Testing Hodgdon H4350 vs IMR 4350 with the 143gr Hornady ELD-X in 6.5 Creedmoor. UPDATED 09/27/2018 - All links have been removed to comply with KZfaq content policies. www.patreon.com/reloading
Пікірлер: 347
@claverton2 жыл бұрын
Love it that you admit to being a hermit, same here. Perhaps being a hermit and obsessiveness over reloading are mutually inclusive. A couple of years ago I drilled some holes on the edge of the dining room table the other day for the new reloading press when the missus was away for a few days. When she got back and noticed the holes, she went absolutely berserk, had to go and hide. She still brings it up from time to time.
@tnet69696 жыл бұрын
I love that the majority of your videos start out with you going through the basic loading process. watching you do the same process over and over really helps my memory. You learn by doing and it seems like I am doing this when i am watching. Keep up the amazing work.
@blancs30306 жыл бұрын
With the two 6.5 creedmoors I've had with h4350 had there nodes at 42.4 and 42.5. I've pushed out to 43.5 before with no signs. They both loved the 143 eld-x and they perform great on deer.
@charlesjackson72325 жыл бұрын
My little scale started getting crazy on me. Thought it was going to just have to go in the trash. Turns out it was acting up from static. Wiped it down with a dryer sheet and now it’s good as new!!!
@LoveEncoded8 Жыл бұрын
Chamber chiller is pretty cool. 22:45 watch it blow the smoke out the barrel as it’s inserted. Seems to work well. And if lower temps are maintained your barrel life could increase quite some percentage of good shots. Great video. Thanks for sharing the useful data.
@FullLeadTaco6 жыл бұрын
You're a machine JRB! All these good reloading videos you are pumping out, awesome job!
@Zach1991z6 жыл бұрын
You should make a JRB T-shirt with the quote on it "that's just good shootin brother"
@JH-nf4xd6 жыл бұрын
I'm the one who reported a drifting issue with the little scale. Didn't realize there had been a reply until I watched this video, LOL. Responded in the other post, but a cut and paste here as well: "JRB, I didn't think about the batteries, but I just installed some fresh ones. I'm still having the same problem, which is: once I've calibrated and zeroed (set tare) with the pan on the scale I will get anything from 0.0 to 0.2 once I remove the pan and replace it. What's also interesting is that my tare weight will vary with the pan removed (between 146.5 and -146.7 grains). I can also leave the empty pan on the scale and the reading will drift +/ .1gr just sitting there. I've tried it in several different rooms in the house, so I can't see it being a wind/draft issue." I see that tuma benny and ktmracer358 ! are also reporting similar issues with theirs.
@bikertrash786 жыл бұрын
I've always wondered why hodgdon/imr would muddy the waters with two different powders with the same name. Great comparison video. Keep up the good work!
@fredwaldon20685 жыл бұрын
Brett T. IMR used to be owned by DuPont .Those powders were around for a long time.Hodgdon bought them out and decided to keep the imr formulas for those shooters.
@tomkimbrel41923 жыл бұрын
Just yesterday started using the Hornady Microjust Seating Stem, very good piece of gear. I actually had to wait about 3 months until it became available from Midway. Very pleased with the precision and ease of seating used on a 243 Win. Watching your videos prompted me to purchase and use the microjust, so thanks a bunch!
@garrytalley8009 Жыл бұрын
You would be happier to just have a real competition seating die like a Forster or a Redding competition die that supports the case in a vertical position before seating. Forsters are the creators of that style seating die. They are both good, but Forsters are more reasonably priced.
@Buckillusmaximus6 жыл бұрын
love your creedmoor videos. after watching I tried loading up 143 eldx with imr 4064 and imr 4895 both 35.5 grains of powder and the groups were smaller than imr 4350 totally impressed with creedmoor my axis 2 loves every load I try thanks for all you do on youtube!!!
@nilescoyote48296 жыл бұрын
41.5 with H4350 is my match load with 140 ELD'S, and it was one of the old recipes hornady put on their 140 a-max match loads a few years back. There will be another node between 42.5-43 grains if you care to run that hot, you'll gain about 60fps. One of the reasons many shooters run that high and higher is due to the original loads in hodgdon's load data that went considerable higher. RL-16 is another powder that is awesome in the creedmoor with 130-150 grain bullets.
@benjaminnevins52116 жыл бұрын
Mine defiance with Bartlein barrel shoots so well off the 140 A-MAX match, it almost isn't worth reloading for.
