Awesome vid sir! Definitely like the idea of not having to pull the axle off, I’m totally going to do a conversion now. Thanks!

Literally just started looking into conversion kits 15 minutes ago. Went to KZfaq after to see a step by step and man this video was the first I clicked on. Great explanation and just ordered the parts man. Thank you!

you should do another video of bleeding procedure, and review overall performance.

Awesome brother! what a great video my ls1gets swapped out tomorrow! Brakes are my next step! Thanks again

It’s a nice kit, I put one on my ‘95. Bought so I would not have to pull the axles. Turns out my axle seals were leaking so I ended up pulling them anyway. Nice kit and fairly easy to install. I also replaced my master cylinder with a ‘02 Tahoe mc, worked out very well. Nice video!

lot of good info, thank you....and you are so correct. The rears have always been the worse on these trucks

props on cutting out those inner plates...time saver from opening up the diff, and pulling the axles.

Just got a 2wd 2 door Tahoe, got a lot of the suspension “done” for now, in the middle of body paint right now. It’s still my daily so. But a very helpful video, excited to put this set up on mine I’m sick of the drums too man

I hate drum brakes but in my obs just went to a 2000 and up shortbed rearend👍🏿

That's funny you'd say that you reminded me of that guy that was humping the exhaust pipe on that little car on on Facebook

Drum breaks ! Ain’t nobody got no time fo dat ! Lol yeah man awesome video. I got my 99 suburban work truck and I carry about a couple thousand extra pounds of tools and ladders in and on it. I really need to do this !

Holmes, I hear you. Even if they work just as good or not much better, I would still rather replace pads vs shoes. Great upload. Cheers 🍻

Nice vid, good detail and explanation. I like the music too!

The later model master cylinder they offer will help even more than just the rear disc.

Like the video. I aso have the same truck am looking to change my back bakes to disc brakes it looks a lot better 👍

great video man ... very cool to see how you did it

Would have liked to see a finished test drive and performance review, but appreciate the video.

I was told one time that converting your rear drums to disk was not a good idea bc the rear disks would grab just as hard as the fronts sending you into a skid.

Good shit bud...

Bro you are absolutely right about drum brakes. I was talking to a buddy of mine about them, and I told him they are a safety Hazzard! Its a reason why manufacturers UPGRADED from them. I'm about to do the same thing on my OBS too. But I'm going through the rear-end as well, gonna do a posi on it

Nice install video.

If you haven't swapped out your master cylinder.. Swap it with a NBS master cylinder.. I have a 02 MC on my 96 Short Bed.. Really gives you a firm brake pedal..

How bout a link to where u bought them and thanx love the vid

GREAT VIDEO FAM

I NEED THAT CONVERTION ON MY 97....WHERE YOU LOCATED, UM IN FLORIDA

Definitely looks sexy, and you've also lightened the rear end, and its so much easier to do a brake job with fewer parts, great video dont stop making them 👍🏾

Did the emergency brake line match up What's what they gave you in the kit or was there any mods you had to do?

Hey there, I noticed you skipped the clip at 9:30 , did you have any trouble getting that black bracket onto the axel body ? It looks too tight to just slide onto it. Any tips?

Wow what a great video. I love it.

Where'd you go for your drilled/slotted rotors

Rear disc brakes are a headache, I will take drums any day - yes the drums are more difficult to rebuild, but you might do it twice in the life of the truck - the discs are always giving you issues

Awesome, thanks I gotta get mine done!!

I've been wanting to do this on my 97 , doesn't look that hard

How is it holding up, sir? I'm looking to buy this kit pretty soon here

good video with good info thanks man

does it make much a difference? I had new drums and shoes and stop just fine, not sure if I do this if it wont be much better or if the truck value would even go up

What year of truck do you buy rear pads for and what model

I see you went and got the kit for the Burb. I hope you like the kit bro

Did you bend the existing brake line over to reach the caliper or cut it out and start with a new line

Did you look into changing your master cylinder to the nbs? Ive heard even with drums it makes a world of difference.

Can I get a part number for the T valve please ? Thanks ! Keep up the good content!

Do your stock 15” rims fit fine with this rear disc kit?? 21:24

Would you share the cost of your conversion.

Got any videos on your 4 link?

Will I have to get a longer parking brake cable mine has 4 inch lift

Great video! I am wondering what four link suspension is that you have in the rear? Ride tech?

What brand c notch is on your truck?

Hello. Where did you buy that complete kit?. I have a 94 Chevy suburban and I want to do this conversion. Thank you very much for your coment.

After you did cut off the old drum you did not show how you did get the new bracket on! Why?

Where did u get the kit from need it

How did you install the parking brake cable? I'm having trouble with installing it?

Can you run a 15 inch wheel with this rear disc brake setup??

i can to buy for amazon or ebay

If I was to ever need to do a brake job would I just get pads for the front and rotors for the front and put them in the back?

Hows the breaking with the disc conversion compared to the drums?

hanging the hardware is easy, What i cannot find out from anybody is how the brake balance is , the calipers need more pressure than a drum wheel cylinder and I worry about stopping power without a new master or proportioning valve. Not one aftermarket company who sell these kits even mention brake balance. some offer a Master none offer any info on balance. I'd like that info

Good Job ! 🔧🔧

Do those rear rotors come standard on any vehicle?

Good video. Btw what's your rear suspension set up?

I had a question hopefully you can still answer mines what happens when it is time to change the brake pads what brake pads would you get ???

Hi. Where can I order that kit.

Hello i have a 89 chevy astro van and I want to use that kit to do mine can you tell me the model number you ordered

Okay here's the real question did you have any clearance issues with your wheels because I see stock will on ground they didn't see if you put it back on but see I'm one that doesn't want to run twenties on things I don't like twenties I like normal sized Wheels

Where do you get the slot drill rotors and part numbers ?

Did u replace porportiong valve??

Where can i message you about a question that i have ??

Looks like more work easier to pull the axels

Did you hook up the emergency brake and was it the stock cable?

Hello, sorry, where can I get this kit?

Nice brakes ! You do coil over ?

Awesome vid, thank you!! I am thinking on buying the same kit, do you know what make and model are the rotors/break pads out of? I couldn't fint the part# and I am worried that maybe in the future the parts might be a little bit complicated to get Thanks in advance!!

how do u connect the ebrake?

Which kit did you get? The one for the 10” drums or 11”?

What kit was this? I'm going to rip my hair out dealing with the drums on my 96 k1500.

Are they 10” or 11 inch drums?

Looks like you have a lot of experience on mechanic jobs ! Question ! My back up lights doesn't work at all ! Bulbs are good , wires are good ! Any idea ?

Good Job Btw 💯👍🏿

please tell me you was joking about that rusty truck a show truck lmao

Hey brother ? Were you able to use your 4L60e transmission out of your suburban for the LS swap

Good job where you get the conversion kit?

Could you just have taken the four bolts out ?

Nice video,that dust cover is a bitch.Didn’t see how you put the caliper bracket on,does the cutout slide over the axle then the diff housing

how did you get the bracket on at this minute in the video? kzfaq.info/get/bejne/hbllbLF7u6jed5c.html

Could you give me a part number for air bags please

Disc

Oh wait the bearing is in the way 🥴🥴

Hooooooraaleeee.. VATO🤟🫡. I HAVE GT YUKON AND I ALWAYS WANTED TO PUT DISCK BREAK..HORA LE VATO COOL VIDEO 😊

Sik ride 👍🏻 I have a 99 Burn gettin some things done Do you got an IG Page