Excellent teaching. Even someone who has no idea about electronics can learn something from IMSAI Guy.

Sir, I am an electronics engineering student and I must say your videos helped me out a lot. Thank you.

I love your videos because you explain the purpose of the chosen components and why they are there. Over time I see the same patterns in lots of circuits and I can easily spot a voltage divider and rectifier bridge.

much better then my electronics 101 class. i am rusty on the math, and appreciate the breakdown!

I really enjoy (and appreciate) the way you cover every detail in your videos. Thank you and Keep up the great work!

This is my 1st tutorial of yours I am watching and it is so helpful as I am a beginner electronics learner. Thank you! 🙏🏼

I built the original smart kit psu back in 1995, and never found any analysis of how it works. Thank you!

BTW: I love these types of videos, you do a great job..

Thank you ❤️

I love these types of videos

Thanks for the video.

Muchas gracias, amigo...

I have the "fake" version of this board. I'll watch your whole series... I have plenty of 5v and 12v fans, and fairly larger heat syncs salvaged from CPUs etc. I just have to source a nice AC transformer for this... As I have learned, you can not use a DC transformer. I'm sure you mention this somewhere along the way... :) Dabbling in electronics, and building kits like this is great. I wish I would have started sooner.

Good video Thanks

Good job👍!!!

Even at 12v, the power dissipation in the fan regulator will become problematic. A typical 12v fan will draw over 100ma which is over 2 watts, definitely will need to add a heat sink. I used a small switching buck converter module to run a 12v fan.

The bridge diodes at 3A DC out will see about 4.5A RMS, with top-wave spikes above 20A; not just 3A as stated.

thanks

Nice

Thanks for this interesting video. I am puzzled about the bleeding resistor. Is the capacitor not discharging over the diode bridge and the secondary coil of the transformer? I got triggered by the fact that the bleeding R is just generating heat during normal operation and seems to make the power supply less efficient.

Wow, I've seen some poorly drawn schematics before, but this one is one of the worst !!! Thank you for translating it using the proper symbols, properly !!!

Nice 👍👍

Don't forget that the resistor across the filter capacitor also serves to discharge the capacitor for safety reasons. Although not really dangerous at this voltage, a capacitor can hold a high voltage for a long time unless discharged. My linear amplifier takes almost 60 seconds to discharge the capacitors from 3700V to below 100V. de WG2E.

I've got this power supply...haven't got this schematic though

Depending on the ratio of the input Transformer the output of the bridge will vary assuming it's a one-to-one Transformer an isolation Transformer in other words. Your filter capacitor is woefully under value voltage wise if it is a step down Transformer then perhaps a 50 volt bulk capacitor would be sufficient the chances are that's a one-to-one Transformer when you're going to have 170 volts Peak on the output note of that bridge

How is the value of the capacitor after the rectification is calculated

Can you do a video explaining how to use balance resistors. As often seen across diodes that are in series. . The series diodes are often used to increase the voltage handling capacity. And they use resistors across those diodes to "balance" the voltages. I would love to hear how this works and how to calculate them...

Are you going to recommend a suitable transformer and fan to buy? It seems from the comments that a 24v fan would be best.

Be careful if you change the 7824 regulator. There can be more than 30 V on the input: Most 7812 can not handle 30V on the input, it is 24V i think, With a 24 V transformer you get about 34V.

[QUESTION] in one of my PC switching power supplies, the fuse literally EXPLODES. Its replacement does only lead to another magnificent explosion, reducing the fuse to dust... Obviously there's a short....Ok, now, what did cause this short ? Trying to find out why, I found and/or saw 6 elements that are broken : 1) a thermistor (SKC-2R56, diameter 13mm, R=2.5 Ohms, 6A), just after the fuse, is broken (the upper part) 2) the bridge rectifier (GBU606 mounted on a heatsink) : it's dead (a test, unsoldered from the PCB, showed only 2 diodes of the bridge are ok) 3) a N-channel MOSFET (MDP13N50, mounted on the same heatsink) seems dead as well (tested off the PCB) 4) an IC has partially exploded (I can see its guts partially), and I can only see it's 2 first ID digits : "A6...". After a research, I found that it's most probably an IC of the STR-A6000 series (Off-Line PWM Controllers with Integrated Power MOSFET, the sixth pin of the normally 8 pins is absent) 5) after a test of the surface components below the PCB, I found one diode that is dead. 6) the big filter capacitor (400V, 180µF ) is dead as well : test gave me 5.5nF I think it's not a good idea to repair it, too many broken components, but ask myself, what did cause that short-circuit in the first place ? I suspect the bridge rectifier is the culprit of that disaster, any similar experience ?

Am I correct in assuming that you'll have to short the output to set the current limit?

Hi, what again is the purpose of the 3300 uF capacitor? I get how the bleeder resistor works due to the existence of the capacitor.

Theoritically speaking if you really wanted to use the 7805 could you hook up a 7812 in front of it you know conect the 12 output to the 7805s input would that do anything usefull would it even be a good idea?

Sad that we are loosing the basics of simplicity

I disagree. CAD let’s me draw great schematics. As I add or alter subsections I can move whole blocks of the circuit around to make my intent more clear instead of jamming it in whatever space I have left. I always try to make voltage dividers looks like voltage dividers or inverting op amps with gain resistors look like their canonical textbook form so someone can glance at my schematic and immediately recognize the intent I had behind those resistors. The original schematic hear is either pure laziness, or someone who has no idea what any of the symbols mean copying a schematic from somewhere else into a new publication.

Nice but please, for God's sake, stop hiding everything with your hands all the time ! You always hide the only things we can see ! Use some kind of tip, it would be much nicer for your subscribers....

Stop moving your hands all around it's very distracting. Thank you.............