How to Restore/Fix/Repair a Cracked Vinyl Dash - Toyota Hilux Pickup/4Runner PART 1

Рет қаралды 914,686

3 жыл бұрын

I also restored another dash using different vinyl and it came out much better: • Part 2: How to Restore...
Here's how they both look after a one-year torture test: • What is the Best Way t...
How to Restore a Cracked Vinyl Dashboard WITHOUT Vinyl Wrap, using a Spray Texture Coating: • How to Restore Cracked...
Today I'm restoring an old cracked dash from a 1987 Toyota Pickup Truck using the following steps:
- grind the cracks into a V groove with a dremel
- enlarge vent openings
- fill cracks with long strand bondo
- fill smaller areas with regular bondo
- sand smooth
- apply adhesive to vinyl and dash
- wrap vinyl over dash
- trim excess vinyl
Products used:
Dremel 25 pc kit: amzn.to/3g0dWs3
or cheaper generic Dremel: amzn.to/3v0w1dK
Long-strand Filler, Quart: amzn.to/3pv5t34
Fiberglass filler, quart: amzn.to/3puF4T6
Spreaders: amzn.to/3ptttUi
Dupli-Color Prep Spray: amzn.to/3w3uKE2
Fast Tack 92 by Sprayway: amzn.to/3pCb08b
Xacto Knife: amzn.to/2SaQUps
80 Grit Sand Paper: amzn.to/3vXABuC
Heat Gun: amzn.to/3pwOtcX
Clamps, 4-pack: amzn.to/3vWsnmx
Dash Cap Links:
1979 -1983 Toyota Pickup without Side Defrost Vents: amzn.to/3uWu2Y1
1984-1986 Toyota Pickup & 4Runner: (long recessed area across dash top) amzn.to/3fTvCFM
1987-1988 Toyota Pickup & 4Runner: (As an eBay Partner, I may be compensated if you make a purchase) ebay.us/PVU7qd
1989-1995 Toyota Pickup & 4Runner: amzn.to/2T5rIkh
2003 - 2009 Toyota 4Runner with Speaker Holes: amzn.to/3ghX1Qy
I don't have Patreon or ask for donations but you can support the channel with some rad Yota gear from my store: 6thgeargarage.com/merchandise/
Follow Us:
Instagram: 6th_gear
6thGearGarage
How to Remove 1980's Toyota Pickup/4Runner Dash Pad Cover: • How to: Remove 1980's ...
Here are some other Toyota videos you may find helpful:
How to clean/Restore Toyota Pickup/4Runner Door Panels: • How to: Clean/Restore ...
Toyota Door Disassemble: • How To: Disassemble a ...
Rebuild front knuckle & replace birfield joint: • Toyota Solid Front Axl...
Remove an Entire Toyota Rear Axle Assembly: • How to Remove an Entir...
Install/Upgrade to V6 1" Master Cylinder on 4 cyl Toyota: • How to Install/Upgrade...
Install Toyota Rear Axle Bearing, Oil Seal - WITHOUT a Press: • Install Toyota Pickup/...
Replace Toyota Drive Shaft Center Support Carrier Bearing: • DIY: Toyota 4x4 Drive ...
Trail Gear Hi-Steer install: • Trail Gear Hi-Steer in...
Repairing Toyota Frame - Cut Out & Replace Metal: • DIY: Repairing Toyota ...
Fixing Floor and Rocker panel rust: • Fixing Floor and Rocke...
Remove Headliner in Toyota Pickup Truck: • How to: Remove Headlin...
Remove Toyota Pickup & 4Runner COMPLETE Dash: • How To Remove Toyota P...
Toyota 22RE Engine Teardown: • $100 Toyota 22RE Engin...
22r Compression Test: • How to: Compression Te...
Remove Toyota 22RE Engine & Transmission: • Remove Toyota Pickup T...
Toyota Pickup/4Runner Vent Window Conversion: • How to: Toyota Pickup/...
Remove Toyota Truck Rear Glass Window: • How to Remove Toyota T...
Toyota 4x4 Transfer Case Rear Flange Oil Seal Replacement: • DIY: Toyota 4x4 Transf...
Replace Pinion Oil Seal in Rear Diff: • How to Replace Toyota ...
The Vent Window Conversion: • How to: Toyota Pickup/...
Remove Door Panel: • How to: Remove Toyota ...
LED Headlight Conversion: • How to: Install Toyota...
Repairing Toyota Frame - Cut Out & Replace Metal: • DIY: Repairing Toyota ...
Breaking a Rusty Toyota Frame in Half: • Breaking & Cutting Up ...
Toyota Pickup Fiberglass Bed Review: • Toyota Pickup Truck Fi...
B-Pillar Trim Removal & Install: • Toyota Pickup/4Runner ...