@JohnnysReloadingBench6 жыл бұрын
That's everyone's match load! I will probably not be doing a lot of additional work with H4350 since it's hard to find and the loads are already so well known. I'll be pushing it much harder before this can is empty, though. I want to see if my primer cratering turns to piercing once the pressures get up over 60K, and H4350 is probably the "safest" way to do that since everyone and their brother has already shot it. Should be fun. RL16 is definitely in the plans...I just need to pick up a can. I've got AA4350, RL26, N160 and N550 in the plans as well. Should be fun.
@garrytalley8009 Жыл бұрын
@@JohnnysReloadingBench AA-4350 has always worked second best to H-4350. Having said that I do have a 300 Win Mag load that is my best load with AA-4350. It shoots under 3-inch groups at 300 yards every time. IMR 4350 can be accurate, but the velocities are so much lower than either of the other two.
@Meditech5096 жыл бұрын
I jumped on the Creedmoor bandwagon over three yrs ago, all of my friends said it would be a flash in the pan. And factory ammo was hard to come by. (No pun intended) I have loads of data on this cartridge in all types of bullets, powders, primers, and most importantly weather. I currently am using a Christensen BA Tactical in 6.5 Creedmoor Harris Bi-pod, Vortex Razor HD 4.5-27. The best load I have found for consistency in all weather and temps is the 147gr. ELD M with 42gr. of H4350 Federal 210 Primers either match or regular (made no difference) My SD are around 2.2-3. Hornady brass trimmed to 1.915. Forster press, Hornady full length dies adjusted to bump size. This is consistent just under .5 MOA. Velocity is 2805 at 50-105 degrees. 2997 at 28-50 degrees. Consistent cold bore hits at 1500 yds and under. Anything over 1500 consistency drops dramatically best I can do is 3 out of ten at 1776 yds. Well beyond effective range, I do it just for the lols. Gets right down to after 1500yds grab a 7mm Rem Mag or 300 Win. Mag. I currently have all data on IMR4350, Reloader 17, Reloader 16, H4350 Using bullets ranging from 129-147gr Berger, Nosler, Hornady, bullets. Brass data is now under development. Love my results with Hornady Brass. With this warm of load good for only 4 reloads due to loose primer pockets. Currently trying SIg, Starline, Nosler brass. I have used Lapua and found the small rifle primer does not efficiently burn under 50 degrees and over 40.5 grains of powder. If any questions feel free to ask. IMR 4350 is one of the worst powders due to temperature stabilization. Ten degrees will change velocity of up to 15fps especially once it drops below 80 degrees. SD opens up dramatically also.
@WhatIsYourMalfunction6 жыл бұрын
I'm watching your 6.5CM series with interest as I just dropped my TC Compass 6.5CM into a Boyd's stock. Developing a load when the temps warm a bit is a priority. Many thanks for your efforts.
@tangobravozulu94836 жыл бұрын
Thanks Johnny, was looking forward to this video and kind of confirms what we found with our rig as far as IMR opening up at higher charges. Take care of that cold and be well...
@THutch5566 жыл бұрын
Great shooting and great video JRB, best wishes on the sickness, get better soon.
@dalelawrence996 жыл бұрын
Love the videos. I’ve come back to H4350 with the 140 ELD-M and it shoots lights out on the higher end with a little better velocity touching 2700 FPS. Good stuff!
@JohnnysReloadingBench6 жыл бұрын
Yup, that seems to be the classic Creedmoor load that shoots well for everyone.
@sjohnson17766 жыл бұрын
Thanks for doing this. I've tried using a lead sled and my groups are always much larger than when I'm holding the rifle. Be interesting to shoot a load both ways for the heck of it. Between the sled and the chrono there could be some weird harmonics going on. Thanks again.
@CountryBoyPrepper6 жыл бұрын
Good stuff Johnny! Get some rest and feel better!
@Belbivdevoe5 жыл бұрын
I never take anyone that uses a "chamber cooler" seriously.. but the "we didn't blow our face off" comment made me subscribe
@georgeleeper24196 жыл бұрын
Hope you get better soon been some real nasty stuff going around. I bought both of the scales will give you an update when I get home to try em out.
