also to mitigate intake explosion by fitting a flap valve after the Throttle body to release excess pressure from the intake plenum. I had Lexus LS400 V8 on LPG / Oxygas. Good effort.
@technokid414Ай бұрын
Can you tell me more about your lexus LP setup? I want to do the same to my vq25 engine.
@slimel-gharbi81702 ай бұрын
Great, very informative experience except that oxy hydrogen (HHO) is dangerously explosive if the detonation is too strong!!! it is better to complete the assembly with a separation system to obtain the hydrogen AND the oxygen each on their own
@albertnario48772 ай бұрын
yes it's very explosive ,bubbler tank is very important.. oxyhydrogen is already good in the engine ..
@CoincidenceTheorist2 ай бұрын
Stop trying to scare people. Why are you here? Hmmm
@slimel-gharbi81702 ай бұрын
@@CoincidenceTheorist Try to scare people!!! No, but am I dreaming or what? I'm just informing these people of a scientific truth that everyone should know It's YOU who SHOULD normally warn them and you don't do it, you mislead them!!! and it’s serious! Try doing this experiment on a small scale to convince them: Don't forget that I am here because I choose to be
@DaVeHiLl2002 ай бұрын
There's always one health and safety bot hiding, waiting for their opportunity to chat poo 🤣🤣
@DaVeHiLl2002 ай бұрын
If you want to separate hydrogen and oxygen you can do it with a powerful magnet or electromagnetic as they are opposite magnetic polarity... That's what I came to say but the health and safety guru distracted my attention 🤣🤣👍
@ikifkifАй бұрын
what are the middle layers og graphite doing if there not connected?
@davidrobertson198022 күн бұрын
Yeah the graphite experiment is quite interesting, I wondered why they're not connected too in such a small build.... I actually used a neutral plate every 3 stainless plates in my builds.
@user-jm7wl5bj3w2 ай бұрын
Молодец , возьму на заметку .
@slimel-gharbi81702 ай бұрын
do you plan to carry out the experiment with HHO?? If you have the possibility I suggest you also test the separator system and share your thoughts with us Thank you so much
@slimel-gharbi81702 ай бұрын
планируете ли вы провести эксперимент с HHO?? Если у вас есть возможность, я предлагаю вам также протестировать систему сепаратора и поделиться с нами своими мыслями. Большое спасибо (Я не знаю, возможен ли автоматический перевод!!!)
@user-jm7wl5bj3w2 ай бұрын
Я сейчас очень далеко от дома по работе, по приезду домой хочу поэксперементировать@@slimel-gharbi8170
@fishingwithhusnainmani50302 ай бұрын
Sir plate ka size or thickness please
@davis4921Ай бұрын
How much electricity is required from battery to generate hydrogen from this generator?
@siov42792 ай бұрын
I Just though of something really interesting! What if you installed that potentiometer on the gas pedal somehow so that when you press it down the voltage will increase so you can possably get even better milge so the Oxyhydrogen is more abundant when accelorating? would be even better if there was some sort of storage tank and pressure gauge with some regulators etc. is this something that could make tis even better? or too much?
@kevinlsims73302 ай бұрын
Explosive!! There Is A Reason This Is Not Replacing Fossil Fuels!
@sridharboyana92502 ай бұрын
hydrogen production by increasing voltage (not preferred) but current is. the impact of increasing current takes a few seconds to produce more Hydrogen, may not align with throttle response, just thinking not done it yet to tell you for sue
@monamo4Ай бұрын
hello , is your channel open for sponsorship ?
@MohamedAshraf-oo5wdАй бұрын
How do you control volts and Amps onto this HHO system??? 👍
@torrielandsman4625Ай бұрын
the current is controlled by how much electrolyte you put into the mix, more electrolyte = more current. as the solution warms up it becomes more conductive and can run away on you. one way to help controlling heat is by useing six cells in series just like a car battery.
@mr.RICHCH2 ай бұрын
Bravo🎉
@newageautotechnology2 ай бұрын
Nice job
@siov42792 ай бұрын
as you state the pressure gets too high over 850. Although you have the setup for better containment already. that case for one! you just need to get some metal containers of somekind for the other parts that hold the electrolite?
@siov42792 ай бұрын
then youill t need to worry about going up in flames!