Пікірлер: 914

@geolemon 2 жыл бұрын

As a several-decade veteran of mobile audio fabrication, I can tell you - you WANT the thicker Marine-grade vinyl, and you want "so much heat my fingers are burning". There are tools that are made for rolling and pressing vinyl - you don't want to use your fingers. The thin vinyl will just stretch-out, it's the extra material in the thick vinyl that allows you to stretch it. You could have avoided the seam on the side - thick vinyl stretches enough to pull right across that corner and not have a seam. That dash recess is just a difficult stretch - your technique is fine with making a mold, and you were right to START with that recess. You didn't sand your mold smooth though, so you got texture. If you had sanded the texture out, you also would have created just enough clearance for the vinyl. Win/win. Other than that - impressive to figure all this out on a first effort - really impressive. Great job.

@6thGearGarage 2 жыл бұрын

Thanks for the tips!

@dan-andreichira4734 2 жыл бұрын

This is by far the most sincere DIY video i've seen out there. For everyone of my projects I used to struggle afterwards because of selfdoubt due to the mistakes I made(most of the stuff was first time attempt) but this gives me confidence. Thank you very much for this very informative video!

@R.S.O. 2 жыл бұрын

So basically a diy video of a person trying to do something before actually watching a diy video.. what your saying is this person's failure makes you feel better for failing?

@dan-andreichira4734 2 жыл бұрын

@@R.S.O. no. I'm saying it's good to internalize the fact that mistakes are part of the process and you shouldn't be discouraged when you make them. regroup and try again

@jorgefonseca9225 Жыл бұрын

It's a really fucking hard work on this stuff but after looks like a brand new 👏👏👌👍

@simonwoodward438 3 жыл бұрын

That's solved a 20 year old dilemma for me, I have a cracked dash to repair on a old 944, I currently have a spare which is also cracked so I will that first, cheers for the video.

@maurocont 3 жыл бұрын

oh man...I know all the effort needed to get a result this good, I did this exact same work a couple years ago and made the same mistakes, It's really a lot of work. Great job!

@Bob3519 2 жыл бұрын

Great video. It's one of those things that you don't know how to do until you've done it. Kudos for pulling off the first vinyl and redoing it instead of just accepting the results. Thanks to all the comments that are constructive with advise. Cheers.

@haroonaziz6652 2 жыл бұрын

This is my first video of this channel and I'm amazed how much information one can put in one video I loved the fact that you showed how difficult a diy project can be and the mistakes to avoid when doing it yourself

@philgriswold2133 3 жыл бұрын

Very good timing. I'm just starting on a 1988 single cab 4x4 and, of course the dash is cracked. I think I'll go with the replacement part versus home made. I have a grey interior, but I think I'll stay with the black for the contrast. That seems to be big in new cars. Most videos edit out all of they mistakes, thanks for keeping it real.

@clyderasmussen3678 3 жыл бұрын

Its a lot faster to use a can of spray foam insulation or sealant for filling the cracks instead of bono or fiber filler. Sets up rigid then block sand it down. Brush on liquid contact cement holds best. Use 4 way stretch textured vinyl and some gentle heat. Work from the center outward to the ends. Use lots of spring clamps along the edges. If possible staple the edges that extend around on the back side.

@6thGearGarage 3 жыл бұрын

Thanks for the tips. I look forward to trying this again from everything I’ve learned in the comments.

@agrxdrowflow958 2 жыл бұрын

Contact cement does not necessarily have the temperature resistance as headliner adhesive.

@clyderasmussen3678 2 жыл бұрын

@@agrxdrowflow958 I like the idea of using the headliner spray glue. It might allow you to reposition it briefly as you work.

@Liberty4Ever 2 жыл бұрын

Spray foam insulation continues to expand for weeks. It would produce high spots where the cracks were. There is an expanding foam called X30 for marine and aircraft applications that cures differently. It doesn't continue to expand. It could be sanded and it would maintain the shape.

@gosnellktn 2 жыл бұрын

take a look at other glue options. 3m makes tons of different kinds of glue. i would have used a glue that allows retacking. i am no expert, but i know what using the right feels like compared to using something that is almost the right glue.