@iPsychlops2 жыл бұрын
I sent my Howa 1500 off to get threaded for a compensator last March or so. The Gunsmith is amazing, but somehow didn’t get my number and I’ve been busy with grad school so it took me a long time to get back to him (it was ready in July). But I finally got it back. That’s a long way of saying I haven’t loaded for 6.5 Creedmoor in a very long time. I have Lapua small primer brass and I JUST got some Lapua Scenar 139 grain. All the Berger Target Hybrids that I was developing with before are of course not in stock anywhere, so I took a chance and got 1000 scenar while I could find them. I was lamenting not having any 4350 (either IMR or Hodgdon) and about to settle and load Varget (which some people have had decent luck with but it’s not ideal based on everything I’ve read). So it’s past midnight and I decided to double check my powder stock to see if I had anything better… and I found 8lbs of H4350. Thanks past version of me for forethought and having my back! 😊 and thanks to you for doing this video! I love the data.
@ruststar5 жыл бұрын
The shiny spot on the brass head is caused by a rough bolt surface when locking and unlocking it. Cheers
@brett80906 жыл бұрын
Watching Sunday, can confirm.
@jonathandavenport11726 жыл бұрын
Hate to hear it man, I've been sick as shit for two plus weeks now, so I feel ya. This month has sucked, I haven't been shooting once. Hell, I haven't been out of the house much in December (thankfully I work from home)
@daviddale36246 жыл бұрын
Thank you for the reminder concerning the Berger 135s. More expensive with that J-4 Jacket, yes. More accurate, yes! Hornady ELD-X good, yes. Getting the job done! REST!!
@jamesbent25844 ай бұрын
I recently bought a savage axis 2 6.5 CM. which i consider a budget gun for sur I'm shooting .32 inch groups at 100 yrds with 143 grain eldx and 43.2 grains of superformance in hornady brass . As well I'm smacking a 6 x 10 inch steel rectangle target at 600 yrds consistently it goes to show u don't need to buy a 2000 dollar gun and use high end components to group well
@FullSendPrecision6 жыл бұрын
I bought the Microjust thinger for a set of Hornady 223 dies. Great for the money!
@mikesimpson67576 жыл бұрын
Thanks for all your hard work. I'd much rather watch your videos on Sunday than watch football. LOL
@convex74566 жыл бұрын
Lol I'm a hermit too.
@BuntMeister666 жыл бұрын
Great as usual, get some rest, heal yourself. Loads can wait.
@redraiderreloading76125 жыл бұрын
HEY JOHNNY, you still alive.... been anticipating a new video from ya Brother. I I know you have a busy schedule but Maaaaan I need my jrb video Fix ....
@jonlockhart84366 жыл бұрын
On that H4350 I would love to see you use a long drop funnel, see if you can cram a little more in without compressing it. Just my 2 cents Johnny. I am very interested to see you pushing it a little farther. Maybe a long drop funnel would help IMR4350 as well?
@thejohnnybob6 жыл бұрын
I packed in 44.0gr of H4350 behind a 129gr ELD Match. Slightly compressed at 2.800", but nothing crazy. Grouped a hair under an inch in my buddy's RPR. Definitely worth cranking up the heat a little bit on your loads.
@benny12356 жыл бұрын
I did purchase the cheaper scale and it has always drifted from the day i got it. I will try different batteries and see if that helps. I also bought the same hornady dies for 6.5 grendel awhile ago and really liked them.
@bbolte3 жыл бұрын
Thank you for this. Answered some questions I had about reloading the 6.5 CM.
@cogunlover55506 жыл бұрын
Wow good video buddy. Wish you did more with the Hornady 140 BTHP Match. Maybe best powder to use with highest velocity, low SD, and best group.
@ILOVETOSHOOT3 жыл бұрын
So, two years ago, you had covid!
@jackasschicken59225 жыл бұрын
Why do I love hearing "idiot" from smaller you tube channels so much? It doesn't matter whether it's Johnny calling himself an idiot or "think like a cop" explaining "well, that's cuz you're an idiot", I find it funny every single time.
@IBTJn6 жыл бұрын
I have the small scale and it's been totally rock solid.
@MSTRnBTCto-the-moon6 жыл бұрын
It seems that the groups are tightening on at a certain case fill. When you hit about max case fill on the H4350 the group was tight and same with the IMR 4350. Once you went to a compressed charge the groups opened up.
@lancemorgan62616 жыл бұрын
I've always used a tenth grain scale. I'm satisfied with sub 3/4 moa accuracy. I'm sure I could get more but I'm not sure it's worth the time. I completely understand those who do chase after the greatest accuracy and SD numbers they can get I just don't have OCD to that level....yet
@neilharris44626 жыл бұрын
Great video as usual. Feel better!!