@luisacevedo35702 ай бұрын
interesante demostración empírica, habrá una forma de aprovechar solo el hidrogeno? es decir tocar solo el gas que sale de los cátodos? Saludos desde Chile interesting empirical demonstration, will there be a way to use only hydrogen? That is, touch only the gas that comes out of the cathodes? Greetings from Chile
@eugenesits2 ай бұрын
take a look at the amps, if You put an additional batteries for HHO this could give You something. But in general You will have a hybrid car, petrol-electrical.
@jacaliriooracionyfe.37022 ай бұрын
Las dos placas de grafito del centro que función cumplen?las veo aisladas de las de los lados y sólo trabajan las de afuera.
@josegante69829 күн бұрын
es correcto. estan aisladas. funcionan como divisores de tension..
@str8up59823 күн бұрын
I worked with this a few years back but the nay-sayers got to me. Keep up the work. How is the fuel economy now?
@briangattrell2195Ай бұрын
2.6 volts is more efficient you need to add neutral plates to divide into cells to get to 2.6v from 12v.
@albertoramonacosta12122 ай бұрын
Que es carbono hierro fundido
@Atimar01Ай бұрын
for max efficiency try to get the voltage per cell down a lot. for example experiment with H2SO4 (battery acid ... yes ...) with this, the cell voltage goes down to about 1.3V per cell. also use verry thin plates since a thicker plate heats up more due to electrical resistance. now you'd think battery acid is too dangerous right? well, so is KoH, its just on the other side of the PH neutral.... also, you only need verry little of it, basically you set the max amps with the amount of acid. you can obviously use extra acid, but than you have to set max amps with the controller. also, like @rexford9019 said, limit amps to 0.25A per sqr inch. means larger plates ;) --> better efficiency
@a3electronics1572 ай бұрын
can you test it on diesel engine thanks nice content
@robertoquan16323 сағат бұрын
the 2 plates in the middle are not even touching anything. It doesn't work without those extra powder ingridients?
@albertnario48774 сағат бұрын
they call it neutral plates... it can make HHO generators more efficient. adding Koh in water makes it more conductive.
@vincentcliong2 ай бұрын
Jika 3 liter per menit dan pakai susunan plat paling efisien yaitu -nnnnn+nnnnn- di jarak antar play 0,5-0,8 milimeter itu pun perlu setidaknya 600 watt sebab di kondisi paling efisien pun cuma 0,1 liter per menit gas HHO tiap 20 watt. Jika 3 liter per menit accu dan alternator tidak akan cukup untuk memberi supply daya. Kalau andaikata kurang efisien perlu 850 watt maka hasil gas dengan susunan plat seperti di video mustahil 3 liter per menit, separuh sudah bagus sekali. Perlu accu yg di charge. Maka bukan mobil ternaga bensin saja tetapi, mobil tenaga bensin + accu. Pengujian jangka pendek bagus cuma apa menguntungkan jika dipakai jangka panjang?
@johnslugger2 ай бұрын
*_To make a real difference you need at least 200 to 300 amps! I do like your 4 plate BI-POLAR CELL However!!! That's smart!!!!!!!!!!!!_*
@luisalfonsoarteagacorredor7834Ай бұрын
En dónde encontramos la tarjeta y resto de cosas??
@antoniosestar36712 ай бұрын
Did you notice any power gains from HHO?
@albertnario48772 ай бұрын
i didn't notice any improvement on the engine power, maybe on carb type engine, you may notice the difference..
@flappingflight85372 ай бұрын
@@albertnario4877thanks for your honesty! Since you are putting some additional load ( via the alternator) on your engine in order to produce the HHO on board, even neutral power or/and fuel economy “gain” means , that HHO is helping at least a little bit with improvement of combustion .
@albertnario48772 ай бұрын
@@flappingflight8537 no, I don't use alternator to provide power on HHO, I use different battery for it.
@Endless_science_2 ай бұрын
What is this material? And how can we use this hydrogen to start a motorcycle?
@SKAD_692 ай бұрын
ЦЕ ЧИСТА НЕРЖАВІЮЧА СТАЛЬ!!!!👍👍👍
@Endless_science_2 ай бұрын
@@SKAD_69 What??????
