7 ways to SHRINK METAL // HOW TO

  Рет қаралды 52,897

Metal Shaper Tom

Metal Shaper Tom

Күн бұрын

www.paypal.me/TWilkes460
Please support my channel 👨‍🏭
7 different ways to shrink metal
Hopefully at least one of them will be helpful to you and your project.

Пікірлер: 83
@AerialLensVideo
@AerialLensVideo 5 ай бұрын
THANK YOU! Really well done video - Very consise yet also comprehensive, covering quite a lot. Being on a tight metalworking budget (more time than money here), this is so helpful in showing what I ACTUALLY NEED to do a good job.
@TalRohan
@TalRohan 6 ай бұрын
Those shrinking dies look like a refined version of the shrinking hammer and dolly, and a lot kinder to the steel. I havent done much sheet metal work but it is in my realm of interests Thanks for the information and the demo
@ryannichols8315
@ryannichols8315 6 ай бұрын
I use a propane Torch on body panels all the time. The trick is when it's popping in and out, if it's right when it pops in. Then you just need to heat the area and quench it. It will usually retract to that popped in position. If it's the out position. Then take a body hammer with the spike and hit it in the middle to basically stretch it to the middle in a tighter spot. And start shrinking.
@bennyhill3642
@bennyhill3642 6 ай бұрын
I can really understand what your showing us. I cant say that for alot of the vids on stretching and shrinking metal. Gr8 vid thanks again😇😁
@Metal_shaper_tom
@Metal_shaper_tom 6 ай бұрын
Thanks 👍
@Handbuilt1
@Handbuilt1 Жыл бұрын
(As a suggestion) try this,..... when tuck shrinking , rather then close the tuck a the front , close it at the rear first on the folded line then a little on the sides , this will keep the tuck from opening too much and give you much less material (bumps ) on the flange you also will achieve more shrinkage THEN SIMPLY take the rest down towards the front . The same applies when shrinking on the wooden stump except it's done on the inside of the panel not the out side . By the way... those shrinking hammers are only good as meat tenderizers
@xmo552
@xmo552 Жыл бұрын
By "front" do you mean in the inside of the curve ?
@Metal_shaper_tom
@Metal_shaper_tom Жыл бұрын
thanks peter. big admirer of your work
@user-ym6ci5ye3x
@user-ym6ci5ye3x 2 ай бұрын
Very very nice
@gavin6538
@gavin6538 2 жыл бұрын
A very good explanation of the options. The first time I watched a shrinking fork wasJaphands making one. He then showed how to use it and it looked a mess until the last few minutes it all became clear that it was very effective at doing the job and you suddenly understand. A bit like watching Rolf Harris drawing you think what the hell is he doing then you have that moment when you get what he was drawing. That just showed my age a bit.
@nexpro6985
@nexpro6985 14 күн бұрын
That was bangin'
@jimmyattard1446
@jimmyattard1446 Ай бұрын
Tom, I've watched shrinking videos for years, all showing different methods with out a clear message of why their way works. Thanks for bringing all the ideas together so rookies like me can understand! Two questions... #1 Why the ardent dislike for shrinking hammer process? Is it marring the surface that you dislike or is there more that's negative about it? #2 I successfully stretched out my wheel wells to gain tire clearance by 1/4"at the top. After a while, a slight wave appeared on the body about 3"over the top. I have no access from behind for a dolly. Would you recommend i use a shrinking disc to get the body above the wheel arch back down? Thanks ahead of time.
@mikeanderson1139
@mikeanderson1139 2 жыл бұрын
as a real novice in metal, i really got a lot out of this video. Thanks!
@Metal_shaper_tom
@Metal_shaper_tom 2 жыл бұрын
That’s great to hear Mike . Thanks for watching 👍
@GuideCoatGarage
@GuideCoatGarage 9 ай бұрын
Excellent video, cheers.
@custom.restore
@custom.restore 2 жыл бұрын
Great tutorial guys!! Nice to see the channel grow too 💪
@jmartin4030
@jmartin4030 2 жыл бұрын
Good video, now I know why my shrinking hammer didn't work, I don't have a shrinking dolly.. didn't know they existed until now, thank you...
@Metal_shaper_tom
@Metal_shaper_tom 2 жыл бұрын
Thanks for watching 👍 glad you liked it.