@edjett26312 жыл бұрын
Good shooting combo. Nice performance on both powders. Back before 2000, I said a lot of times that if I couldn't load it with IMR 4350, I didn't need it. H-4350 looks to be a touch better even.
@dt38522 жыл бұрын
So H4350 test first and then I4350 after barrels was dirt so it doesn’t compare. Trying clean barrel and then test I4350 first after that H4350
@garrytalley8009 Жыл бұрын
Even AA-4350 outperforms IMR-4350 honestly. Not saying you can't get accurate loads from IMR-4350 just saying they will all be of lower velocity than the others H-4350 is the king and AA-4350 is the runner up in 4350's. Now IMR-4350 beats a newcomer Shooters World 4350 that even shoots slower loads than the other 3.
@freedomhard23104 жыл бұрын
Damn good video! That gun shoots good! I use the 143 ELD-X bullets and love them. I use Hornady brass, H4350 41.5 gr. CCI primer, seated 2.843 in a tikka CTR 6.5. Shoots great.
@corymorrow55306 жыл бұрын
This channel is obviously an acquired taste
@thomasfinnegan84573 жыл бұрын
Aren't most?
@geraldbondoc59746 жыл бұрын
Thx, johnny, and get better soon!
@michaellankford83585 ай бұрын
My rifle likes the same setup. Haven't been able to get my hands on a box of the 143 eldx yet but my rifle just loves the 140 eld match under 41.5 grains of h4350. If the x bullet shoots anything like the match that's all I'll hunt with
@kennywoods8954Ай бұрын
Where are the new videos? Love the channel
@AkA-me-Kenny26 жыл бұрын
Johnny 12/20/17 looking for you. Hope your feeling better! Like your videos! Does your Grand Pa watch and critique you work?
@troyroe60216 жыл бұрын
Hello, this video is a great time passer, very informative hope more to come
@billjohnson536 жыл бұрын
Feel better sir.
@DrakeG3104 жыл бұрын
nice cutaway, your vids are educational and comical. keep it up.
@faithandfarmingtennessee8726 жыл бұрын
Get well soon!
@ltbaker2556 жыл бұрын
I finally got sub 1" 10 shot groups out of my 13o gr Nosler RDF bullets with Lapur brass, CCI 450 primers and 43.6 gr of Reloader 16. The overall length that worked in my Ruger Precision Rifle is 2.778.
@jeffyoung20896 жыл бұрын
Thanks for the great Video! Get well soon brother!
@ewetho6 жыл бұрын
Time to repeat top 1/2 and reaching further while shifting the bullet out to .020" from the lands and retest.
@beenstalkingttv79715 ай бұрын
i have a 6.5CM as well, did you have any issues with firing pin when using small rifle primers?? i want to get Starline small rifle primer brass but i dont want to buy them and them not working with my rifle
@markii68316 жыл бұрын
Both of my Compass 6.5 Creedmoor's shot 1/2" groups with 39 grains of IMR 4350
@groovymoon3 жыл бұрын
With which primer, bullet and case? I just got a Tikka T3s in 6.5 CRM
@tim7of7176 жыл бұрын
For being sick, you're able to keep up the ol' JRB Blather,Blather,Blather. :)
@guns4funfreedomkeeper9995 жыл бұрын
I have a lot of IMR4350 because that is the best powder I have found for my 243 Ackley. From what I have read, H4350 is a safe bet for the 6.5 Creedmoor so I picked up a pound today for testing. I hope i have similar success to what you are having.
@dirtsurfer1476 жыл бұрын
It appears that your Compass likes to shoot warm. Usually it hits better on the second or third shot.
@ericbowen50716 жыл бұрын
Thanks for all of your information and techniques for accuracy in your loads! Cool!
@richrudley26502 жыл бұрын
The 6.5 Creedmoor is an excellent cartridge. But my question is why is is it that several people making videos about loading for accuracy. Use the 6.5 Creedmoor as though it is the standard by wich all other 6.5 cartridges are judged by. As far as accuracy goes. There is one 6.5 cartridge that has set several accuracy records. And that is the 6.5 X 47 Lapua. What accuracy records has the 6.5 Creedmoor set. I'm not saying that the Lapua should be the only one used. But the 6.5 Creedmoor has been grossly over promoted. I am not the only one who thinks that. There is a lot of great cartridges out there. Someone should do videos of other 6.5 cartridges. This is like looking at 20 year old reruns on TV.
@Oregun6 жыл бұрын
Great video. Hope you get well soon.