@Bruceanddenise 3 жыл бұрын

Thanks for going through all the trouble for me. You've worked through all the ideas I had for wrecked, BMW E30 dashes. Alcantara may be the solution.

@andrewhardcastle7982 3 жыл бұрын

Fantastic dedication ! Thanks for the course in dash repair

@robj2704 2 жыл бұрын

I used a replacement dash cap molded to fit over my bad dash on an 80 Malibu a few years ago. It came out really great. I'd definitely use a dash cap again. Just follow the instructions; doesn't take that long to install. My vent louvers were in bad shape but was able to find used replacements on eBay. You can spend a bunch of money on an interior but if the dash looks bad, it ruins the look of the entire interior. Glad I went the route I did.

@houseofno 3 жыл бұрын

Great job recovering that dash! Definitely worthwhile!

@hugoaguilar3073 3 жыл бұрын

Don't remember the time I clicked on a video so fast... thank you for all the hard work you put into these videos.

@jP-nw7nm 3 жыл бұрын

This just gave me so much hope!!! Thank for this!

@waqasahmed7057 2 жыл бұрын

Now this is one original DIY project that is very natural in its making. Thats exactly how it works. You make a plan then you execute it and you come to know a lot of problems and you tackle them and makes you frustrated 😁😁 I love you man for what you were doing.

@americanpatriot2422 Жыл бұрын

Outstanding video and presentation. I went with the plastic cover for my Dark blue dash for my 91 4x4 truck. Super easy and worth every penny. It even came pre painted with glue.

@6thGearGarage Жыл бұрын

The plastic covers really do look great when painted to match. I recently restored another Toyota dash using spray foam, 4-way stretch vinyl and brush-on glue, and the results were much better: kzfaq.info/get/bejne/jqhpeq59t669foE.html

@4by_yotaguy373 Жыл бұрын

Ok I watched entire video and you definitely deserve an A+ for effort! You demonstrated everything I want to try and more. I was rooting for you the entire time! If it wasn't for the top recess it would have turned out awesome at the beginning. VERY RESPECTABLE VIDEO THANK YOU!

@6thGearGarage Жыл бұрын

Thanks!!! I recently restored another dash using spray foam, brush on glue and 4-way stretch vinyl and the results were much better: kzfaq.info/get/bejne/jqhpeq59t669foE.html

@lauramildon-clews7850 2 жыл бұрын

I have a 1975 Toyota Crown. As I live in New Zealand it is right hand drive. It had cracks in the dash and I repaired it in a very similar manner. I used a fabric backed 4 way stretch vinyl. The adhesive used was made by a company in NZ called CRC. It is similar to the product that you used. This is a very angular dash, but it came out very well

@6thGearGarage 2 жыл бұрын

I think I have heard of CRC before, they have a protective lubricant called 6-56 that I've used before. Good product!

@lovetrump1088 2 жыл бұрын

Love it...thanks for showing how a DYI job actually works...the first time at least. Second time is better, third is the charm!!

@benjaminwhitt6415 Жыл бұрын

Who else stuck around cause dudes just... this was oddly relaxing dude... was just so well made

@6thGearGarage Жыл бұрын

Thanks for watching! I recently restored another dash using different methods and 4-way stretch vinyl and the results were much better! Part 2: How to Restore/Fix/Repair a Cracked Vinyl Dash - Toyota Hilux Pickup/4Runner kzfaq.info/get/bejne/jqhpeq59t669foE.html

@aladwanit 2 жыл бұрын

You should got the dash painted, and get done with it and save money 💰

@sandrafright9048 Жыл бұрын

I have used liquid tape the stuff you can coat wires with. It works fantastic. You can even get Color’s that are close to to Color of dash.

@6thGearGarage Жыл бұрын

Good idea!! I recently restored another Toyota dash using spray foam, 4-way stretch vinyl and brush-on glue, and the results were much better: kzfaq.info/get/bejne/jqhpeq59t669foE.html

@PostalRedneck 3 жыл бұрын

You put in one heck of an effort. Win or lose there was a lot of information here. Thanks for taking the time to try various methods and editing for upload. Reminds me of all the pain I was dealing with on my Suburban build.

@djr1943 2 жыл бұрын

Way to go. Thanks for your honesty in doing the dash!