@VanishingNomad
@VanishingNomad Жыл бұрын
Shrinking hammers are meant to be used with heat. If you use them cold, you damage the sharp points on the surface and they stop working. So go to the section where he heat shrinks with the torch, use your shrinking hammer there. Thats how they are meant to be used. I am not sure why no one knows this anymore, but it was common knowledge when i was a kid (I am 55 now)
@oldmanonabike233
@oldmanonabike233 Жыл бұрын
Excellent explanation, thanks.
@seanalexander9531
@seanalexander9531 2 жыл бұрын
Awesome tips - thanks!
@Metal_shaper_tom
@Metal_shaper_tom 2 жыл бұрын
Cheers Sean 👍
@davidcraemer8227
@davidcraemer8227 2 жыл бұрын
Awesome video, thank you.
@Metal_shaper_tom
@Metal_shaper_tom 2 жыл бұрын
Cheers David 👍
@rogerphillips450
@rogerphillips450 Жыл бұрын
Thank you.
@Freebird67
@Freebird67 2 жыл бұрын
Excellent as ever Tom thanks
@Metal_shaper_tom
@Metal_shaper_tom 2 жыл бұрын
Thanks Wade 👨‍🏭
@billkahl1147
@billkahl1147 2 жыл бұрын
Great video with a lot of useful content. Thanks for posting.
@Metal_shaper_tom
@Metal_shaper_tom 2 жыл бұрын
Cheers bill 👍
@jraposo911
@jraposo911 Жыл бұрын
Love these techniques
@Metal_shaper_tom
@Metal_shaper_tom Жыл бұрын
Thank you 👨‍🏭
@Squintanditsmint
@Squintanditsmint 2 жыл бұрын
Nice one, thanks for pulling this together.
@Metal_shaper_tom
@Metal_shaper_tom 2 жыл бұрын
Thanks 👍
@Defender110SLO
@Defender110SLO 2 жыл бұрын
Ciao and thanks. Cheers. 🍻
@samrodian919
@samrodian919 10 ай бұрын
A very, very informative video Tom. Thank you for that. 'It's a pity I didn't know about there methods 35 or so years ago when I was repairing a front corner crash damaged VW caravanette I had bought ended having to make and put in a new n/s floor pan coz I could not get the ripples out of it lol. The front panel had to have a fair lot of filler in it to get rid of the dents !
@dougwernham5209
@dougwernham5209 2 жыл бұрын
Excellent video very helpful thank you.
@Metal_shaper_tom
@Metal_shaper_tom 2 жыл бұрын
Thanks Doug 👍
@woodwardmotors6758
@woodwardmotors6758 2 жыл бұрын
Nice to see your pullmax dies work so well👌
@Metal_shaper_tom
@Metal_shaper_tom 2 жыл бұрын
Hey Tom yeah they work well.there’s still a bit more refinement to do with them to get them working better tho. 👍
@tinwerx9871
@tinwerx9871 2 жыл бұрын
Yet another great video! Thought you may like to know that many years ago before Wray invented the shrinking disc I was taught that if you use 2old sanding discs(not Velcro or self adhesive) face to face using the rear smooth surface also works, some discs really smell bad though! I have also used an old stainless saucepan lid to make a shrinking disc but sanding discs are safer!
@Metal_shaper_tom
@Metal_shaper_tom 2 жыл бұрын
Hi 👋 thank you! We still use the upside down sanding disc technique and it works really well! Another great way that not many people know about! 👍
@kieren7763
@kieren7763 2 жыл бұрын
When I first started I used to make one piece reverse cowls making a long u shape first with the bead in the middle then tuck shrinking the 3 to 5 inch edge kind of like your were then trim the bonnet profile and roll all the edges and do wire edge on the back they looked awsome but the tuck shrinking still gives me nightmares used to take about 40 hours to make them with a power hammer not even a full day
@DGRetroCustoms
@DGRetroCustoms 2 жыл бұрын
awesome video, never seen the shrinking disk used before but it looks very effective I may have to invest
@Metal_shaper_tom
@Metal_shaper_tom 2 жыл бұрын
Cheers Danny 👍 yeah it’s an awesome tool. Stakesy’s do one for £50 but I couldn’t afford that at the time hence making one.