@glenc41736 жыл бұрын
My tiny waowaaaowaooaw scale started acting funky when the batteries started going dead. Swapped them out and it’s working great again
@Busey71206 жыл бұрын
Who doesn't love some good intimate contact!?!
@brianstokes93056 жыл бұрын
My savage model 12 LRP prints solid half minute groups with the 143 eld-x in the precision hunter line. working up my first handloads for it and will test them this weekend.
@redraiderreloading76125 жыл бұрын
I just got a savage 12 lrp... I had good luck with the 140 eld... do you have better luck with the 143s...
@Jiminico6 жыл бұрын
and hope you feel better real soon.
@milo5551006 жыл бұрын
“Close up glamour shots of powder graduals.” Lol! If the markings on that die are recessed you could use the black nail polish trick? Thank you for another great vid. Been waiting on this one!!
@thatoneguy454c Жыл бұрын
H4350 continues to amaze me. It is my favorite powder for 6.5 creedmoor hands down. It's not the fastest, but it is definitely the most stable powder that I have tested. The temperature and weather change drastically from one way to another here and if shoots just as well at 40°F or 80°F. When it comes to hunting loads or "defensive" loads I can't think of a more consistent powder. What is your opinion Sir John?
@1stFlyingeagle3 жыл бұрын
Own that scale and it just keeps working.
@slightenigma6 жыл бұрын
Looks like you were almost at a H4350 node at 41.5. It would be interesting to see a 2/10 discovery around there.
@mikestrunk32824 жыл бұрын
That's Hornady's factory load btw.
@chipherrick51216 жыл бұрын
Like others have said the book load data for H4350 is very conservative. The nodes on my rifle are 41.5, 42.7, and 43.5 at 43.5 from my 22" barrel I see 2780fps with 140gr eld-m. I am using Lapua and Starline SR brass with no pressure signs.
@bikeboy00126 жыл бұрын
Chip Herrick man try some rl 16.
@chipherrick51216 жыл бұрын
bikeboy0012 will do, I have used RL17 with good results, but bought 16# of H4350 when I jumped in to the CM. Next ti me I at the store I an going to get RL 16,17, and 26 to play with.
@chipherrick51216 жыл бұрын
Dang phone auto correct sorry for the typos
@JohnnysReloadingBench6 жыл бұрын
I'm going to use the rest of this can of H4350 to push things much harder before I move on to the other powders I want to test. So many people shoot it, there's plenty of info and experience of shooting way above max. Should be the safest way to see how the gun acts at higher pressures. I'm curious to see if my primer craters become pierced primers!
@gunslinger76476 жыл бұрын
I have found 2 grains difference between these powders. Add 2 grains to H-4350 then these powders well be the same.and you will get the same results on the paper across the board . No pressure problems if you take care on the top ends
@662rambo4 жыл бұрын
I can’t seem to find H4350. I have some IMR4350, RL17 and Hybrid V100. I just bought a Savage 10b 6.5 CM. I bought the 143 ELDX bullets. I have large primer brass and plan to use CCI 200 primers. Any suggestions on where to start for some accuracy loads??
@jeremylauer5234 Жыл бұрын
sorry for asking question for an old video, but i'm looking for the same scale your using. i looked through the scale review video and didn't see it listed or called out. thanks for any information you can provide.
@darthyoda38612 жыл бұрын
What happened to the beginner series videos? I wanted to go back through to learn more about headspace and they was gone 😕
@GBsPitstop6 жыл бұрын
Get well soon.
@NickFrom12285 жыл бұрын
H vs IMR can really make a difference. I used IMR4198 for years and it was definitely temperature sensitive. H4198 is much better in that regard.
@tomkimbrel41922 жыл бұрын
Unfortunately, my waow scale stopped working, was my fault as it fell to the floor and that was that game over. I then purchased a Hornady small scale and that one is great - very consistent always returns to zero.
@tangobravozulu94836 жыл бұрын
I actually have both, and the little scale is still solid, the large one does not drift however I get the same thing + or - .06 gr. However I have been using the Deluxe Digital Scale from Powstro and it is .05 accuracy and seems for me to be the go to for speed and a bit more precision.
@zedoktor9795 жыл бұрын
Tango Bravo Zulu link to that scale?
@garrytalley80096 жыл бұрын
Johnny you should get a RCBS Chargemaster Lite. Best auto measure on the market. Save a lot of time. Every once in awhile it may get an overcharge but very seldom. All you need to do is put it back in the hopper and do it over to get it right. I use to do what you are doing and after researching decided on the RCBS Chargemaster Lite because it is the most accurate and does not throw very many if any over charges like the competition. It's all because of their trickler being better than the rest even better than their most expensive Chargemaster.