@user-wh2fx6pf4n2 ай бұрын
You can’t you would need another engine it can’t run on his car either he’s fooling people
@ianbottom7396Ай бұрын
Despite your efforts I doubt that your reduction in petrol consumption is greater than the cost of the energy input for the HHO
@mickgatz2142 ай бұрын
Who was watching the angle grinder disc slowly get worn away?... 😂
@elarcadenoah90002 ай бұрын
link from graphite plates and prize ?
@albertnario48772 ай бұрын
s.lazada.com.ph/s.jh18z
@elarcadenoah90002 ай бұрын
@@albertnario4877 ok thanks
@user-hs1on8gl6x2 ай бұрын
the big problem of that design is HEAT and low conversion of liquid into gas. i suggest that you study or find the right resonance frequency of water; ;if you found it you can now easily separate the hydrogen and oxygen very fast with 12volt and 3amp power supply only without additives'..and your reactor metal mush be like in a catalytic converter. hope this will help to your experiment
@user-pt9vg7kv8n2 ай бұрын
I want one, let me know how much.
@raufshahid423221 күн бұрын
Temperature high ho ga
@davey2k12Ай бұрын
You know there's a nasty chemical left over when the stainless breaks down what you using in the water
@joemason91872 ай бұрын
Possibly an EFFI filter to basically lie to the ecu about the air/fuel mix, and definitely PWM you will improve fuel efficiency with EFFI ice vid old bean
@antoniosestar36712 ай бұрын
How can the ecu detect thought o2 sensor the additional oxygen, when the reaction of hydrogen and oxygen form water?
@joemason91872 ай бұрын
Well I'm just saying what I had to do for the transit, had to put an EFFI filter attached through back of the obd port, trouble was that before I put that on I thought I was getting better fuel consumption, in a way I was but at cost of more fuel input but that ceases when you add EFFI plus van is quieter faster on the uptake
@marcnavarro629722 күн бұрын
No only hydrogen generator, but oxygen too...
@escalibur55576 күн бұрын
Realiza las pruebas en un lugar más silencioso, parece que tuvieses un aeropuerto al lado.
@haslanchehassan60242 ай бұрын
Tenaga taidak boleh dicipta Pak.
@pen25Ай бұрын
Lol. This is just too funny.
@luisalfonsoarteagacorredor7834Ай бұрын
Deseo q nos traduzca este súper video
@albertoramonacosta12122 ай бұрын
Impresionante lo que produce en 4,2km no podra mucha producciin otros dicen que debe producir 100litro por minuto para ser eficiente en un coche cual sera la verdad Arg
@mickgibson370Ай бұрын
It take electricity to make the hydrogen! And if you are burning in your car take 2 times much and 1/2 the power!
@ernestlageman15538 күн бұрын
The 304 stainless steel wil after a short stop to creator gas . The water turn in to red. Whe have stopp whit our projects in car
@gregooify2 ай бұрын
🤯
@marcoantoniomanes50732 ай бұрын
I´m from Brasil. Make a video with a diesel pickup.
@albertnario48772 ай бұрын
I don't have a diesel car..
@marcoantoniomanes50732 ай бұрын
@@albertnario4877 would it be possible to use H2 +O2 , in diesel motors whithout causing overloads ?
@albertnario48772 ай бұрын
they say it will work..
@cosh7670Ай бұрын
ماهي الفكرة من هذا
@clintonlau58262 ай бұрын
Your plate sanding wasn't done right , that is done in a cross stich pattern by sanding diag top corner to bottom corner of the plate then do again corner top accross to bottom corner like an X pattern getting everything fully sanded both sides it makes a huge differance. Also port it in were the vacum on the brake master clinder connects faster delivery . Good Job well done
@cindys18198 күн бұрын
All this is cool, but in real world terms: how much percent fuel ecomony gain can I expect? What are theveffects on Hp and torque and...ENGINE LIFE?And is there anyone making a really SAFE And Honestly EFFECTIVE HHO Generator Kit?
@Rick1234567SАй бұрын
Use it to make a steam engine you will get millions of views.