@desparky 3 жыл бұрын

I remember doing this on my Mazda RX2 when I was 18 (in 1985). I sat the vinyl out in the sun for a while, and then over many hours I slowly and carefully pulled the material backing off the the new sheet of vinyl (started the edge off with a razor blade). I ended up with very sore fingers, but this left me with a super stretchy and thin vinyl. The dash came out almost perfect, although the RX2 dash pad is very simple. I firstly attached the rear edge with heaps of clothes pins, then carefully from the center out, stretched the vinyl to the front edge and attached clothes pegs along that edge. Any other clamps in the middle of the dash would leave an impression on ther, but it might slowly disappear? I later did the same thing to a Mazda R100 which has a way more complex dash. It worked out well too. The only issue I had later was the new vinyl off gassing in the Australian sun, which always left a fog inside the windshield that I had to clean off every week or so for the first few months.

@bigsparky8888 2 жыл бұрын

AGREED...GAS IS GIVEN OFF BY VYNAL...VW's WERE NOTORIOUS FOR THIS...SO CAL DESERTS...WINDOWS MUST BE CLEANED EVERY WEEK...OILS...YUP...TY BROTHER...

@reecenewton3097 2 жыл бұрын

@@bigsparky8888 Ditto Fiats: I had a '69 124 Sport Coupe that nastied up the windows: the gummy stuff was hard to get off.

@kyle9782 3 жыл бұрын

I subscribed when I heard OCD... lol I've got a 95 4runner and been working on it 3 yrs. OCD is required with these trucks. My dash is embarrassing! I think I'll give this a go... Nice vid man...

@elguitarronista 3 жыл бұрын

Dude, seriously. THANK YOU.

@24kRobot 2 ай бұрын

Smoothing out that shoulder in the recessed area while you were at it is an excellent idea. The vinyl will lay much better rather than trying to get it to lay in that tiny shoulder. 👍🏼

@6thGearGarage 2 ай бұрын

Thanks! I later restored another dash using spray foam, brush on glue and 4-way stretch vinyl + spray paint, and the results were much better, but still had a little trouble with the recessed area: kzfaq.info/get/bejne/jqhpeq59t669foE.html Also I put both dashes through a torture test to see which products held up better and the second one was definitely the winner: kzfaq.info/get/bejne/r92bpLeSrbGWfHU.html

@yotakid 3 жыл бұрын

Yes been waiting for this video!

@rickbale3772 2 жыл бұрын

When I have a difficult piece like this, I put the vinyl in the clothes dryer for a few minutes. It comes out very rubbery. A small heat lamp works well also.

@JohnnyAppleSSsseeed 2 жыл бұрын

This video helped me tremendously with my decision for dash replacement options, thank you!

@justindarnell430 2 жыл бұрын

You helped me out a lot I just bought my first father son project that we will be attempting this with just for the experience thanks

@phdr754 2 жыл бұрын

Yeah.. .like another poster, cut out the center of that big tray and Wrap around the edge. Then take material and cover a board. Or a contrasting piece of material. Scrap vinyl but you're just worried about the white edges showing. Doesn't have to be removable. Solid plastic plate.

@frontier9142 2 жыл бұрын

That dip "Trey" in the dash.. I would have just filled that in solid and smoothed it out to match the rest of the dash.. I can only imagine the vinyl in the sun on a hot day is just going to pop up.. you could have eliminated that problem just by filling it in..

@6thGearGarage 2 жыл бұрын

Looking back, I wish I would have 👍

@timbonnefin Жыл бұрын

Gotta say I really enjoyed this DIY video. You did exactly what I know I would have done with the mess ups. Hopefully when I do my dash I will have your mistakes fresh in my mind.

@6thGearGarage Жыл бұрын

Thanks! I recently restored another Toyota dash using spray foam, 4-way stretch vinyl and brush-on glue, and the results were much better: kzfaq.info/get/bejne/jqhpeq59t669foE.html

@Samson-EC 3 жыл бұрын

I have to give you kudos for your patience and tenacity...thks..jc

@rosewd2 3 жыл бұрын

Its like doing a vinyl top, you dont put glue over the whole roof at once or you'd end up with wrinkles. Just do one area at a time and strech

@allenhorton571 3 жыл бұрын

Thanks for making [& including] lots of mistakes-hopefully I can avoid all/most when I attempt dash recover.[for warned is etc etc]

@peteracton6360 2 жыл бұрын

I like the honesty of this video, it’s for real.