@DGRetroCustoms
@DGRetroCustoms 2 жыл бұрын
@@Metal_shaper_tom looks spot on for removing warpage after welding will defo be looking for one when i am a little more flush
@daos3300
@daos3300 2 жыл бұрын
very nice presentation. when using the tucking fork, if you heat the tucks before hammering it'll curve quicker and you'll save yourself a few rounds of hammering.
@Metal_shaper_tom
@Metal_shaper_tom 2 жыл бұрын
Indeed, this was just a quick overview on each separate technique, we're assuming most people won't have oxytetracycline at home.
@johnwillman3216
@johnwillman3216 11 ай бұрын
Sorry I hit the wrong hand. Very good video
@Piekielnikskateboarding
@Piekielnikskateboarding 2 жыл бұрын
Great video well explained subject 👍👍👍
@Metal_shaper_tom
@Metal_shaper_tom 2 жыл бұрын
Thank you 👨‍🏭
@JazzStrat781
@JazzStrat781 2 жыл бұрын
Great video 👍 new subscriber here, I appreciate all of your content
@Metal_shaper_tom
@Metal_shaper_tom 2 жыл бұрын
Thanks for subscribing 👍
@StevesConsul
@StevesConsul 2 жыл бұрын
Another great video Tom, nice to have all the shrinking methods in one video. I still haven't solved the oil canning on my doors, if I run a shrinking disk all over the high area do you think that would stop oil canning ?
@Metal_shaper_tom
@Metal_shaper_tom 2 жыл бұрын
Hey Steve! Thanks very much. Personally I would say yes it would work but I wouldn’t want to be responsible for you spending £50 on one and it doesn’t 😬 if you get what I mean.
@Bigskyguy56
@Bigskyguy56 2 жыл бұрын
A great tutorial on Shrinking Metal. You provided good & useful info. Have you considered doing a tutorial on Stretching metal & the assorted tools & processes? Rick
@Metal_shaper_tom
@Metal_shaper_tom 2 жыл бұрын
Hey Rick . Thanks for watching. If I’m honest no not really as I don’t think it would be that popular (I may be wrong) I certainly won’t rule it out for a possible video in the future. As your Watching quite a few of our videos now what type of thing would you like to see?
@hellkell8693
@hellkell8693 3 ай бұрын
Don’t you work harden the metal with all the bending and hammering? would annealing the metal during the process be a benefit? Great video, cleared up some of my long held confusions. Thank you.
@Metal_shaper_tom
@Metal_shaper_tom 2 ай бұрын
Yes absolutely. Will all depend on what your making at those time
@Joe.Doucette
@Joe.Doucette 2 жыл бұрын
Good quick overview video, Tom. Like you, I've never been a fan of "shrinking" hammers. They are meat tenderizers at best and not even good at that. ;)
@Metal_shaper_tom
@Metal_shaper_tom 2 жыл бұрын
Well put joe! Reminds me when I brought an apprentice a meat tenderiser and told him it was a shrinking hammer lol
@Joe.Doucette
@Joe.Doucette 2 жыл бұрын
Hahahahahhaha! That must have been fun.
@russelljones5294
@russelljones5294 2 жыл бұрын
thanks for the video, it was very informative. can you give me some info (manufacturer/supplier) on the blue english wheel you were using. i currently have a low-end budget machine and would like to move up to something a little better, do you have any recommendations for a mid-range tool?
@Metal_shaper_tom
@Metal_shaper_tom 2 жыл бұрын
Hi Russell. It’s a stakesy’s prototype so not actually on sale yet and will be in the region of £1000 it’s a copy of a Justin baker wheel that is £2400 . Baileighs cheap wheel at £700 is also very practical but not cast. Hope this helps a little
@jessejenks5401
@jessejenks5401 Ай бұрын
Hi, what technique could I use to shrink in the middle of a thin aluminum 6061 T6 panel? I have a small dent from a rock in my airplane. It’s only about 1/2 inch around, but I’m afraid if I hammer it out I will just stretch the metal. It’s in a large flat area. Thanks!
@Metal_shaper_tom
@Metal_shaper_tom Ай бұрын
I much you can do really. Try putting a strip of leather over a Dolly and gently tap down to avoid stretching
@jessejenks5401
@jessejenks5401 Ай бұрын
@@Metal_shaper_tom ok, I’ll give it a try. Thanks!
@johnterschak120
@johnterschak120 5 ай бұрын
Tom, Are you in the States or UK. Where?