@chronobot20012 ай бұрын
I wonder if your car computer was able to compensate for the leaner exhaust by increasing the fuel being injected. That may be why you didn't see much improvement using the lower hho flow rate. The higher flow rate may have been too much for the computer to compensate for. Fooling the O2 sensor may result in better economy with hho.
@antoniosestar36712 ай бұрын
why would be mixture become lean? The additional oxygen from HHO form water when burned
@albertnario48772 ай бұрын
maybe it's better to use it on an older engine. on my first video about HHO, 1.2L/min oxyhydrogen can increase rpm by 200 in the carburetor type engine..
@flappingflight85372 ай бұрын
@@albertnario4877on the older carbureted engine most probably there is no idle RPM stabilisation/ regulation system that is why idle RPM increase .Since HHO must increase the rate of burning of the mixture, it’s equivalent ( as a result) of increasing the ignition timing advance angle ( the idle RPM are stabilised by varying the timing advance angle in most of the modern EFI engines ) . The fact that the idle RPM increases with 200RPM , means that HHO is doing something positive for the combustion process. The energy balance ( energy spent on its production / increasing energy efficiency production from the engine ) is another story .
@jamiejoker118Ай бұрын
Ino one side produces o2 the other side H2 qestion we only want H2 so isn't there anything we can do with the input voltage to just produce H2 ino it's DC 1.7 25A square 25mm but could we just excite H2 NOT the o2 all that power amps is wasted say 25A ÷ 2 12.5A get the gas we need half the input power we are exciting 2 element's to get 1 I might be way of here lol.
@iriobrixcbrixner77262 ай бұрын
Nós deficientes precisamos explicações faladas e não só visuais gostaria que fosse explicado através de fala
@aleksandarpetrovic66132 ай бұрын
You are skilled man. 850W is too much for alternator, not just for the HHO generator. Try with much less watts, 50 to 300, just need a time to see is there some results (minimum 150km, up to 2000km).
@albertnario48772 ай бұрын
hho generator has its own battery, it doesn't take from the engine...
@aleksandarpetrovic66132 ай бұрын
@@albertnario4877 ok
@rhiantaylor34462 ай бұрын
So the energy to split water into HHO comes from the alternator which typically runs at
@albertnario48772 ай бұрын
The battery for the HHO is separated from the engine.. it has its own energy provider.. it is cheaper to charge the battery than to use fuel.. sorry for the poor explanation on that.
@triblax2 ай бұрын
Center plates are useless
@albertnario48772 ай бұрын
you can call it neutral plates, it's important to have it to maximize HHO generator efficiency.
Lo que nadie dice que la batería calienta los cables, además la rompe en muy poco tiempo hasta que no inventen un buen distribuidor de la corriente, no es muy viable en una palabra, es un ENGAÑO
@davidrobertson198022 күн бұрын
Sadly the car's computer will compensate for the extra "oxygen - it thinks" going into the system and will add more FUEL negating the addition of HHO to the economy. The timing needs to be retarded for a more complete burn also, hydrogen burns infinitely faster than petroleum and if you watch videos on how ICE's work you'll see the plug sparks before top dead centre to make up for the slow burn rate of the fuel. SO imagine all the hydrogen igniting before the piston has reached TDC, it's fighting against itself (the engine) to finish it's travel before starting it's down stroke reducing the power and demanding more FUEL from the petrol tank by the "untrained" computer. Try changing the resistance on the oxygen sensor wherever it is on your car to trick the computer into a very lean running state. This is much better done on OLDER cars and their primitive carburetor driven engines, but can also work on diesel engines quite well. Get a 4 stroke mower running on pure HHO and you'll discover tweaking things faster. I AM a mechanic AND an electronics technician BTW and OLD lol. Frequency is the key here, once you discover the frequency the plates produce gases best then you're getting further. Think diodes and capacitors as a frequency "energy tank" with cascading connections to tweak the input. BTW I have NEVER used chemicals in the water, it's not so good for the environment although pure HHO running motors actually CLEAN the air as the run it through their system. Keep trying friend, it's possible - ask the dead Stanley Meyers!
@jaimeosoriora2 ай бұрын
The problem is more Oxigen (from this cell) then oxigen sensor send more fuel. Please remove Oxigen from HHO. Make only a HH cell.
@antoniosestar36712 ай бұрын
Doesn't the extra oxygen from HHO becomes water with hydrogen when burn inside the engine?