@jordanwhite3152 2 жыл бұрын

I have no idea why, but I like your videos. Keep working

@jamyers121 2 жыл бұрын

Have you thought about making a separate "tray" for the top of the recessed section? Maybe use the thick vinyl like the 1st attempt and carefully trim the "hole", leaving about a 1/2" overlap that can be pressed in with a custom tray? And making a tray using Kydex material. I make kydex sheaths and its originally used for molding interior panels for aircraft and marine applications. It can be heated and molded in place. Once molded and cooled, remove and cut to fit and do the final fit and finish. I have made lots of itrms with Kydex. I think it would look sharp! Also, with a minor modification, you can make the tray snap in or out for cleaning. Just an idea to deal with the molding issue plus to give it a little "upgrade".

@6thGearGarage 2 жыл бұрын

I hadn't considered that, a removable tray!

@ryanbrown9346 2 жыл бұрын

I was thinking the same thing!!

@jaimecruzado1350 2 жыл бұрын

ttrrzrzzrzzzèèèèèèèèèèèeèèèèèèèèèèèèèèeèèèèèèèèèèèèeèèeèèèezeeeeeèèèeeèeeèèeèèeeèèèeeeèeeeèzèèeèèèèèeee4eèeèèèèeèèèèeeeèèèeèzèeèeeeeeèèèèeèèèèeeèeèeèèèèèèeeèeèèèeeèèeèèèeeeeèeeèèeèeèeèeeèèeèeèèeèèeèeèe4zeeeeeèeeeeeèèeèeeeeèzeeeeèeeèeee4zèeeeèeeeèèeeèeèèeeèeèèzeeeeeeeèeèèeeèeee4zeeeeeèeeèèèeeeeèèèeeeeeeeèeeeeeeèee4èeeeee4zeeeè4zee4eeeèeeeeeèeeèeeeeèeeèeeèeeèeèeeeeeèeeeèeeee4zeeeèèeèeeeeèeeèzèèeèeeèeeeeèeeeeeèèeeèeèeeeee4zeeeeeeèeeeèeeèee4zeeeèe4zèè4zèeeeeeeee4zeèeèèeeeèèer9r4zr4zttx

@jaimecruzado1350 2 жыл бұрын

⁴⁴⁴⁴⁴

@jamyers121 2 жыл бұрын

@@jaimecruzado1350 frwall)a)lllllllllllcooooooooooooollllllllllllyyyyyytttttttt

@c10zane 2 жыл бұрын

Using a steamer for clothes may help with re-adjusting, car shows that I've watched the upholstery guys use them

@tailopez5106 3 жыл бұрын

Props to you for taking on a project like that. I would’ve got frustrated and smashed the dash by the first attempted you had.

@6thGearGarage 3 жыл бұрын

Haha.. there was a long break after the first attempt!

@TEAMPHY6 Жыл бұрын

It's valuable to see what didn't work. Saves a lot of time and money.

@6thGearGarage Жыл бұрын

I recently restored another dash using spray foam, brush on glue and 4-way stretch vinyl and the results were much better: kzfaq.info/get/bejne/jqhpeq59t669foE.html

@radfourrunner8840 3 жыл бұрын

Good job! Thanks for sharing. I need to do this on my truck, too. I'll try stretching the vinyl around the curves using heatgun before the adhesive phase. I want to build up the recessed part on top because I don't want anything placed on the dash. What do you guys think about using foam, maybe 3/8- inch thick, to fill most of it and filling smaller recesses with the Bondo?

@6thGearGarage 3 жыл бұрын

I considered filling the recessed part as well. I would have dremeled away the vinyl first, then applied spray foam to build the area up, then for the last 1/4 or 1/8", used body filler. Maybe the long strand first for strength, then the smooth on top to finish it off.

@indyjones3287 3 жыл бұрын

Nice video. Maybe try and repair/paint the 80 series before going all in on wrap? On my way to testdrive an 80 series now!

@6thGearGarage 3 жыл бұрын

The only problem I see with painting it is getting it to match and replicating the vinyl texture to blend with the factory vinyl finish. Then hoping that paint doesn't fade from the sun. Hope you get the 80!

@indyjones3287 3 жыл бұрын

@@6thGearGarage Hmmm... Could use a piece of vinyl to texturize the paint, while still wet and then use a satin clear to protect all of it from the sun (would have to paint the whole thing anyway). I passed on the 80 (was looking for a friend), someone snatched it up this morning. Market is crazy right now for anything 4wd.