@Metal_shaper_tom
@Metal_shaper_tom 5 ай бұрын
Uk based
@basilwatson1
@basilwatson1 Жыл бұрын
😀...its a science from the gods ... stick with Uri Geller ,,, at least he made things achievable! ( just kidding ! the talent these folks have is awe-inspiring! )
@Metal_shaper_tom
@Metal_shaper_tom Жыл бұрын
Thank you Stephan 👍
@eaglebaldonetough4074
@eaglebaldonetough4074 2 жыл бұрын
Hi!These machines let marks on metal!Wray schelin work does not...
@Metal_shaper_tom
@Metal_shaper_tom 2 жыл бұрын
Fantastic 👍
@stick9648
@stick9648 Жыл бұрын
Wray is a magician, he can turn metal into clay and back again , be careful very careful when trying his magic.
@mikepruett1745
@mikepruett1745 Жыл бұрын
how bout on todays cars ??
@Metal_shaper_tom
@Metal_shaper_tom Жыл бұрын
What about today’s cars . Give me an example
@mikepruett1745
@mikepruett1745 Жыл бұрын
@@Metal_shaper_tom the hss on these cars is not that forgiving
@markpullen6116
@markpullen6116 7 ай бұрын
I had a bolt shrink, just by removing it from my derrallieur gear on my racing bike to replace the wire, I had to go and buy a replacement bolt because the one I had, no longer fitted due tom mysterious shrinkage, I went to my mates house and explained what had happened and he claimed this was an impossibility, but when I showed him he was a mystifed as i was and saw how wrong we all are when we say it is impossible for a metal bolt to just shrink, with no extreme heating or cooling or anything, we are both living witnesses to the contrary and NO im not joking or making it up or anything. My only question is just out of idle curiosity, does anyone understand why the fuck this happened
@Metal_shaper_tom
@Metal_shaper_tom 7 ай бұрын
Haven’t got a clue 🤷‍♂️
@sblack48
@sblack48 2 ай бұрын
Shrinking hammers and dollies are horrible things and should be outlawed.
@Metal_shaper_tom
@Metal_shaper_tom 2 ай бұрын
😂 agree
@jimmyattard1446
@jimmyattard1446 Ай бұрын
Do you not like the shrinking hammer because it Mars the surface or is there another reason? I'm just a beginner so the details are important. Thx
@sblack48
@sblack48 Ай бұрын
@@jimmyattard1446 it does more than mars it, it mangles it
@jimmyattard1446
@jimmyattard1446 Ай бұрын
Thx Mr Black
Dent repair using a slapper
18:13
Metal Shaper Tom
Рет қаралды 79 М.
Дибала против вратаря Легенды
00:33
Mr. Oleynik
Рет қаралды 2,7 МЛН
Backstage 🤫 tutorial #elsarca #tiktok
00:13
Elsa Arca
Рет қаралды 47 МЛН
The Ultimate Heat Shrinking Video
8:13
Auto Body Training Solutions
Рет қаралды 75 М.
Heat shrinking a oil canned area.
21:54
Chriscoe’s Body Shop
Рет қаралды 23 М.
Heat Shrinking 2.0
10:51
Auto Body Training Solutions
Рет қаралды 13 М.
19 Amazing Metal Work Processes You Must See ▶7
15:02
TechFreeze
Рет қаралды 872 М.
Shrinking Disc Magic
14:54
Wray Schelin's ProShaper Workshop
Рет қаралды 24 М.
Dent Repair - How To Use A "Shrinking Disc" For Beginners -- Tips And Tricks
15:23
Blacksmithing - Forging dome head rivets
10:59
Torbjörn Åhman
Рет қаралды 3 МЛН
Как не переплачивать автомойкам
0:26
Рубить Правду
Рет қаралды 1,4 МЛН
Como abrir a porta de um carro com ímã 🧲 #diy #tools #carros #shorts
0:23
3 wheeler new bike fitting
0:19
Ruhul Shorts
Рет қаралды 48 МЛН
РОССИЯДА МУСОФИР АВАРИЯ БУЛДИ
0:17
Yakka Tv
Рет қаралды 554 М.
Оживляем Tiguan втайне от Ильдара!
1:12:26
Команда АП
Рет қаралды 787 М.
Volkswagen судится с Volkswagen?
1:00
Кик Брейнс
Рет қаралды 1,9 МЛН