@linctexpilot83372 ай бұрын
The extra oxygen enhances combustion…… More complete combustion does not put more oxygen into the exhaust emissions
@ManuelValdesRojas-nn6lmАй бұрын
Remove fuel. Only use hho.
@thra5herxb12sАй бұрын
🤣🤣🤣🤣🤣🤣
@abpccpba4 күн бұрын
Hope you have not degraded you Toyota Car Systems and warranty. STOP Unknowingly you may be doing long term damage. Like emission requirements at your next DOT registration; new tags.
@maciejpilarski35812 ай бұрын
It isn't hydrogen generator, but Brown's Gas!!! be precise, please!!!
@sridharboyana92502 ай бұрын
he never mentioned h2 alone all the way he said oxy hydrogen. Watch it before you comment
@maciejpilarski35812 ай бұрын
Pecise during writing title for movies, ,cause title describing whole thing!!@@sridharboyana9250
@mukhitdinruziev91202 ай бұрын
This is all bullshit!Don't fool the people by taking away their time!
@user-wh2fx6pf4n2 ай бұрын
Exactly fake misleading liar he is
@SmartfibonachiАй бұрын
Неправильно сделал электролищер и не правильно запитал его,поясню,есть определенная площадь которая эффективно позволяет делать электролиз при условии оптимальных параметров,нагрев к количеству и еще циркуляции,у него же все 3 параметра не правильно при подключении видно как электролит уходит чего быть не должно как и дыма это как раз не правильная работа электролизера,если уже решил делать то можно изучить для начала вопрос.еще и напряжение на ячейку 1.2-1-8в максимум.ну а для легкой повторимости можно выполнить из спирали одна в другую высота 5см расстояние и длину опытным путем
@NixUgriBugri25 күн бұрын
Great another sorceri video ... the only problem that physics doesn't agree ... by the way where the hell the energy is coming from to "generate" the hydrogen ... ? So you convert all the energy back somehow what required to generate the hydrogen .. right ? The engine is at best 34% efficient so just by burning the hydrogen loose energy .. Another total nonsense....
@albertnario487725 күн бұрын
it has its own battery.
@NixUgriBugri24 күн бұрын
@@albertnario4877 and the battery charged by WHAT ? you don't get it right ? this is a scam you are "scamming" yourself...
@mdrafiqul33582 ай бұрын
@user-wh2fx6pf4n2 ай бұрын
Hydrogen would not run the engine in that car why are there so many misleading people on you tube and other sites these days
@anthonyg46712 ай бұрын
He didn’t, he used it in addition to the fuel for increased mileage.
@user-wh2fx6pf4n2 ай бұрын
@@anthonyg4671 lol 😂 this guy
@anthonyg46712 ай бұрын
@@user-wh2fx6pf4n I know It can, I have used one myself ,stopped using it only because it buggered the valve seats . So not a good idea unless the engine is prepared too.
@user-wh2fx6pf4n2 ай бұрын
@@anthonyg4671 hence my first comment you need a different engine as I’ve said 👍
@anthonyg46712 ай бұрын
@@user-wh2fx6pf4n I should have read your comment properly 🥴
@joedee186327 күн бұрын
Good test spoiled by poor video techniques. Too many faults to mention
@iriobrixcbrixner77262 ай бұрын
Eu dei um deslike neste vídeo porque eu sou deficiente visual e não entendi o que se trata este vídeo muito desaprovado
@brendan96982 ай бұрын
Stop wrecking your engine. This introduces water to the engine, after running for a while check your oil. If it turns milky stop.
@SKAD_692 ай бұрын
хто скурив в туалеті підручник фізики , тому усе здається шкідливе або фантастичне !!! 😮😮😮😮😊😊😊😊😊
@user-wh2fx6pf4n2 ай бұрын
@@SKAD_69this dude is misleading people for views he a liar not a truther
@romsaymwiti9387Ай бұрын
It evaporates into steam
@McGyver008Ай бұрын
What a SILLY NONSENSE!!!
@vincentcliong2 ай бұрын
Cara membuat drycell yg efisien kzfaq.info/get/bejne/h5eTraminqvXZoU.htmlsi=eITcJGjN2itlZzdu