@clivehorridge 2 жыл бұрын

@@indyjones3287 Love my 80, 12 years owned with 472 k km on the dial. Goes anywhere, and never misses a beat. ❤️🇷🇴🇬🇧👍🏻

@panagiotisharos9625 Жыл бұрын

Congratulations... excellent... regards from Athens Greece..

@6thGearGarage Жыл бұрын

Thanks! I recently restored another dash using spray foam, brush on glue and 4-way stretch vinyl, and the results were better, but still had a little trouble with the recessed area: kzfaq.info/get/bejne/jqhpeq59t669foE.html

@allforwheelsgarage 3 жыл бұрын

Thanks for the shout out, love the tutorial video. Looks like yours turned out Great. Mine is still holding up awesome no problems. I got some updates in the works coming soon.

@99fxr68 2 жыл бұрын

Glad I found you man! I love my 86 Toyota pickup..doing a half ass restore right now. Probably gonna have to binge your channel.

@chriscarey1478 2 жыл бұрын

I own a 1988 Toyota 4x4 and am studying videos to educate myself to do a restoration. I want to say THANK YOU! for the Vienna Waltz! That kind of music is proven to be conducive for learning, unlike the rap cr@p and death metal head banger stuff in so many other videos. Kudos, great job! Quality!

@6thGearGarage 2 жыл бұрын

Thanks! I've been using classical for all my long tutorials. I agree with you 100% on the quality of music in some videos!

@azulmemo 3 жыл бұрын

Your end product looks way better than the original cracked dash! Thumbs up! Good job!

@christopherwaits7852 3 жыл бұрын

Honestly that looks awesome. And the texture looks similar to the soft plastic used in 1990s and early 2000s Toyota’s

@Ben83597 Жыл бұрын

Thanks for sharing both your failures and success. Great video.

@6thGearGarage Жыл бұрын

Thanks for watching! I recently restored another dash using spray foam, brush on glue and 4-way stretch vinyl, and the results were better, but still had a little trouble with the recessed area: kzfaq.info/get/bejne/jqhpeq59t669foE.html

@mfundenimthembu651 Жыл бұрын

You've got some really nice viewers... That's all I can highlight.

@6thGearGarage Жыл бұрын

Thanks! I tried another with 4-way stretch vinyl and the results were much better! kzfaq.info/get/bejne/jqhpeq59t669foE.html

@nataliepotesta1995 2 жыл бұрын

The fact that you kept all your mistakes in the video I have subscribed. Honesty pays off

@6thGearGarage 2 жыл бұрын

Thanks! I recently did another dash using different materials and the results were much better the second time around! kzfaq.info/get/bejne/jqhpeq59t669foE.html

@ronjones758 7 ай бұрын

I think you have a great attitude when it comes to working on old cars. I really enjoyed and appreciated your video!

@6thGearGarage 7 ай бұрын

@lliamthrumble Жыл бұрын

Apparently one of the hardest car diy jobs on the planet

@6thGearGarage Жыл бұрын

I recently restored another Toyota dash using 4-way stretch vinyl and brush-on contact cement. Much easier and the results are much better: kzfaq.info/get/bejne/jqhpeq59t669foE.html

@markw1791 2 жыл бұрын

You rock man.If I can see it done I can redo it. I was 20 and seen a man swap a motor. Went home and swapped the one I had knocking. Fired right up. That was 30 years ago in a apartment complex.Yeah they were mad but i had it done before some one could say no. Used the same truck to go get the motor given to me for free and borrowed a cherry picker.Pulled the old motor and set it in back,and got the new motor and put it in the truck. Because you dont skip like a lot of people do,and even tho it is fast forward i can see and reproduce what you do.Thanks man it helps a lot.

@6thGearGarage 2 жыл бұрын

Most of my neighbors hated me when I lived in an apt, except for the ones who needed a hand wrenching or borrowing a tool

@Eagle031265 2 жыл бұрын

That was a pretty fair and nice try to refurbish that dash. Thanks for your time and share this with us. Greetings from Costa Rica.

@TheFalcro1234 2 жыл бұрын

This is a great result. Thanks for showing your work.

@Gabriel-nd3fo 3 жыл бұрын

Man your dedication is impressive 👍

@mattedwards4533 Жыл бұрын

You have the patients of Job!

