5Hz NEO-6M Speedometer with satellites using NANO Board
Рет қаралды 1,587
Жыл бұрынThis video is an extension of the previous one. All you need from that video is the configuration for NEO-6M.
5Hz NEO-6M Speedometer with Arduino
• 5Hz NEO-6M Speedometer...
The default configuration for NEO-6M:
- 1Hz update rate
- NMEA messages
The needed configuration for this code to work:
- Disable NMEA messages
- Enable SOL message
- Enable VELNED message
- 5Hz update rate
Most Cars' Speedometers are inaccurate, and having a GPS Speedometer is one solution to this problem.
I was inspired by iforce2d videos and the amount of information he provided about U-blox GPS, so I created this video to show how to make a similar GPS Speedometer using the famous U-blox NEO-6M with a 5Hz update rate.
Note: The maximum refresh update for NEO-6M is 5Hz.
Arduino code (GPS 2MSG UBX with Button)
drive.google.com/file/d/1pIJp...
Wiring Diagram: NANO Speedometer
drive.google.com/file/d/1y8Jl...
CH341SER Driver: To fix Arduino IDE with NANO
drive.google.com/file/d/1ffQs...
iforce2d GPS video
• UBX binary protocol, e...
U-Blox U-Center application:
www.u-blox.com/en/product/u-c...
Thanks for watching
@getclipzy3645 Жыл бұрын
Your video cool continue ❤
@handyguy4814 Жыл бұрын
Finally the video that we've been waiting for is comin
@3DElectroTech Жыл бұрын
Thanks for your kind words
@bubloomohanrajh2025 11 ай бұрын
great video! i have watched other videos, but u were the best at describing! u have earned a sub
@3DElectroTech 11 ай бұрын
Thanks for liking my videos :)
@Kpop_princess1 Жыл бұрын
WOW❤
@Beebert35000 13 күн бұрын
Hello, thanks for the video👌 can I ask how do configure the code to get it to work on the pin RX2 and TX2 of the esp32 wroom32?
@3DElectroTech 12 күн бұрын
Thanks for the comment, I honestly don't know how to make it work on the esp32 wroom32.
@fotrij8010 6 күн бұрын
is there an end result in the form of a final product?
@3DElectroTech 6 күн бұрын
Yes, there is a final product, the one I am working on now. In that project, we will be making our own PCB. The below video shows an introduction of the project. kzfaq.info/get/bejne/h81gf5aXm829ZWQ.html
@fotrij8010 6 күн бұрын
@@3DElectroTech cool
@KrauseOllyKrause 9 ай бұрын
Any idea how to configure a NEO-M9N so it sends out the required data for this code. Are you able to share your config files from ublox?
@3DElectroTech 9 ай бұрын
@KrauseOllyKrause Check out this video It probably has your answer kzfaq.info/get/bejne/j62Glpyjz6iteI0.html
@3DElectroTech 6 ай бұрын
This new video has the configuration for NEO-M9N. I hope you like it. kzfaq.info/get/bejne/jp1dg5SGvt62eKc.html
@lebinhtruong2328 9 ай бұрын
Tôi có thể sử dụng GPS NEO 6M V2 cho mã này không
@3DElectroTech 9 ай бұрын
The one in the video is Neo 6M v2
💀Skeleton Ninja🥷【にんげんっていいなチャンネル】
Рет қаралды 7 МЛН
andrejko_epta
Рет қаралды 15 МЛН