@michaellrussell46122 жыл бұрын
Was watching u shoot 6.5 with different powders The one u thought u had miss fire n pulled bullet n seen bad powder.. How bout the magneto hanging on suppressor??? !!
@zacharyroach19906 жыл бұрын
the scrape on the edge is from chambering, head space.
@JohnnysReloadingBench6 жыл бұрын
Yup, that makes sense. I'll have to do some tests where I look at some brass that is chambered but not fired. I bet you're right.
@xwig165 жыл бұрын
Man, I wish you would go through the same load development and testing with a 28 Nosler. There's not much content out there for the 28 yet. Great videos BTW. I love your content.
@sammyphariss36945 жыл бұрын
Hello You ever shoot a 140 gn nosler partion Sambo357
@hawk270leadflinger95 жыл бұрын
Amen. Avoid human contact!
@darrenguile44226 жыл бұрын
Have you thought about putting your best 143eldx load against horady's factory 143eldx load?
@freedomhard23104 жыл бұрын
I would take that 41.5 gr. H4350 and seat the bullets out longer and see if it gets even better.
@davidhunt16066 жыл бұрын
41.5 is not the top end. You should be able to push around 43gr especially with small rifle primer brass. Book value is ultra conservative for h4350. The pitted primers are due to your firing pin not being bushed.
@JohnnysReloadingBench6 жыл бұрын
I'll be pushing things harder as we go along. I'm not going to worry about bushing the bolt or anything crazy like that (would probably cost as much as the gun!) unless we start piercing primers. I'm sure the cratering will probably be our first failure point when we get those pressures up.
@davidhunt16066 жыл бұрын
Johnny's Reloading Bench I didn't mess with the bolt on mine either. When I still used Hornady I was up to 43.0 with the 142smk and now I'm running 45.1(lapua brass) with a 130 Berger VLD. You'll be glad you didn't mess with the large primers. I'm up to 10 firings on lapua brass and sometimes the Hornady brass primer pockets were done for after 2-3 firings.
@rustyshackleford27235 жыл бұрын
@@davidhunt1606 what were the sings the hornady brass done at 3 firings?
@broken_bot_875 жыл бұрын
@@rustyshackleford2723 Very loose primer pockets. In some cases the primers actually fell out while charging with powder.
@My_You_Tube6 жыл бұрын
Thank you Johny for great videos. What hand-held primer tool are you using in this video ? Thanks.
@ktmracer35876 жыл бұрын
My was waoaw scale has started to drift also I was going to switch battery's and keep an eye on it
@benjaminnevins52116 жыл бұрын
I really like the full length die in the Hornady set; however, the seating die crushes my brass every once in a while. I've never had this happen even with the Lee seater.
@calebw71776 жыл бұрын
You make the best reloading content! You have helped me exponentially with reloading, I purchased a lee press based on your recommendation! By the way they have changed their hand primer you might wanna check it out! Anyway thanks for you content. Sincerely, Caleb.
@shanerhodes9256 жыл бұрын
I have found that 4350 like hotter charges with many of the cartridges I have used it in mostly in 3006 hunting loads and some in 7mm08 with heavy bullets and in several different rifles and usually a full case of 4350 shined the best. But just what I have found thus far thanks for the info Johnny and hope you feel better I know how you feel like sh**
@theeasternfront64366 жыл бұрын
I push h4350 in 6.5 above book max by just a skoash with excellent results. No pressure signs beside a tiiiny bit of cratering just like your gun produces.
@shadowironbank54693 жыл бұрын
Great channel! One of my favorites, im always watching keep up the great work! Have you ever considered taking off your magneto chrono? This may affect accuracy, interferes with barrel harmonics. Just my 2 cents.
@henryhenry58973 жыл бұрын
My powder burn chart says imr 4350 is faster than h4350 but shooting both I found the exAt opposite
@jeffreydohl60365 жыл бұрын
Really loved the comparison. I was really having a hard time as to which powder to use for my 308. Now what I'd really like to see if you can, is how Hodgdon CFE 223 in a 308 shoots with a 165gr Gamechanger. Also a comparison between IMR4064 and IMR4166 in a 243, 308 or 30-06
@donttreadonmining91466 жыл бұрын
I had a question, sorry if you have already addressed in a previous video. Was just wondering why the decision to go with the small primer brass? Thanks for your time and really enjoy the videos!