@6thGearGarage Жыл бұрын

Thanks for watching! I recently restored another dash using some different methods and better materials and it turned out great: kzfaq.info/get/bejne/jqhpeq59t669foE.html

@H3Humper 3 жыл бұрын

Seeing the end product is so satisfying! Your solution for the top of the dash in the recessed area is great. My idea was to fill it permanently and just have a smooth top

@6thGearGarage 3 жыл бұрын

Filling it in was my plan B. It would have been so much easier without it there!

@H3Humper 3 жыл бұрын

@@6thGearGarage I bet! I was going to ask how it has held up and then realized your video is super recent haha. Has the recessed area still held over the short time it's been finished?

@6thGearGarage 3 жыл бұрын

@@H3Humper Yes so far the recessed area has stayed the same. I'm going to give it some time and see if it bubbles up.

@sankyppp 2 жыл бұрын

Warming up the filler mold/stencil before clamping it onto the dash recess should have helped too. But the end result is awesome. I am all for reuse and recycle, so love restoring them.

@jm-ys3un 2 жыл бұрын

great repair i own 2 chevy trucks from the 90 s both cracked real bad but they are solid plastic , luckily i found 2 good ones at junk yard just got real lucky i replaced and painted the one on my 98 with that vinyl spray looks brand new better than expected

@6thGearGarage 2 жыл бұрын

Nice! This is an old video, I recently restored another dash using different method and materials and it came out much better: kzfaq.info/get/bejne/jqhpeq59t669foE.html

@hurtadoaviles 2 жыл бұрын

Again, another excellent video! Thanks.

@6thGearGarage 2 жыл бұрын

Thank you! I recently restored another dash using some different methods and materials and the results were much better! kzfaq.info/get/bejne/jqhpeq59t669foE.html

@britton6062 Жыл бұрын

to be honest, I think you did a great job. Im not as courageous as you, but I'd give you an A+ for sure. I have an older Mercedes, and dash cracks are a tradition !

@6thGearGarage Жыл бұрын

Thanks for watching! I recently restored another dash using brush on glue and 4-way stretch vinyl and the results were much better: kzfaq.info/get/bejne/jqhpeq59t669foE.html

@danielludlow8960 Жыл бұрын

Hahaha! Dude! I did the same thing doing my room with non textured walls! Sanded and sanded and sanded and sanded...took a break for days or weeks at a time....in the end....I textured the walls!!!! BTW....I like supporting channels that I like so I ordered a couple of hoodies

@6thGearGarage Жыл бұрын

Thank you!! I recently restored another dash using spray foam, brush on glue and 4-way stretch vinyl. Less sanding with the foam and the results were much better: kzfaq.info/get/bejne/jqhpeq59t669foE.html

@_JerryLopez_ 2 жыл бұрын

Great video! Thxu for taking ur time and trying out another solution!

@dostarr Жыл бұрын

Great stuff, love the honesty and lesson learning through the entire video.

@6thGearGarage Жыл бұрын

Thanks! I recently restored another dash with stretchy vinyl and brush on glue and the results were much better: kzfaq.info/get/bejne/jqhpeq59t669foE.html

@mtwata 2 жыл бұрын

First video from this channel I'm watching. This is Chris Fix level stuff. Very informative!

@54alans 2 жыл бұрын

Love the down to earth commentary

@northerntranquility1614 3 жыл бұрын

Nice job turned out great,took a bit of time but you ended up with excellent results.

@6thGearGarage 3 жыл бұрын

Thanks 👍

@jasondavis8741 2 жыл бұрын

Man, that's great. Love to see jobs that show, what how and why. Great job. Thanks

@6thGearGarage 2 жыл бұрын

Thanks for watching! I recently restored another dash using some different methods and better materials and it turned out great: kzfaq.info/get/bejne/jqhpeq59t669foE.html

@calabar92 2 жыл бұрын

Very honest and straightforward. Great video

@6thGearGarage 2 жыл бұрын

Thanks! I recently gave it another try with different materials and the result was much better kzfaq.info/get/bejne/jqhpeq59t669foE.html

@TheMityquin 10 ай бұрын

I loved this video because of the mistakes you made and how you showed how to go back to fix the mistakes.

@6thGearGarage 10 ай бұрын

Thanks for watching! I later restored another dash using spray foam, brush on glue and 4-way stretch vinyl + spray paint, and the results were much better, but still had a little trouble with the recessed area: kzfaq.info/get/bejne/jqhpeq59t669foE.html Also I put both dashes through a torture test to see which products held up better and the second one was definitely the winner: kzfaq.info/get/bejne/r92bpLeSrbGWfHU.html

@naidadad9311 2 жыл бұрын

What a video! Thanks for your great details!

@guillermonieri4203 2 жыл бұрын

I think it looks very good. Thank you.

@jorgefernandez-mv8hu 2 жыл бұрын

Thanks for showing us how to do it mistakes and all. Nice Job.

@timothy2935 2 жыл бұрын

Sweet. I love KZfaq. I just bought a 77 sr5 pick up and can't wait to restore it! Love videos like these for the rest of us do it yourselfers

@6thGearGarage 2 жыл бұрын

Nice! I'm getting more into the older trucks, just got a 1980 long bed to restore. I really like the quad headlights on the earlier trucks like yours.

@timothy2935 2 жыл бұрын

@@6thGearGarage same dude. Beautiful truck

@chivomachete 2 жыл бұрын

Thanks for the real video ,, you did good bro

@blueovalracing1582 2 жыл бұрын

Great video my friend I enjoyed how you kept this video real which means how shit really happens when you're working on something

@ValentinArzola Жыл бұрын

Awesome job man! The experience is worth the hassle. The more you do it the better you will get.

@6thGearGarage Жыл бұрын

Thanks! I recently restored another dash using spray foam, brush on glue and 4-way stretch vinyl and the results were much better: kzfaq.info/get/bejne/jqhpeq59t669foE.html

@kws1957 2 жыл бұрын

Flower Waltz of Tchaikovsky in the Nutcracker Suite (or Vals Zvetov). Thank you and God bless you ! (Exquisite Taste of music !)

@kululv 2 жыл бұрын

wow! that was great! I like the idea with the bondo mold! i think it looks really nice. Specially compared to the alternative

@topcat5988 2 жыл бұрын

I felt so bad for you and all your hard work…but you got it done! Good work!!!

@6thGearGarage 2 жыл бұрын

Thank you!

@cjespers 2 жыл бұрын

Thanks for posting!! Very nice job!!

@MrGonzales1982 Жыл бұрын

Great video thank you for the tutorial, must say it's refreshing to watch a real video.

@6thGearGarage Жыл бұрын

Thanks! I recently restored another dash using spray foam, brush on glue and 4-way stretch vinyl and the results were much better: kzfaq.info/get/bejne/jqhpeq59t669foE.html

@simba9725 2 жыл бұрын

Lay the vinyl down first in the recess areas first then work your way outward. But it still looks really good seeing how this is the first time you tried it.

@rich6841 2 жыл бұрын

Well I've be watching a lot of ways of doing wraps, It's going to be some fun trying different way's. I'm up for the challenge one way or another wish me luck. Great do's and don't to watch for ,video was awesome.

@TeslaArhimedovich 2 жыл бұрын

Great job, not everyone is given such creative talent.

@6thGearGarage 2 жыл бұрын

Thanks! I recently gave it another try with different materials and it turned out MUCH better! kzfaq.info/get/bejne/jqhpeq59t669foE.html

@braulionieves9478 2 жыл бұрын

Really appreciate these videos man

@xavierriestra9200 2 жыл бұрын

ive never used it before but i feel like 4 way stretch vinyl would have helped here but i liked that you left all the mistakes in the video it shows the reality of diy projects

@6thGearGarage 2 жыл бұрын

I'd like to try another with 4-way stretch vinyl.

@neilreid2298 Жыл бұрын

Really great video- enjoyed the story and learning as you went along. Thanks for all the hard work!

@6thGearGarage Жыл бұрын

Thanks for watching. I recently restores another Toyota dash using spray foam, 4-way stretch vinyl and brush-on glue, and the results were much better! kzfaq.info/get/bejne/jqhpeq59t669foE.html

@yahyaallauddin8744 2 жыл бұрын

It's very helpful for bigners and it's look very nice honestly

@Sirio69 3 жыл бұрын

Thanks so much my friend , I have Toyota pickup 92 Tenerife Islas Canarias

@markdaugherty6378 3 жыл бұрын

Thanks for sharing learned something new

@paramtrx9558 3 жыл бұрын

I like that heat lamp!

@byrnejr 2 жыл бұрын

Came out nice ! Ty for sharing

@debouch 2 жыл бұрын

Working with a steam engine would be easier. But congratulations for the video and this kind of diy project always has some last minute problem to solve. Practice leads to perfection. Greetings from Brazil.